Search Documents

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By Robert F. Kehrman

As part of the Bureau of Mines research on the In-Situ Uranium Leaching, various geophysical resistivity measuring techniques were -evaluated to identify a rapid reliable method for detecting the underground migration of lixiviant outside of the planned limits. Surface and downhole galvanic resistivity and controlled source audio-magnetotelluric (AMT) methods were tested at an in-situ uranium mine in Northern Wyoming during start-up of a new mining area. Downhole galvanic and AMT were the most promising techniques.

Jan 1, 1980

By L. B. Phelps

Many coal mining companies have potential surface mine reserves which either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1985

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

By R. G. Bradburn

"Brenda Mines Limited is a low grade open pit mining and milling operation located near Peachland, British Columbia. The mill was brought into production in late 1969 at a rated capacity of 24,000 tons per day. Tt currently treats an average of 30,000 tons per day of an ore that has an average grade of 0.130% copper and 0.030% molybdenum.Description of Crushing and Grinding CircuitsRun of mine ore is delivered to a primary gyratory crusher. The minus seven inch product is separated into plus and minus one inch fractions on two parallel vibrating screens. The fine product is conveyed directly to the mill fine ore bins, while the coarse fraction is sent to a 45,000 ton stockpile.Material from the stockpile is fed to two standard cone crushers which operate in an open circuit with five secondary vibrating screens. The minus five-eighth inch product from these screens is conveyed to the mill fine ore bins while the coarse fraction is fed to four shorthead cone crushers. These crushers operate in closed circuit with the screens."

Jan 1, 1981

By Dennis F. Koschak

Production tests at Reserve Mining Company's iron ore pelletizing plant established that rubber-lined balling dm produce a green pellet equivalent in quality to those produced in conventional balling drums equipped with reciprocating cutter bars. The flexing action of the rubber liner prevents concentrate buildup in the drums, eliminating the need for a cutter bar. Advantages of the rubber-lined drum includes a reduction in maintenance and operating manpower, reduced bentonite consumption with less drum surging, reduced power consumption, and improved drum on time.

Jan 1, 1983

By Thomas A. Simpson

Heretofore, underground coal mines in Alabama have operated under only 60 to 360 meters of cover: however, new mines (at least 5 in the early opening or development stages) will be operating under cover ranging from 600 to 660 meters. With increased rock confining pressures, roof stability problems will become more critical. Initial studies in two 7 ½ -minute quadrangle areas in the Warrior coal basin of Alabama indicate that the orientation of certain lineament and fracture-trace modes mapped from ERTS-1 (Earth Resources Technology Satellite) imagery correlate closely with the strike of joint and fault modes. High altitude (118,000 m) U-2 aircraft data were used to support these findings. In addition, over 50 percent of the normal faults mapped in the study area could be directly correlated with ERTS and U-2 lineaments and fracture traces. These correlations provide clues to the structural development of the Warrior coal basin and may, in turn, be used as a guide to the prediction of roof-stability conditions in advance of mining.

Jan 1, 1975

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By R. Latifovic

Assessment of the possible impact of existing and future mining projects located in remote areas may be difficult and costly. This may have an adverse effect on the process of issuing mine permits and development of new mines. A remote sensing based land cover change assessment methodology presented in this paper is a promising avenue to render this process more meaningful, precise and affordable. It has been applied to a case study of the Oil Sands Mining Development in the north-east of the Canadian province of Alberta. Recently, the Athabasca Oil Sands Region (AOSR) is a place of unprecedented growth of open-pit mining operations. This study was focused on the primary impact onto the landscape and vegetation resulting from exploration and, mining development. This impact was assessed using an information extraction method applied to two LANDSAT scenes. The analysis based on derived land cover maps shows a 8.64% decrease of natural vegetation in the study area (715,094 ha) in 2001 relative to 1992. It is demonstrated that the methodology presented here provides reliable results and is fully applicable for the assessment of the environmental impact of large scale mining operations.

Jan 1, 2006

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By D. K. Denton, M. J. Friedel, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep ( > 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Feb 24, 1997

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By William E. Horst, John H. Bassarear

A technique is described which simplifies the standard procedure for measuring the Bond work index of a specific ore and illustrates how to overcome the strict requirements regarding feed size distribution normally encountered in operating plants. Actual results obtained from various process streams in a copper concentrator are presented and the grindability data are discussed in relation to the observed plant performance. This type of information can be used to gain a better understanding of plant behavior and to assist in the evaluation of plant modifications and process control studies.

Jan 1, 1977

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By J. H. Slater

THERE is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust con-tains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out, This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage, An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable prod-uct, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates.

Jan 1, 1940

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967