Search Documents

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By K. Lillkung

The use of secondary sources has become a very attractive option in the production of platinum group metals as the demand for these metals has increased. One of the promising sources are the spent catalysts, which provide an attractive source as they have relatively high metal content compared with the ores where the metal is originally extracted from. The concentration of platinum group metals in catalytic converters is in the range of 0.1-1 mg/g as the concentration in ores is usually less than 10 ppm. Aqueous chloride solutions are claimed to be a cost effective way in which platinum group metals can be brought into solution and concentrated. In this work the effect of different parameters on the dissolution rates of Pt, Pd and Rh were investigated. The parameters investigated were the Cl- concentration, the temperature and applied potential. Chloride concentrations used were 62.5, 90, 125 and 250 g/l. Temperatures were 25, 40, 60, 80 and 94°C. Potentials were 950, 1050, 1150 and 1250 mV vs. SCE for Pt and Rh and 380, 410, 440 and 470 mV vs. SCE for Pd. Dissolution rates were calculated from the current densities determined by potentiostatic measurements. Thin wire electrodes were used in the measurements. As expected, higher temperature, higher potential and higher chloride content generally increasedthe dissolution rate. However, the effect was nonlinear and slightly different for different metals. The results show that strongly oxidizing conditions are needed in order to achieve reasonable dissolution rates. With the highest chloride content and at potential of 1250 mV vs. SCE and 94°C the dissolution rate of Pt was nearly 1 mm/h, whereas in similar conditions Rh achieved a rate of only nearly 100 µm/h. Similarly, with the highest chloride content and at potential of 470 mV vs. SCE at 94 °C the dissolution rate of Pd was nearly 1 mm/h. Keywords: Pt, Pd, Rh, redox potential

Sep 1, 2012

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002

By H. M. Howe

THIS paper presents an experimental verification of some of the predictions made by one of us' concerning 'the influence of certain conditions of casting upon the size and position of the pipe', and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following A. That the pipe is shortened and the segregate raised 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last freezing-part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis ; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jul 1, 1907

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

By Jay. M. Khodadadi, Josef Štetina, František Kavicka

"With the aid of the proper original numerical model of solidification the instruction for preparation of input parameters for numerical simulation of technological processes, with change of the phase or structure, will be presented. A method of calculation analysis of influence of therrpophysical properties of materials entering the system of casting-mould-cores environment, and also of boundary conditions on the required simulation accuracy will be suggested. For the cast material, the influence of heat .conductivity, specific heat capacity, density and latent heat of phase transformation also has been analysed. For metallic or non-metallic moulding material"" the influence of the see main parameters has been analysed and, furthermore, their combination, influence of thermal conductivity, and of heat storage. The order of influence of all quoted parameters of a casting and moulding material was established. For example heat conductivity in the liquid state is on the last place. From the boundary conditions the -most important influence on the total solidification time and · on the mechanism of forming of temperature field has the ·boundary condition on the casting mould boundary, then follows the boundary condition on the level of a molten metal. The negligible influence has the boundary condition on the mould frame and on the bottom.IntroductionThe original and universal mathematical model of solidification, cooling and heating has been set up and checked, in order to be capable of analysing a one- to three-dimensional steady or unsteady temperature field of the casting-mould-environment system and, namely, of the system as a whole or its arbitrary parts, during any industrial technological process whose individual processes could be solidification, cooling, heating, refrigeration and others, in any sequence or singly. The model enables the simulation of traditional and also non-traditional technologies of casting in foundries, metallurgical plants, forging operations, heat treatment processes, etc. If solidification is not the matter, the metal part of the system need not be called the casting but a component, a block, a forging and the like."

Jan 1, 2000

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By Daniel Stickel

Current political, economic and ecological guidelines demand the increase of power densities of nearly all machinery parts today. In order to further lower the wear rate towards the ultra-mild sliding wear regime an integral approach is needed, which has to regard contact conditions, surface topography, surface chemistry, as well as sub-surface properties. Still there are no simple parameters to classify the performance of tribosystem. In this study the area and volume affected by tribocontacts are calculated by means of a three dimensional elastic-ideal plastic contact model. The surfaces are generated by means of conventional machining procedures and characterized by scanning white light interferometry. The further input data as to normal and friction forces are derived by ultra-mild sliding wear tests under boundary lubrication conditions of carburized steel against carburized steel and 52100 steel against case-hardened spheroidal cast iron. This contribution will depict the distinct influence of the topography on friction and ultra-mild sliding wear of common Fe-base materials and point on the marked importance of highly localized effects, which govern the acting mechanisms.

Jul 31, 2018

By J. Grobler, J. Zietsman

"Understanding the influence of feed material mineral assemblage on spiral separation is paramount for the successful and consistent operation of a spiral plant. Plant stability is required to maintain high recovery of valuable heavy minerals (VHM). Standard material analysis methods used in the heavy mineral industry to evaluate spiral separation behaviour are unable to quantify performance differences in the case of large variations in feed assemblage. This study illustrates a systematic approach to evaluate spiral separation performance. This technique was applied on a four-stage spiral plant. The performance information was used in a circuit simulation to clearly illustrate the importance of correct setting of the spiral splitter position and resulting spiral mass loading to ensure optimal circuit stability and maximum VHM recovery.IntroductionHeavy mineral sands deposits generally consist of naturally fine-grained, free-flowing sand due to the way in which the deposit was formed. The size of the heavy minerals market is roughly 8 Mt/a of zircon and titanium combined (Iluka, 2013). If an average combined feed grade of 5% zircon and titanium and an average combined overall product recovery of 80% are assumed, the resulting run-of-mine feed tons that would require primary spiral beneficiation is 200 Mt/a. The number of spirals required for the processing of this material, assuming 6500 operating hours per annum, an average of 2 t/h per start, and the same number of rougher spirals as other duty spirals, is over 30 000 spirals for the heavy mineral sands business alone. These numbers clearly illustrate the importance of the spiral in the heavy mineral industry.The aim of a spiral plant in the primary processing value chain of a heavy mineral process is to reject non-valuable quartz (a light mineral) from various valuable heavy minerals (VHM). The product from the spiral plant is a heavy mineral concentrate that has a reasonable grade (more than 90% heavy minerals) at a reasonable heavy mineral recovery (greater than 90%). This benchmark is fairly easy to achieve if all the mineral particles are well liberated (as in the case free-flowing sand), the feed is properly deslimed (-45 µm fraction removed to less than 5% of the solids mass), and the spirals are fed within design solids concentration (water to solids ratio) and design spiral load (dry tons per hour per start)."

Jan 1, 2017

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The influence of two weeks of microclimate cooling on the state of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, M.Sc. (Potch.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Five volunteer Black subjects were acclimatized according to the climatic-room acclimatization procedure, and their states of heat acclimatization were determined by the usual heat-stress test. The subjects thereafter wore pre-frozen jackets in a somewhat higher environmental temperature (33,9/35,6 °C). stepping at the same rate as before for four hours a day for fourteen days. The heat-stress test was repeated and followed by a similar test at the higher environmental temperature. It was found that fourteen days of microclimate cooling in a very hot environment had no adverse effect on the degree of heat acclimatization. The sweat rates during microclimate cooling remained high, even though no sweating is possible beneath the pre-frozen ice-jacket. which indicates that there is an increase in sweat rate from the areas of exposed skin.

Jan 7, 1975

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

As students progress further into a degree, the decision of vocation selection, and even more importantly û securing employment in a particular industry sector, can become quite daunting. However, with a little initiative, students can overcome these issues by not only researching what employment opportunities exist, but by applying for summer vacation employment. Undergraduate vacation employment, especially with a world-leading hydrometallurgy research organisation such as the Parker Centre, can dramatically alter a studentÆs perspective of particular industries and possibly even alter their selection of vocation pursuits upon graduating. Students can also use vacation employment to enhance their networking capabilities, technical skills and knowledge by dealing with challenging new topics such as sulfur dioxide leaching, which is also discussed in this article.

Jan 1, 2005

By Robert Abbott

THE influence of various elements in retarding or accelerating the absorption of carbon during the process of carburization is fairly well known. In general those elements which forth carbides accelerate the absorption, while those which do not retard it. It has sometimes been wrongly stated that those elements which raise the temperature of the critical range increase the absorption, while those which lower this temperature decrease it. Silicon is a notable exception to this rule, for its influence is to raise the critical range but to lower the absorption of carbon. Some elements which do not form carbides have no apparent influence upon the absorption rate. Carbon itself retards the absorption rate. With a view to obtaining more exact data upon the subject the following experiments were undertaken : 208 steels of different chemical composition were selected to represent most of the types of modern constructional steels. Specimens 3 in. in diameter and in. in length were weighed to milligrams. They were then packed in the special carburizing box shown in Fig. 1, and kept in .the furnace for 10 hours at a temperature of 900° C. A duplicate experiment was conducted at 1,000° C. At equal' intervals of time the box was rotated in the furnace so that. two complete revolutions were made in the 10 hours. This precaution was taken to neutralize as much as possible any effect of unequal heating. At the end of the 10 hours the box was allowed to cool in the furnace with the doors open. The specimens were then weighed again and the increased weight (carbon) determined. In. the following table are given the analyses of the various steels, together with the. increased weight of .carbon expressed in milligrams.

Jan 10, 1913

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By Błażej Doroszuk, Robert Król

Mill drums are essential equipment in various industries for the comminution of materials. To optimize their design and operation for efficient and cost-effective processing, it is necessary to understand the behavior of the mill drum under various operating conditions. This study investigates the behavior of a mill drum using a combination of experimental and numerical methods. The factors that can influence the behavior of the mill drum, such as the size and shape of the mill, grinding media, rotational speed, filling level, and material properties, are discussed. Experimental methods can be limited in obtaining measurements of internal processes, so numerical methods such as the Discrete Element Method (DEM) are also used to simulate the behavior of the mill drum. In this study, the experimental measurements of the motion of the grinding media are obtained using computer vision methods, and the numerical simulations are calibrated using the experimental results. A designed experiment approach is used to evaluate the performance of the mill drum under various operating conditions. The results of this study can be useful for the design and optimization of mill drums to achieve better performance and energy efficiency.

Jun 25, 2023