Search Documents

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By Filipe de Menezes Torres, Augusto Pereira de Sa, Itavahn Alves da Silva, Eliana Ferreira Rodrigues, Carlos Antonio da Silva, Varadarajan Seshadri

Top slag eye opening which happens as a result of gas injection is a function of the gas flow rate in addition to other factors such as ladle geometry, porous plug location as well as slag properties. Slag eye opening leads to entrapment of atmospheric nitrogen, oxygen by the steel melt affecting adversely the steel quality. In this work aspects of mixing and eye formation in steel making ladles with inert gas injection have been analyzed through physical and mathematical modeling techniques. Influence of ladle, gas flow rate and distribution and slag properties has been assessed. A correlation for estimating eye opening has been developed. Results from PIV measurements and images of eye opening obtained using a camera have been utilized to validate results from CFD simulation.

Jan 1, 2015

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By Hökmark. H., M. Lönnqvist

"The Swedish Nuclear Fuel and Waste Management Company are planning to construct a permanent storage facility for high-level nuclear waste at about 500 m depth in fractured crystalline rock. One potential concern for the long-term performance of the repository relates to large fracture shear displacements, since these may damage intersected waste containers. Although details in fracture surface geometries are known to influence slip magnitudes and distributions, fractures are commonly approximated as planar features with lab-scale properties due to lack of relevant field-scale data and to limitations in available modelling tools. The purpose of the work described in this paper is to explore the possibilities to use the distinct element code 3DEC to generate and analyze models with isolated, non-planar fractures and, based on the results of such models, get perspectives on the influence of basic disturbances such as ridges, steps and waves. Given the model set-up, fracture segments with orientations deviating from the critical one will contribute to stabilize the fracture. As a result, all analyzed non-planar fractures slip less than the critically oriented planar fracture. We demonstrate that the angle of deviation is the most influential parameter determining the slip magnitude for comparable surface geometries. Similarly inclined steps and ridges have almost equal slip reductions despite differences in surface area restricting the movement. Although it may be possible to translate the influence of such irregularities to an effective coefficient of friction that could be used as input to models with idealized planar fractures, additional analyses with randomly shaped and distributed asperities, different fracture sizes and with alternative stress loads, need to be carried out to devise a defensible strategy for this type of parameter variation. INTRODUCTIONThe Swedish Nuclear Fuel and Waste Management Company’s (SKB) concept for deep geological storage of high-level nuclear waste is the KBS-3 method according to which the waste will be encapsulated in copper canisters and deposited, surrounded by compacted bentonite clay, in vertical deposition holes at about 500 m depth in fractured crystalline rock (SKB 2011). A site has been selected in the Forsmark area, which is located some 120 km north of the Swedish capital Stockholm. One potential concern for the long-term performance of the repository that has been identified by SKB (SKB 2011) is related to large shear displacements along repository host rock fractures induced by a nearby earthquake, since these may cause mechanical damage to intersected waste containers. Due to lack of relevant data at the appropriate field scale and to limitations in available modelling tools, fractures are commonly approximated as planar features with lab-scale properties. The standard numerical tool, 3DEC (Itasca 2013), used in SKB’s rock mechanics analyses, for example, generates planar fractures by default. Results from dynamic 3DEC earthquake-models (Fälth et al. 2010) currently provide input to layout decisions, i.e., the diameter of the smallest planar fractures that must be avoided when deciding on waste container positions at different distances from potential earthquake faults. It is, however, well known that fracture surfaces are rough or undulating on a wide range of scales (e.g., Candela et al. 2012) and that such deviations from planarity influence the mechanical behaviour of the fractures (e.g., Dieterich and Smith 2009, Marshall and Morris 2012, Ritz and Pollard 2012). It will probably never be a realistic option to attempt to represent the geometrical complexity of a population of fractures of different size, shape and surface structure in any large-scale rock mechanical analysis relevant for the performance assessments of the nuclear waste repository. It may however be possible to find approximate ways to represent different styles and degrees of non-planarity by assigning mod"

Jan 1, 2015

By K L. Olzard

At the WMC Resources Phosphate Hill operation, monitoring the quality of the ore delivered by the mine to the beneficiation plant is of prime importance to ensure the fertilizer is produced cost-effectively through the various stages of production and meets customer quality requirements. P2O5 and Fe2O3 are among the critical-to-quality elements. Fe2O3 is a key performance driver as it is an impurity that adversely impacts some of the chemical processes. The ore is supplied to the plant on a conveyor belt that is equipped with an automatic sampler. Increments are taken off the flowing ore stream at regular time intervals. A variographic experiment was conducted to investigate sampling strategies capable of estimating ore properties over a 12-hour shift to a nominated level of precision. The combination of individual increments into a shift composite was included among the strategies that were assessed. The experiment involved collecting data at regular time intervals and preparing variograms to characterise the feed-grade variability on the conveyor belt. Duplicates were also collected to assist in quantifying the precision of the subsampling stages of the sampling protocol and assay accuracy was monitored with matrix-matched standards. Various sampling schemes were evaluated by combining geostatistical techniques and the sampling theory of Pierre Gy. The following parameters were varied: the number of increments, the increment-size reduction leading to the composite, the masses of the subsequent sampling stages and the number of analytical determinations. This paper describes the planning of the variogram experiment, the various phases of data collection and the methodology used to process the data. It discusses the development of some of the sampling schemes that were considered.

Jan 1, 2005

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL'S, KNOTHE'S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989

By Renan Oss Giacomelli

The adhesion of multifunctional coatings on soft substrates is of paramount importance in the tribological behavior of this important class of surface treatment. In particular, scratch and indentation tests have been extensively used in order to assess this property. In this paper, the adhesion of a-C:H diamond-like carbon films deposited on nitrided low carbon steel was evaluated by indentation and scratch tests. The coatings were produced by PECVD onto 1020 steel substrates with two different surface finishing: ground (Sq = 0.184 µm) and polished (Sq = 0.002 µm). Indentation tests using a Rockwell diamond indenter were conducted and the adhesion evaluated by measuring the spalling region on images obtained by using optical microscopy. The analysis of the spalling regions produced semi-quantitative results, eliminating the subjective qualitative analysis proposed by the standard method VDI 3198. In addition, scratch tests were performed using the same indenter and a comparison between the two techniques was established.

Jul 31, 2018

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

The article presents an outline of methods and certain results of laboratory tests, underground tests and model tests, aimed at assessing performance of a powered shield support on the floor of low strength parameters. The tests were conducted within the framework of GEOSOFT project co financed by Research Fund for Coal and Steel (RFCR-CT-2010-00001). The described research works were conducted by Central Mining Institute (Glówny Instytut Górnictwa), Janina coal mine and Becker-Warkop

Aug 1, 2013

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024