Search Documents

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

An iridium oxide coated titanium electrode was tested as anode in copper electrowinning. Initial results confmed that the DSA-type anode was significantly more active for oxygen evolution than traditional lead anodes. However, during longer runs, the anode potential was observed to increase linearly at a rate of 220 mV/year. Scanning elecuon microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the anode passivation could be attributed to elecuochemical dissolution of the coating. The effect on the anode potential of organic additives (glue and thiourea) and lead in solution was also examined. A preliminary economic evaluation of the anodes is given.

Jan 1, 1992

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969

By Henry F. Hebley

INTRODUCTION How often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days" indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer's day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. THE SOURCES OF ATMOSPHERIC POLLUTION The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is probably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominant dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh. Indicative of the stupendous quantities of fuel that are employed in this industrial area's economy, the following (Table No. taken from the U. S. Census (1940) may I of interest. An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, ulti¬mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1948

By Bjørn Nilsen, Brian J. Ballou

The Tellnes open pit mine in Southwestern Norway has been operating since 1960. The maximum height of pit walls is currently about 150 meters with the current mine plan extending this distance to 400 meters with slope stability being a major controlling factor. As a result of unfavorable combinations of directions of major joints and faults, local stability problems have occurred several places in the pits walls. Stability problems have affected the reliability of main transport roads on several occasions. Most of such incidents have occurred during heavy rainstorms and during periods of repeated freezing/thawing. This paper reviews some of the stability problems and the measures taken to deal with such stability problems.

Jan 1, 2006

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By E. H. Griswold

The many complexities arising from our present oil pool proration systems emphasize the need for a suitable standard of property rights. Attempts at conservation and unitization agreements have frequently failed because of the lack of such a standard. The necessity of reducing production to consumption has caused umpires, committees, commissions and other governing bodies to allocate the production of flush fields among the respective owners. The methods of allocation vary widely and conservation of underground reserves is frequently neglected or misused. Critical economic conditions increase, rather than modify, competitive methods. In some fields we have irregular and uneconomically close well spacing. Many operators drill unreasonably large holes, take excessive sand penetrations or leave their wells untubed in order to secure higher potential open-flow tests than their offsets. All of these practices result in economic waste and frequently damage to the pool. Regardless of our agreement with the fundamental principles of proration or unitization, both are actual necessities in many of our present economic situations, and we are in urgent need of a suitable standard of rights to facilitate and simplify their operation. The problems pertinent to unit management are simple and of daily use in many partnership enterprises, but the problems of fair and proper division of production under either proration or unitization are, as yet, subject to controversy. The rights of respective owners must be ascertained and standardized before we can eliminate wasteful practices and still preserve constructive competition in our industry. Valuation of Tracts In a recent unitization conference it was found that each participant had a different basis for calculating the relative values of tracts. Some of these assumptions were as follows: 1. Unrestricted open-flow operation to abandonment. 2. Current proration system to abandonment.

Jan 1, 1933

By C. P. Watson, R. E. Collom

Various chapters already written in the history of development of the North Dome of Kettleman Hills are monotonoysly identical in the one underlying' theme of conservation of oil and gas. Discovered on Oct. 4, 1928, by Milham Exploration Co. with its wildcat Elliot No. 1, the field has been subjected to practically every modern form of production restraint in the name of conservation. The record thus far developed shows that conservation was had for a time, at a price; and that unitiza-tion must be blessed by single ownership or 100 per cent participation to be effective. In fact, incomplete unitization places a heavy handicap upon its participants in the competitive development that follows. Shut-in Agreement of July 25, 1929 Not long after discovery at Kettleman but after the Continental Oil Co. and the Standard Oil Co. had completed several producing wells in the discovery group, came the so-called Shut-in Agreement negotiated at the instance of the Department of the Interior. This agreement became effective July 25, 1929. The fundamental purpose of the agreement was to prevent bringing on production of some 30 wells then being drilled and forestall a flood of Kettleman oil on the market. A cooperative scheme was developed whereby wells in the discovery group would continue to produce. Two of them could not be shut in. Drilling wells would be completed to a water shutoff in top of Temblor and operations suspended. Producing wells would contribute the value of 10 to 25 per cent of their production to the owners of suspended qualifying wells. The percentage rate of drainage contribution was left to a committee or umpire. Some acreage was not placed under the agreement. This same acreage later did not come into the Kettleman Unit Agreement. Several wells on this acreage did not contribute to the drainage fund. The total amount of oil produced during the 17 months of the shut-in agreement, by Milham, Continental and Standard from wells in the discovery group, was 5,297,262.22 bbl. The total amount paid out in "drainage" contributions was $2,046,048.18, representing sales value of 1,266,044.06 bbl. of oil.

Jan 1, 1937

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By Frank Haas

THE public generally has-become aware that there is something wrong with the coal industry and a clamor has arisen for an explanation if not a remedy for this disorder. It is only reasonable that this Institute be looked to for a diagnosis to show the way for some other .agency to prepare the patient for prescription or operation. The subject is extensive, widely diversified, and beyond the efforts of an individual to cover completely; one of the objects of this paper is the initiating of a symposium on the non- technical factors essential to an understanding of the bituminous coal industry. The present condition of the coal industry cannot be described in a few words but, in effect, it resolves itself into a simple statement: The average coal operator is losing money notwithstanding a firm conviction on the part of the consumer that he pays too much for his coal. Without enumerating the many and varied. factors which contribute to this condition, this paper will be devoted to the interrelation of taxation and ownership of coal and its effect on finance

Jan 1, 1930

By Qixing Yang, Björn Haase, Fredrik Engström, Anita Wedholm

"MiMeR, the Minerals and Metals Recycling Research Centre at Luleå University of Technology, Sweden, started industry-related research work to stabilize an EAF slag from Höganäs AB with of CaO/SiO2 values near to 3.2. The intention was to determine the suitability of the EAF slag as construction material after stabilization. Some of the stabilizers effective for preventing disintegration of AOD slag were examined in laboratory tests for stabilization of the EAF slag. The EAF slag samples were mixed together with stabilizers for melting at 1600ºC and then cooling in a crucible system. With a laboratory granulation system, the liquid EAF slag was cooled rapidly using air. Samples from the tests were characterized by different techniques, including XRD and SEM. Some of the results from the work may be useful for preventing slag disintegration and, thus, enhancing utilization of the EAF slag as construction material, thereby saving valuable natural resources.IntroductionAt steel plants of some MiMeR member companies, steel grades with low carbon contents were produced in Electric Arc Furnaces (EAF). EAF slag was tapped out of the furnace to slag pots for transport to slag yards, where the slag was poured on the ground. Very often, the EAF slag disintegrated during cooling on the ground. Fines from the slag disintegration were often difficult to handle and use as material for road construction [1, 2]. The EAF slag disintegration was rather similar to the disintegration occurring in the slag tapped from some AOD (Argon Oxygen Decarburization) converter heats.Literature studies show that formation of dicalcium silicate (C2S) is the main reason for the disintegration or dusting of AOD slag from production of stainless steel [1-4]. The C2S can form while the content ratio of CaO to SiO2 of the slag, CaO/SiO2, exceeds 1.4 [1]. Values of CaO/SiO2 for the AOD slag are often near to 2.0, making the C2S a predominant slag component. The ß phase of C2S, ß-C2S, transforms into its low temperature ? form in the temperature range of 400-500°C, inducing a volume expansion of nearly 12% [1-4]. The volume expansion disintegrates the AOD slag."

Jan 1, 2008

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005