Search Documents

By G. Landry

"IntroductionThe Cape Breton Development Corporation (CBDC) is constantly searching for new technologies that will enhance the marketability of its coal. One technology which shows promise in utilizing Cape Breton coal while at the same time addressing the traditional problem of high sulphur inherent in the Sydney coalfield, is coal-water fuel (CWF).The CWF process incorporates a physical change of coal by grinding it to a flour-like consistency and then mixing additives with it to make a fine coal slurry. The result is a liquid dispersion of fine coal particles that looks like oil, stores and flows like oil but burns like coal. The equipment used in the CWF process is standard mineral processing equipment but application of the equipment to manufacture a specific coal particle size and the specified additives used in the mixing make it a unique technology.The product, which CBDC calls Carbofuel, consists of 70% coal, 29.5% water and 0.5% chemical additives. The key properties of the product are: (I) high solids loading, (2) medium viscosity levels, (3) stability against sedimentation, and (4) good atomization behaviour. Carbofuel specifications are presented in Table I. Carbofuel ProductionThe production of Carbofuel is based on the controlled processing of coal. This involves wet grinding of the coal to a specified fine size (-250 um), cleaning this fine product to remove mineral impurities and formulating (with chemical additives) a finalproduct from the cleaned coal. The flow diagram in Figure 1 indicates the processing circuit for Carbofuel production.CBDC operates a 7-tonne-per-hour continuous production plant complete with state-of-the-art control, full laboratory services, product storage and loadout facilities. The plant has operated since 1983 and has produced over 12000 tonnes for several major demonstrations. The plant is shown in Figure 2."

Jan 1, 1987

By W. R. Boehme

The laboratory test work compares various 6 x 16 mesh activated coconut carbons using a gold standard solution of 4 ppm dissolved in sodium cyanide. The carbon adsorption rate and maximum loading are measured for different feed solution ionic contaminates: silver, copper, thiocyanate, and ferrocyanide. Conclusions are drawn that among the activated coconut carbons tested, maximum loading and the effects of specific ions varied significantly. The work presented can be applied to 6 x 16 mesh carbon selection tests and specific ion monitoring for industrial carbon adsorption systems.

Jan 1, 1984

By J. Bullón, A. Pérez

Some years ago, Ferroatlantica developed a new type of electrode known as the ELSA electrode. In this electrode there is a central graphite core that provides support, surrounded by an annulus of Søderberg paste that gets baked during operation. This technology has been implemented on several silicon furnaces around the world, and was reported on during the previous Infacon conference. In all electrodes, but particularly in the ELSA electrode, the quality and consistency of the paste are important for correct operation. As the type of paste varies between customers and between countries, Ferroatlantica has developed a quality control procedure for their customers of this technology. This procedure is geared to the point of view of the customer rather than the paste producer. The analysis is based on the desired flow pattern of the raw paste and on the desired mechanical and electrical properties of the baked paste, as experience has shown that these are the most important parameters to monitor in order to avoid having problems with the resulting electrodes. This paper discusses these methods of paste analysis in the light of complementary studies that have been done when there has been an electrode breakage in the different plants.

Jan 1, 2007

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By Harold Potter

(1) A great deal of experimentation has been carried out by the Wet Process Cement Manufacturers in connection with additives which make possible the production of a pumpable slurry at reduced moisture contents. We ourselves have made dozens of tests both at Laramie, Wyoming and Monolith, California. (2) The viscosity or pumpability of a slurry at a definite moisture content and fineness seems to depend on two basic phenomena. One is the physical structure of the raw material itself, which on fine grinding may or may not be excessively hydrophilic (water adsorptive). Usually crystaline or glassy raw materials are non- hydrophilic. The fine grained amorphous raw materials such as shales and clayey limestones very frequently are, however. (3) The second basic phenomenon affecting the hydrophilic tendencies of the raw material is the presence of certain soluble salts, especially gypsum and small amounts of alkalin carbonates or oxides. (4) Various soaps, and phosphates can be used to produce a pumpable slurry of low moisture content when using hydrophilic raw materials as well as can other proprietary materials such as certain long chain carbon compounds. Too frequently however, the price of such additives in conjunction with the amount required prohibits their use in the cement industry.

Jan 1, 1959

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation was investigated as a process to convert gaseous CO2, into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results were achieved using heat-pretreated serpentine feed material and a high partial pressure of CO2 (Pc02). Specific conditions include 155°C, PC02 = 185 atm and 15% solids. Under these conditions, a 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy was utilized to investigate the appropriate feed characteristics, identify the process products and interpret the mineral dissolution and carbonate precipitation reaction paths. Key words: Mineral carbonation, Carbon dioxide sequestration, Carbonates

Jan 1, 2003

By G H. Park, Y J. Jun, J H. Park

The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag, the main system formed in the Ruhrstahl-Heraeus (RH) vacuum degasser, was measured at 1873 K to understand the effect of slag compositions on the carbon contamination in the ultra-low carbon (ULC) steels. The stable form of carbon was demonstrated to be carbonate by plotting the log [(wt%C)/aC] ratio against the log p(O2) which ranged -11 < log p(O2,atm) < -9. The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag can be estimated using thermodynamic model. The distribution ratio of carbon increased with increasing concentration of FeO due to the FeO reduction reaction and increased basicity of slag. The carbonate capacity of the CaO-Al2O3-FeO-SiO2-MgO slag can be expressed as a linear function of the activity of lime and the optical basicity.

Jun 19, 2024

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By V. Nasri, P. Jarast, M. Bakhshi

The Montreal metro Blue Line Extension toward the northeast consists of the construction of five new underground stations. The project includes 6 kilometers of the tunnel which will be constructed using a Tunnel Boring Machine (TBM). In line with the commitment to integrating sustainability best practices, Envision verification is pursued this project. The Envision reference framework was developed to cover all the sustainable development aspects of an infrastructure project and each phase of its life cycle (planning, design, construction, operations and maintenance, and end-of-life). As a part of this endeavor, low-carbon concrete and shotcrete mixtures are proposed for the linings of TBM and SEM tunnels as well as stations and auxiliary structures. The CO2 emission of the low-carbon concrete and shotcrete mixtures were compared with their typical mixtures and the total CO2 emissions reduction related to the tunnel lining is determined. The study is of strategic significance for achieving emission reduction in the tunnel industry.

Jun 13, 2023