Search Documents

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer's correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer's instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By W. S. Sadik

This paper presents the ventilation design for an underground testing facility in a salt medium. The underground workings consist of two-12 ft. (3.66 m) diameter watertight shafts and approximately 6000 ft. (1830 m) plus of drifting. These facilities are designed for the purpose of providing access for an in-situ testing of a salt horizon in which a variety of hazardous and non-hazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1988

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By A. S. Richardson

THE conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Co. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on. The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are : heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 2, 1922

By Leonard Sargeant

The Pocahontas Coal Field consists of eight mineable seams of low-volatile coal in southern West Virginia and Virginia. The deeper seams, especially the Pocahontas No. 3 and No.4 Seams, under heavy cover and below drainage are notoriously gassy. Methane in the Pocahontas Field is generally thought of as being confined in the coal itself, rather than in mud slips or clay veins. Furthermore, it is characteristic of Pocahontas coal to retain its gas until the coal is broken and removed from the solid. Because of this inability for gas to escape from unmined coal, entries developed around large blocks are seldom of significant value in bleeding off methane before pillar extraction begins. This is evidenced by the fact that it is not uncommon to find gas liberated during the mining of chain pillars and barriers which have been developed for several years. The Pocahontas Fuel Company develops almost all solid coal by conventional methods with shuttle car haulage. To provide the maximum productive capacity without compromising ventilation and safety requirements, the Company has adopted standards for ventilating 5, 6 and 7-entry sections.

Jan 1, 1960

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By Charles A. Mitke

Discussion of the paper by CHARLES A. MITKE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1941 to 1958. GERALD SHERMAN, Bisbee, Ariz.-Mr. Mitke justly might have made much stronger his claim for increase in efficiency of labor due to the introduction of forced ventilation. The product per man shift in stoping in the Gardner division has practically doubled. While it is true that improved methods have been responsible for a great part of this gain, and what is due to better ventilation cannot be definitely known, yet it is also true that the results could not have been obtained in that division as it was in 1912. . The paper discusses the two systems of ventilation in use, exhaust and pressure. In both the object is the same, to take foul air or gas out of the mine by the most direct course and replace it by fresh. In coal mines, the exhaust system is in almost universal use, and since the most advanced work in ventilation has been in that class of mines, it was naturally the first one to be considered. It has the advantage of leaving all adits, shafts, or other openings free for use. Doors are only needed to direct the course of the air, and not to confine it. Its disadvantages appear in case of fire, or if the ground over the mine is much broken by subsidence. The fan must work in gas in the case of a -fire, and may be. damaged or destroyed either by heat or by corrosive gas. At the time of the fire in the Lowell division of the Copper Queen, a small exhaust fan was placed over a ventilating raise, but the vanes and housing were destroyed by sulphurous gases within a few weeks. If the ground above the mined area is much broken, as is frequently the case when the ore deposit is thick vertically, a good deal of air is likely to pass through it, particularly if it is near the surface. Leakage from this source is a loss to the exhaust system by short circuiting, which is exaggerated by a contraction or block in the air course. It serves as an added outlet in the pressure system. This is strikingly shown at the United Verde, where many jets of steam may be seen coming up through the ground above the stoped country on a cold day.

Jan 12, 1915

By R. D. Parker

Location The Frood ore-body is expressed on surface as a prominent gossan ridge, with a total length of approximately two miles. The original Frood (the old No. 3 mine of the Canadian Copper Company) is at the southwest end of this gossan; adjoining it on the northeast is the Frood Extension (until 1929 the property of i:he Mond Nickel Company), while at the extreme northeast end is the Stobie mine. The first two of these divisions of the ridge form the Frood mine as it is known today.? This lies in lots 6 and 7 of the sixth concession, township of McKim, and is two and a half miles north of the city of Sudbury. The general elevation is 1,000 feet above sea level. The Ore-Body The Frood-Stobie parallel offset(l), as its name implies, has no connection in the field with the main mass of the Sudbury nickel eruptive-a norite. It lies one mile to the southeast of that body, and, in general, parallels it in strike. The ore occurs as a more or less tabular structure in what is known locally as the Sudbury series. They are the oldest rocks of the district, and have been placed by Collins(2) as earlier than the lower Huronian, of pre-Cambrian time. The series is comprised of sediments, volcanics (both acid and basic flows), tuffs, agglomerates, breccias, and basic intrusives, all highly metamorphosed, yet all forming a more or less regular picture. The controlling feature of the area has been the attitude of the sedimentary strata, from which has arisen the present sill-like character of the flow rocks, the basic intrusives, and the ore-body itself.

Jan 1, 1932

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By F. T. Cawood, T. Chikande, H. R. Phillips

Underground mines require electricity to operate both the main surface fans and auxiliary systems, with primary ventilation systems typically accounting for approximately 40–60% of the mine’s overall electricity consumption. The primary reason for this considerable expense is that most underground ventilation systems are designed for peak demand, regardless of the actual demand, which is commonly dictated by diesel equipment usage in trackless mining operations. Most platinum mines on the Great Dyke in Zimbabwe tend to operate their ventilation systems at this peak level, despite the mine’s air quantity being well in excess of the ‘true’ ventilation needs. This is due to a lack of appropriate ventilation controls. The authors designed and installed a ventilation-on-demand system at one of the bord and pillar platinum mines to minimize the use of redundant air in underground operations. Fourth industrial revolution techniques were applied to the environmental monitoring and tracking systems thereby optimizing air quantity demands. The mine managed to reduce its annual power consumption by 23% through the implementation of manual control and time-of-day scheduling levels of the ventilationon- demand concept. There was also a 6% productivity improvement, mainly attributable to an increased face time as a result of the significant reduction in the re-entry period following a blast. This paper introduces a novel concept of ventilation optimization through digital transformation targeting mainly room and pillar platinum mines. A system was designed, installed, and commissioned, though there is currently an ongoing optimization process to harness the full benefits such as productivity enhancement, reduced power costs, and improved worker health.

Dec 13, 2022

By M Tessier, M Pahkala, L Sletmoe

The Red Lake mine is one of the richest gold mines in the world. The primary mining methods are overhand and underhand cut and fill. Starting in 2003, Goldcorp initiated an expansion program at the mine. The expansion includes a new 6.55 m diameter hoisting shaft currently under construction. The shaft will be driven to a length of over 2180 m. The shaft will be used as a primary ventilation intake to the mine. In addition to the new hoisting shaft, a return air raise is being driven approximately 1690 m from surface. This raise will be a parallel return to the existing mine infrastructure. This paper describes the ventilation and climatic analyses performed in support of the expansion project. The study included a full mine ventilation survey, in situ rock mass measurements, analysing options related to mine layout, airway sizing calculations, air heating options, and climatic simulations. Specifications were prepared for an air heating system and main and booster fans. Analyses were also performed related to heat in the stoping areas namely caused by auxiliary fans and backfill with high cement content.

Jan 1, 2005

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Keith G. Wallace

In 1982 the U.S. Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: 1) A site in volcanic tuff located at Yucca Mountain in Nevada, 2) a site in bedded salt located in Deaf Smith County in Texas, and 3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval.

Jan 1, 1987

By Archie M. Richardson, Carl E. Brechtel, Tom R. Kelly, Frank Feero

Recent work to upgrade the ventilation system for the el Mochito lead/zinc mine in central Honduras is discussed. Network modeling and underground measurements were used to evaluate cost-effective alternatives for achieving satisfactory ventilation in a complex and expanding underground operation. Both interim and long-term solutions were implemented to make mining possible under difficult conditions. INTRODUCTION Mining operations at the el Mochito Mine, located in the central highlands of Honduras, Central America, have been virtually continuous since the opening of the mine in 1948. Initially a high-grade silver mine, the mine has expanded along a westward trend of pipe-like orebodies to a distance of roughly one mile from two centrally located shafts. Production of the relatively large San Juan orebody at the western most extension of the mine (Paddock, 1981) led to the introduction of diesel-powered equipment; however, the ventilation infrastructure was insufficient to meet the needs of mechanized mining. A succession of owners/operators in the 1980s allowed the existing ventilation infrastructure to decay to the point that ventilation in the production areas of the mine was very poor. Environmental conditions in some working areas were not conducive to efficient ore extraction because of high dry bulb temperature, high humidity, and diesel emissions. Upon acquiring the mine in 1990, Breakwater Resources of Tucson, Arizona began an aggressive program to refurbish the mine infrastructure to complete extraction of the San Juan orebody and to allow the extension of the mine another 2500 ft to the west for extraction of the Nacional orebody. The program included increasing the capacity of the main ventilation system. This article presents a case history of the process of upgrading the ventilation system in a mine where extensive old workings cause large air leakage. This process has been one of selecting solutions to difficult technical problems that are compatible with the existing mine infrastructure and economic constraints. The initial ventilation system is described in the background section, along with ventilation projections for the mine expansion. Field characterization of the ventilation system for design verification and fan specification is then discussed. The paper describes a series of interim changes to the system to improve ventilation pending completion of new ventilation boreholes. In addition, the temperature/ heat problems in the mine are described. BACKGROUND Initial Condition of Ventilation System The ventilation system is illustrated in Figure 1, which shows the extent of mining with the main ventilation paths superimposed. Early mining around the two shafts opened up vertical connections (stopes and raises) over the entire 2420 ft (737.6 m) of vertical extent, and mining progressed to the west primarily using compressed air and electric-powered equipment. Since ventilation was not a complex problem in the original mining system, the stopes and interconnecting raises were not sealed. The San Juan orebody was much larger than the silver ore zones mined previously, being primarily zinc and other base metals. Its geometry, size, and grade allowed the use of vertical crater retreat (VCR) stoping with diesel mucking and haulage equipment. Its depth, along with the existence of warm groundwater, resulted in a mine climate problem on the lower levels. To establish a complete ventilation circuit, two vertical boreholes (Bonanza Nos. 1 and 2) had been drilled by previous owners from the surface in the vicinity of the San Juan orebody. The system design called for air to be drawn down the intake shafts, across the lower mine levels to the San Juan workings, then up through the San Juan ramps and ore passes to these two exhaust boreholes (see Figure 1). In practice, however, only the Bonanza No. 1 borehole was drawing air through the desired path. Leakage across the old upper levels from the intake shafts, the Caliche tunnel, and from intervening abandoned stopes and raises supplied most of the air flowing to the base of the Bonanza No. 2 borehole. In effect, there were two ventilation circuits in semi-parallel through the mine, of which only one was delivering appreciable air to the San Juan workings.

Jan 1, 1993

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983