Search Documents

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Lewis. Clifford J.

The purpose of this article is to present design information and operating data on a pilot gas scrubber which is believed to be a new approach for removing noxious gases and particulate matter from the off gases of coal burning power plants and smelters. This principle of scrubbing gases, particularly, scrubbing with an aqueous slurry of lime, was conceived by the author early in 1972. The National Lime Association financed the design, fabrication and initial operation of the unit. The unit was fabricated by Hazen Research Inc. of Golden, Colorado. It has been tested on the off gases of two coal burning power plants and one smelter. The current environmental program has stimulated research and development activity directed toward the removal of sulfur oxides, oxides of nitrogen, particulate matter and other undesirable substances from gases discharged into the atmosphere. At present, most of this effort is focused on the removal of sulfur dioxide and particulate matter by aqueous scrubbing of the gases. This presentation deals particularly with the removal of sulfur dioxide using an aqueous slurry of lime as the scrubbing medium. In recent papers, the author has called attention to-the sludge problems resulting from aqueous scrubbing and to some earlier data on the pilot scrubber about to be discussed.1/

Jan 1, 1973

By Steve O. Green

Introduction The US coal mining industry is in the midst of a serious economic crisis. To overcome increased operating costs, operators must take advantage of technological advancements in mining systems and equipment. A relatively new concept available to underground operators is that of extending the cutting depth for continuous mining machines (continuous miners). This system is referred to as deep-cut mining, and may be described as mining cuts to depths greater than the standard 6 m (20 ft). Productivity is increased through the reduction in continuous miner tram time since the machine stays longer in each working face. To successfully implement a deep-cut mining system, three problems must be overcome: Exposing personnel to unsupported roof, methane removal, and controlling respirable dust. Remote control cutting The solution to the unsupported roof problem is remote control. Recent advances in remote operation, especially in radio remote controls, have resulted in what is generally accepted as a safe and reliable tool. By installing remote control on the continuous miner, the operator and helper can now be stationed in a supported area. This allows for improved visibility while cutting coal. With this in mind, the limiting factor now becomes the position of the haulage equipment operator. North River No. 1 uses Joy 21SC shuttle cars and Jeffrey 4110 diesel ramcars. These cars are pulled against the bumper of the continuous miner. Thirteen meters (43 ft) can be cut with the shuttle car and 14 m (45 ft) with the Ramcar before the operator of the car is inby permanent supports. By loading away from the bumper, about 1.5 m (5 ft) can be added, bringing total cut depths up to 14.5 and 15 m (48 and 50 ft), respectively. Methane removal The second problem involves methane removal, and the line curtain-to-face distance. In other words, how to maintain the line curtain to allow sufficient ventilation to remove methane and not expose workers to unsupported roof. The solution, in most cases, is to use a blowing-type ventilation system. Unlike the exhausting system that, to be effective, must be installed within 3 m (10 ft) of the working face, the blowing system can be effective at greater distances from the face. Numerous studies have documented the advantages of a blowing-type ventilation system over an exhausting system. Furthermore, a blowing system can be significantly improved by in¬creasing the velocity of the air delivered without increasing the volume of air. With this greater ventilation efficiency, it is possible to secure ventilation plan approval from the Mine Safety and Health Administration (MSHA) for a greater curtain set-back distance. This eliminates the need for personnel to travel inby permanent supports to extend the face brattice. The distance from the face MSHA will approve, however, is on a mine-by-mine basis. MSHA will evaluate the particular mine's face methane liberation rates, along with the specific proposals regarding face ventilation volumes and velocities. Dust control The third problem is controlling respirable dust. This is actually a result of the solution to the second problem. In the blowing system, while mining on the slab cut, both the continuous miner and haulage units are located on the dusty side of the line curtain (Fig. 1). In the early 1970s, underground operators virtually abandoned this system, in order to comply with the 2 mg/m3 (0.87 gr per cu ft) federal dust standards. The blowing face curtain did offer increased face ventilation efficiency. With that, greater curtain-to-face distances were also

Jan 8, 1987

By Joshua Hescock, Zach Agioutantis

"The Surface Deformation Prediction System (SDPS) has been developed as an engineering tool for the prediction of subsidence deformation indices through the implementation of an influence function. SDPS provides a reliable and fast method for the prediction of mining-induced displacements, strains, tilt, and so forth at any elevation between the seam and the horizontal or varying surface topography. One of the key aspects in obtaining reliable ground deformation prediction results is the determination of the edge effect offset. The value assigned to the edge effect corresponds to a virtual offsetting of boundary lines delineating the extracted panel to allow for roof cantilevering over the mined out area. The objective of this paper is to describe the methods implemented in updating the edge effect offset code within SDPS. Using known geometric equations, the newly developed code provides a more robust calculation of the offset boundary line of the extracted panel for simplistic, as well as more complex, mining geometries. Assuming that an extracted panel is represented by a closed polyline, the new edge offset algorithm calculates a polyline offset into the extracted panel by the user-defined edge effect offset distance. Surface deformations are then calculated using this adjusted panel geometry. The MATLAB® program was used for development and testing of the new edge effect offset feature. In completing rigorous testing regimes, the new offset features will be integrated into SDPS, further increasing the speed and reliability of the programs resulting in a retrospective increase in capability and flexibility. INTRODUCTION Underground operations have been known to cause mining-induced subsidence inside and outside of the mine permit area (Karmis, Agioutantis, and Andrews, 2008). Additionally, subsidence can impact surface water bodies, such as rivers, streams, lakes, and wetlands (Karmis and Agioutantis, 2015; Newman et al., 2016), as well as infrastructure, such as roads, railroads, pipelines, and buildings. With an increase in regulatory focus on mining-induced impacts to local structures, the calculation of mining-induced subsidence indices has become necessary in determining potential damage and mitigation efforts. The accurate prediction and evaluation of mining-induced ground deformations is required to obtain underground mining permits due to potential impacts to nearby structures, as well as hydrogeological sources. The prediction of ground deformation indices is often a complex task due to the number of input parameters required, such as mining geometries, overburden lithology, surface topography, the rate of mining (Karmis, Agioutantis, and Andrews, 2008)."

Jan 1, 2017

By Emilio Cordero Cordero

En los proyectos de excavaciones subterráneas, túneles de obra civil y galerías mineras es necesaria la realización de cálculos para el sostenimiento adecuado para cada situación y comprobar que este cumple los parámetros de seguridad indispensables para garantizar la estabilidad de la excavación en el tiempo. En este sentido, el texto señala el uso de SDT(software) como aplicación informática decuada para el cálculo de sostenimiento en túneles y galerías mineras que suministra una respuesta a las necesidades de proyectistas e ingenieros mineros. Dicho software se basa en cerchas metálicas con capacidad de deslizamiento (perfiles THN), cerchas de perfil HEB, pernos de anclaje y hormigón proyectado en túneles y galerías mineras que utiliza el método “Convergencia – Confinamiento”, procedimiento de referencia en el cálculo y diseño de sostenimiento en excavaciones subterráneas, con las premisas de sección circular, presión sobre el sostenimiento uniforme y el campo de presiones hidrostático.

Jan 1, 2016

By W. A. MacDonald, C. M. McGibbon, J. H. Reynolds

This paper traces the development of the Seaboard Power Plant, which plays such an important role in the industrial life of Nova Scotia. It also shows the involvement of the plant in the siting of a heavy water production facility in Cape Breton. The paper concludes with an outline of the new installations which the Nova Scotia Power Commission has undertaken as an extension to the Seaboard Plant.

Jan 1, 1966

By M. E. Williamson

In September 2005 Williamson & Associates, Inc. delivered the BMS2 remotely operated seafloor coring system to the Japan Oil, Gas & Minerals National Corporation (JOGMEC). During acceptance trials aboard the JOGMEC research vessel R/V Hakurei Maru No. 2 the BMS2 successfully recovered 7.44 m of rock core in 3377 m water at a site near the crest of a seamount about 500 nm SE of Japan. Hydrogenous ferromanganese oxide crust, basaltic lava, sandstone and volcanic sediments were sampled with near 100% core recovery. The BMS uses rotary rod coring tools to collect samples to a maximum depth of 30 m in water depths up to 6000 m. Depending on bottom type to be sampled, the BMS tool magazine can be loaded with various drilling tools including core barrels with different bit types, drill rod and bore hole casing. The drill has 9 video cameras, a suite of sensors and 60 hydraulic functions powering thrusters, telescoping legs, seawater pumps and all of the standard drilling controls. The BMS provides deep water investigations with the functionality of conventional diamond bit rod drilling currently the mainstay of exploration programs in land mining.

Jan 1, 2005

By P. A. Rona

The first hydrothermal mineral deposits found at a seafloor spreading center were discovered in the Red Sea by multi-national research vessels between 1963 and 1965. At that time, the deposits were considered a special case related to continental rifting and an early stage of opening of an ocean basin. Since that time, examples of almost all major varieties of volcanic- and sediment-hosted hydrothermal deposits associated with basaltic rocks in the geologic record have been found at present spreading centers. Review of over 100 hydrothermal mineral occurrences presently known at oceanic ridges and rifts indicates that a range of deposit sizes from small to large (> 1 x 106 tonnes) occurs at all seafloor spreading rates. However, larger deposits but fewer per unit length of spreading axis appear to form at slow- than at intermediate- to fast-spreading centers based on available data. Larger deposits are more common in sediment-hosted than in volcanic-hosted settings regardless of spreading rate. A spectrum of hydrothermal deposit varieties (stratiform, stockwork and disseminated sulfides; various forms of sulfate, carbonate, silicate, oxide and hydroxide deposits) occurs in almost all of the tectonic settings. High-intensity, ore-forming, subseafloor, hydrothermal convection systems that conserve heat and mass and concentrate hydrothermal precipitates are extremely localized by anomalous physical and chemical conditions relative to nearly ubiquitous low-intensity hydrothermal activity at and flanking seafloor spreading axes at all spreading rates. Two distinct shapes of volcanic-hosted

Jan 1, 1989

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By C. R. Pearce, B. Murton, S. Howarth, P. Lusty

"With the expansion of “green” energy technologies, the demand for the critical raw materials required to sustain this growth is increasing. Many E-tech elements, including tellurium (Te) and rare earth elements (REEs), suffer from high supply shortage risk and the need for more diversified metal supply routes is driving research into alternative resources. Hydrogenetic ferromanganese crusts, seafloor deposits of Fe- and Mnoxyhydroxides that form from the direct precipitation from seawater, present a potentially important future source of E-tech elements. With growing interest in the potential wealth of these deposits and the issuing of permits for deep-sea mining and exploration, more work is underway to understand the nature of ferromanganese crust deposits, their elemental concentrations and distributions, and the potential impacts of mining activities.This research focusses on the formation of ferromanganese crust deposits and processes that control the extreme enrichment of elements such as Te, Co and REEs. The crusts were systematically sampled and mapped between ~ 1000 – 4000 m depths using ROV ISIS, from a range of environments, substrates and morphologies from Tropic Seamount (NE Atlantic) in order to determine the seamount-scale factors that control major and trace elemental concentration variations. These factors include depth, surface roughness and micro-bathymetry, location relative to long-term mean current direction and energy, influence of tidal energy dispersion across the seamount, sediment supply, substrate lithology, biological productivity and phosphatisation. The study analyses trace-element characteristics of 100 ferromanganese crust samples alongside standard reference materials NOD-A-1 and NOD-P-1 (US Geological Survey manganese nodules). At this initial stage, we report results from whole rock acid digestion and ICP-MS analyses."

Jan 1, 2017

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By Persifor Frazer

INTRODUCTION For various reasons I have not specified the locality where the research indicated in the following pages was undertaken. It will suffice to say that it was on the grounds of a villa once remote from, but now completely surrounded by, its neighboring city, and in close proximity to an industrial establishment of great extent and importance manufacturing many kinds of steel articles and employing upwards of thirty chimney-stacks for power and process work. The problem was to discover the cause or causes of the mortality to trees and plants on the place, and to trace these causes to their origin. Before undertaking this experimental work, the bibliography accompanying this paper was compiled and studied. It appears from an examination of the careful scientific work performed by the ablest French, German, and English chemists during the last 25 years that they are unanimous in assigning the principal-in fact, the overwhelmingly predominant-cause of the destruction of vegetation to sulphur oxides, resulting either from direct- oxidation of sulphur in oil of vitriol works, etc., or from the oxidation of the sulphur from the minerals associated with commercial coal. Schröder and Schertel showed in 1884 that the sulphates deposited upon the leaves are not injurious to the plants; and Freytag proved that free sulphuric acid could not be found

May 1, 1907

By John T. Awald

The efficiency of search for porphyry copper and molybdenum deposits can be greatly increased. A model exploration system is here presented to show how geologic literature data and field surveys can be aided by modern statistical and computer methods. Assuming that major ore deposits occur in clusters, it is possible to evaluate rapidly large areas at modest cost and with minimum investment risk. An example of the success of these methods is given. Clusters of mine density and metal production covering the State of Nevada were plotted and machine contoured. Selection of a 47,300 square-mile area on the Nevada-California border was made. Within this area, detailed analyses were performed, and a 3000 square-mile site was picked for subsequent field examination. To initiate efficiently the field work, 81 stream sediment geochemical samples were collected and analyzed for copper, zinc, and molybdenum. These data established local variance and necessary statistical controls. Following this, a total of 151 geochemical samples were used to survey the 3000 square-mile area. Computer contouring of results directed attention to specific target areas for detailed geologic analysis, property acquisition and drilling. A total of 22 copper-zinc and molybdenum anomalies were identified. Four of these were recommended for further exploration. To date, two have been acquired and drilled and preliminary ore reserve and financial analysis have been made on one. The estimated cost and time for the regional exploration phases leading to these targets were thirty man-weeks and $16,000.

Jan 1, 1973

By Sirish L. Shah

It is now common to have archival history of thousands of sensors sampled every second over long time. Yet we frequently have process engineers complain:??.We are drowning in data but starving for information??. How can these rich data sets be put to use? This paper addresses the issue of information and knowledge extraction from data with emphasis on process and performance monitoring including fault detection and isolation. Most of the major plant, factory, process, equipment and tool disruptions are avoidable, and yet preventable fault detection and diagnosis strategies are not the norm in most industries. It is not uncommon to see simple and preventable faults disrupt the operation of an entire integrated manufacturing facility. For example, faults such as malfunctioning sensors or actuators, inoperative alarm systems, poor controller tuning or configuration can render the most sophisticated control systems useless. Such disruptions can cost in the excess of $1 million per day and on the average they rob the plant of 7% of its annual capacity. Over the last decade the fields of multivariate statistics and data visualization and analysis methods have merged to develop powerful sensing and condition-based monitoring systems for predictive fault detection and diagnosis.These methods rely on the notion of sensor fusion whereby data from many sensors or units are combined with process information, such as physical connectivity of process units, to give a holistic picture of health of an integrated plant. Such methods are at a stage where these strategies are being implemented for off-line and on-line deployment. This article attempts to outline the field of sensor fusion - the application of signal processing methods, in the temporal as well as spectral domains, on a multitude and NOT singular sensor signals to detect incipient process abnormality before a catastrophic breakdown is likely to occur Keywords: Process analytics, process and performance monitoring, multivariate statistical analysis, sensor-fusion

Sep 1, 2012

By John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closed-loop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermo-mechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermo-mechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

By Kyle Murphy, John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closedloop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermomechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermomechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

Jan 1, 2017

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

By J. Gunaselvam

This article deals with an investigation into the specification and use of appropriate seating systems to reduce whole-body vibration (WBV) exposure in typical vehicles used in the SA mining industry. The EU Directive EU/44/2002 to be legislated in 2005 in European countries, provides legal and economic motivation for this project. The criteria for seat selection can be condensed to the requirements in the directive, which mandates an action level of 0.5 m/s2and a vibration exposure limit of 1.15 m/s2 for an equivalent 8-hour daily exposure period. As part of this study six suspension seats, which the manufacturers claim satisfy the requirements in ISO 70966, were tested to determine the most suitable seat for an articulated dump truck. Six test subjects, three ?light? and three ?heavy? as specified in ISO 70966, were used to estimate the seat transmissibility functions in the vertical direction of the six different suspension seats. Transmissibility functions were measured in the laboratory with two excitation levels of 1 m/s2 and 2 m/s2 r.m.s. in the 0.5?30 Hz frequency range, as well as one spectrum approximating the EM5 spectral class. SEAT values were calculated for road vibration data measured on a typical articulated dump truck. A set of seat selection guidelines that can be followed by vehicle manufacturers and suppliers, procurement officers and and the technical staff on a mine is proposed in this article. It is recommended that additional studies of the use and operating conditions of seating systems in the SA industry, as well as an epidemiological survey be commissioned to gather additional information on this subject. Nomenclature ADT Articulated dump truck DSTF Dynamic seat testing facility EM1 Frequency spectra associated with earth moving equipment (?articulated or rigid frame dumper?) according to ISO 7096 EU European Union ISO International Standards Organisation PSD Power spectral density r.m.s .Root mean square SEAT Seat effective amplitude transmissibility WBV Whole-body vibration

Jan 1, 2005

By J. Ankrum, T. Xia1, D. Wilder, K. Spratt

The human lumbar spine is inherently an unstable structure and requires sophisticated neuromuscular control to maintain its stability and for performing physical tasks. As a consequence, it is important to understand the potential health effects on human operators of mechanical stimuli such as shock and vibration.1 Impact applied to a vehicle operator combines the risk of sudden, unexpected load with the mechanical stress of the seated posture.2 Because many work environments contain the potential for multiple, unexpected impacts, it is important to understand how the trunk muscles respond to complex conditions. We believe the results have implications for isolation design and standards development. Methods Muscle activity was recorded during simple and complex impacts, applied randomly and without warning, while subjects sat on an air-suspension truck seat located on a man-rated 6-DOF motion platform (Rexroth-Hydraudyne). Simple (single) impacts consisted of 100 ms quarter-sine jolts in the side-to-side (L and R) and vertical upward (V) directions with peak amplitude at 0.4 g. Complex impacts consisted of combinations of two simple (single) impacts in sequence (LV, RV, VL, VR), separated by 100 ms. Twelve right-handed males (23.7 ± 7.8 years old) were tested without a blindfold under 2 posture conditions (supported while leaning back and unsupported, sitting upright) and 2 seat suspension conditions (present or absent). Each type of impact was repeated three times under each posture and suspension condition, resulting in 84 impacts in total. Surface EMG signals from the left and right erector spinae (ES), rectus abdominis (AR), external obliques (EO) and internal obliques (IO) were recorded and transformed to 25ms RMS values. The response time, defined as the time the muscle activity exceeded the mean + 2 STD of the pre-impact resting period, peak response amplitude, and time were then derived. A mixed-model repeated measures analysis of variance was used to evaluate statistical significance, where type I error rate was set at .05. Results One question we asked of these data was whether there were differences in responses related to simple single strike impacts (L, R, or V) and complex, double-strike impacts (LV, RV, VL, VR). There are 21 possible combinations of comparisons of simple and complex impacts to each other. The differences found are listed in Table 1.

Jan 6, 2006