Search Documents

By D. K. Ingram

In situ horizontal stresses were measured to determine the influences of geologic anomalies on the regional horizontal stress field in two coal mines in southern Illinois. Stress measurements were obtained near a normal fault having a 121-ft displacement at the AMAX Wabash Mine and a large coalbed want at the Kerr-McGee Galatia No.5 Mine. Horizontal stress measurements were completed using a Bureau of Mines borehole deformation gauge. The average maximum and minimum horizontal compressional stresses at the Wabash Mine were 1,400 and 800 psi, with the direction of maximum stress ranging from N 78° W to N 83° E. At the Galatia No.5 Mine, the averages were 1,500 and 500 psi, with the direction of maximum stress ranging from N 85° E to N 75° E. Generally, the geologic anomalies appear to have no dramatic effect of the regional horizontal stresses. However, subtle differences between stress measurements suggest an influence by the fault zone at the Wabash Mine. The larger anisotropic stress conditions at the Galatia No.5 Mine could be responsible for the increase in kink zones and directional roof failures.

Jan 1, 1988

By S. A. N. Sheya

Many gold-bearing ores in the Western United States also contain small amounts of mercury. The presence of mercury creates potential pollution and health hazards during several steps in gold processing. An investigation was undertaken by the Bureau of Mines to develop techniques for removing mercury from cyanide mill solutions by selective electrowinning to reduce the potential hazards. Sixty-five percent of the mercury was selectively electrowon from synthetic carbon strip solution at applied potentials of 1.00 to 1.50 V when using a mercury-coated platinum or copper plate cathode. Increasing the active surface area by using mercury-coated copper wool resulted in up to % pct of the mercury being electrowon from mill carbon strip solutions that contained 1.9 to 20 ppm Hg, 20 to 345 ppm Au, and 0.35 to 39.5 ppm Ag. About 98 pct of the silver was electrowon with the mercury onto the mercury cathode. Gold extraction ranged between 0 and 20 pet. Results of the investigation showed that choice of cathode material was critical to the success of the process. Selectivity was not achieved using uncoated steel wool cathodes.

Jan 1, 1988

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988

By J. S. Walker

The Bureau of Mines monitored surface subsidence and water level fluctuations in 10 shallow observation wells above a series of four adjacent longwall panels in southwestern Pennsylvania, for about 4 yr. This study attempted to correlate the changes in the water levels within the observation wells to the measured vertical and horizontal ground movements associated with subsidence. Results of this study indicate that the fluctuation of the water levels appears to be a function of the well location relative to the mine layout and the proximity of mining. Wells are generally unaffected by mining of a preceding panel unless they are located within the angle of draw for that panel. Wells located at the centerline of a longwall panel exhibit the greatest fluctuation and head loss. This relationship may be related to the strain developed by the advancing longwall face. The water levels in the wells monitored fell at the greatest rate when the ground surrounding the well was in tension. The rate of the decline decreased as the dynamic development of the strains was changing from tension to compression. The water levels were found to be near the premining level before the ground was subject to maximum compressive strain. Nine of the ten wells investigated recovered to their premining water level after mining was completed.

Jan 1, 1988

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines-developed induction slag melting process is of concern to the titanium industry. The objective of the research was to determine the effect of removing the nonconductive molten calcium fluoride (CaF2) slag used as an insulator between the titanium and the segmented copper crucible. The data were obtained from single-induction-melted ingots prepared with no CaF2 insulating slag and an ingot prepared with the normal addition of 4 pct CaP2 slag. The results showed that the mechanical properties of single-induction-slag-melted and annealed Ti-6AI-4V alloy exceed the minimum values specified in "Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H." High-cycle, tension-tension fatigue testing yielded similar results. The data from 44 of the 45 specimens were contained within the typical scatter band for fatigue data on wrought Ti-6AI-4V alloy. Although the removal of the insulating slag is a desirable change, the data from the specimens with the previously standard 4 pct slag addition showed no detrimental effect from the slag inclusions.

Jan 1, 1988

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By Samuel R. M. Burton

This Bureau of Mines report describes a method for determining parts per million (ppm) of helium-4 (He-4) in helium-3 (He-3) to an accuracy of ±5% by mass spectrometry. Gravimetrically prepared primary standards were used for the calibration of a Dempster 1800 magnetic sector mass spectrometer. A comparison between a 2.49% He-4 in hydrogen mixture and a 2.49% He-4 in He-3 mixture shows that He-3 can be replaced with hydrogen as a diluent for standards with comparable mass spectrometry sensitivities for He-4. Using hydrogen as a diluent allows analysis of He-3 samples for He-4 when He-3 for preparation of standards is not available and also conserves the rare He-3 isotope. Standards of He-4 in Hz were prepared for calibration of the mass spectrometer for quantitative determinations of He-4 in the 2-to 100-ppm range. A minimum detectable limit of 2 ppm He-4 is obtained by this method.

Jan 1, 1989

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984