Search Documents

By C. A. Snyders

The research presented in this paper investigated the practical aspects of the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were conducted on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of Pt, Pd, and Au were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours, and 100 per cent for Pt, 97.4 per cent for Pd, and 99.9 per cent for Au after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while Ni concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, Ni adsorbs at approximately the same rate as the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. The equilibrium loading of gold is exothermic in nature (Fleming and Nicol, 1984) which will result in an increase in gold elution kinetics with an increase in temperature at similar pre-treatment conditions. A similar result was found for the elution of Pt and Pd. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and results suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing due to increased ionic strength.

Jan 1, 2013

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By J. McCreedy

The Ontario Division of The International Nickel Company of Canada, Limited, operates five underground mines and one open pit on the rim of the Sudbury Basin located in the Province of Ontario, 230 miles northwest of Toronto. Four of the mines, Frood-Stobie, Creighton, Murray and Garson, lie on the South range of the Basin within a 10-mile radius of the City of Sudbury; the fifth mine, Levack, is on the North range, about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, the principal minerals being pentlandite and chalcopyrite. Other elements recovered from the ores in varying quantities are platinum, palladium, ruthenium, iridium, rhodium, cobalt, selenium, tellurium, iron, sulphur, gold and silver. In 1962, the total underground ore production was over 10,800,000 tons which was mined mainly by blasthole and caving methods with the remainder by cut-and-fill, square set, and undercut-and-fill techniques.

Jan 1, 1964

By M Taylor

The Project Specification and Technical Requirements documents associated with several recent large road tunnel projects within Australia have specified the application of AS/IEC 61508 – FunctionalSafety of Electrical/Electronic/Programmable Electronic Safety Related Systems at very high performance levels for the various control and fire life safety systems associated with such facilities.This paper seeks to explore the implications of referencing this standard within the road tunnel services context in terms of practicality, complexity and cost, whilst providing some examples of how a high safety integrity level (SIL) level can theoretically be achieved given current hardware availability.

Mar 8, 2011

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By R. W. Hammack

Results for the treatment of a problematic mining wastewater using bacterial sulfate reduction (BSR) are presented. Specifically, a BSR pilot treatment plant (250 L per day) was used to treat Berkeley Pit simulant to discharge standards with the selective recovery of separate Cu- and Zn-sulfide concentrates. Concentrates recovered in these tests contained greater than 50 % of the target metal and met specifications for sale to existing smelters. The biological component of the treatment was found to be surprisingly robust. Scaling and solid/liquid separation problems were encountered but considered normal for sulfide treatment. For Berkeley Pit water, capital costs for BSR treatment was found to be comparable to high-density sludge lime treatment. The value received from the sale of recovered copper ands zinc concentrates paid for all the operating costs.

Jan 1, 1999

By David A. Smith

A new generation of reliable, stable, and easy to use bulk emulsions allowing application in tunneling and drift rounds has been developed. This new product group of bulk emulsions has been especially formulated for use in small-diameter holes and is a significant advancement in bulk emulsion technology. Reliable and easy-to-use bulk delivery equipment has been designed and developed to allow bulk emulsions to be used in a wide variety of shaft and tunneling applications.

Jan 1, 1987

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By L. A. Harris

In the present study the open gradient magnetic separation' (OGMS) method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy (SEM) and x-ray diffractometry (XRD) were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (-80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

Jan 1, 1981

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By R. Farnfield, W. Birch

Arguably, some of the most restrictive statutory blast vibration requirements attached to mineral extraction operations can be found in the United Kingdom. Such limitations are, as a rule for the UK, stipulated together with a required statistical confidence that has to be observed in the blast design process in order to ensure total planning compliance. A key element in this procedure is the effect imparted by vibration data scatter from previous blasts as this becomes reflected in the site’s operational standard error statistic and in turn directly influences the maximum instantaneous charge weights that can be justifiably employed. The greater the scatter, the lower the compliant charge weights become.

Jan 1, 2006

By L. Z. Li

The application of some environment-friendly mineral processing technology was introduced in Xitieshan lead?zinc mine and Hugary copper mine of China Western Mining Co., Ltd, located in western plateau area where the ecological environment is extremely fragile. The results of the significant economic efficiency were obtained by applying these new techniques while the protection of peripheral environment and the improvement of ecology were made.

Jan 1, 2014