Search Documents

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894

By Henry M. Howe

This paper may be regarded as a report of progress of an investigation into the influence of prior exposure to different high temperatures, under different conditions, on the properties of steel after it has been cooled completely. The following are the chief divisions: II.—Experiments on toughening manganese-steel by sudden cooling. III.—A study of the critical points of common or carbon-steel, chiefly by examining the spontaneous retardations which occur in heating and cooling it, and by examining the ductility of pieces of steel which have been cooled suddenly from different temperatures by quenching them in water or brine. IV.—A brief note on Osmond's theory. V.—A study of the critical points by examining the ductility of pieces of steel which have been cooled slowly from different temperatures at, above, and below them. VI.—A description of the furnace used, with notes on thermoelectric pyrometry. It remains to throw further light on the questions studied by ascertaining the condition of the carbon and the hardness proper, and by studying the microstructure and the fracture of the many pieces treated. I hope to present later the results of experiments in some of these directions. With few exceptions, the experiments have been performed in my private laboratory. I tender sincere thanks to my assistant, Mr. William Haskins, S.B., on whom most of the labor has fallen, for his zealous and intelligent co-operation; to the Sterling Steel Co. for their extra hard steel, Series 17; and to Mr. Joseph Hartshorne and the Pottstown Iron Co. for their soft basic steel. Series 8, 9,10, and 18 were supplied by Messrs. Spaulding, Jennings & Co., of the West Bergen Steel Works; to them also my thanks are due. The temperature of the pieces treated has been very carefully

Jan 1, 1894

By Walter Lee Brown

One of the characteristic steps in the march of modern scientific progress is the substitution of improved time-saving and labor-saving appliances for the antiquated and, in most cases, inconvenient forms of chemical and physical apparatus used by the earlier experimenters. This fact is strongly impressed upon us when we consider the question of the employment of illuminating-gas as a source of light, heat and power. Concerning its value as a light-producer, let the record of the past three-quarters of a century speak for itself. As a factor for power, we have evidence of its efficiency in the shape of the gas-engine. But its adaptability as a medium of heat, is the feature to which I wish to call attention, and in a special direction, viz., the assaying of ores. Gas assay-furnaces have been known and used for some years, but not to any very great extent, in this country at least. Therefore no apology on my part is required for the description I now give of a complete gas assaying-plant. The illustration accompanying this paper is a faithful representation of the group, as it was designed by, and arranged for myself, and appears in actual running order in my laboratory to-day. Its duty is to do roasting, crucible-fusion, scorification and cupellation. The furnace at the left is for roasting sulphurets or other ores for experimentation or actual work. It is what is known as a Fletcher No. 163, and consists of a fire-clay body strapped with sheet-iron bands, and a burner (No. 16, Fletcher). The opening at the top

Jan 1, 1885

William Kent, New York City: I regret that I have not had the time since the Cincinnati meeting to make as complete a study of Mr. Salom's paper as I wished. I regard it as one of the most important papers that have been presented on this subject, and worthy of complete study. I started out, on the limited time I had, on a system of study which I would recommend to any one else who has leisure to complete the investigation. I took the original report presented at the Cincinnati meeting, and selected from it' such tests as had the analyses reported along with the physical tests, giving the amounts of carbon, phosphorus, manganese, etc., taking only those in which all these elements are given.

Jan 1, 1885

By Joseph D. Weeks

Manganese has, until recently, been most highly esteemed as a good thing to keep out of steel. Its value in the process of mannfacture has been fully recognized, but after it has played its part in the crucible or the converter, then the less of it the better. It is true that the mission of this metal and its influence upon the character of steel has been a source of much controversy. Our own Holley, in one of his special reports on ferromanganese: I, states that ''it has been suspected by some, and believed by a few, while it is still denied by many, that manganese as an ingredient in steel has not only a body-giving and toughening influence, but a positive neutralizing influence upon any excess of hardening or cold-shortening substances, as phosphorus." In another paper on the same subject he states that " it should appear from such facts as we have that manganese toughens" the structural steels, "increases their soundness and prevents red-shortness." Notwithstanding these rather guarded assertions as to its value, the general belief, it will be found, is with Dr. Siemens, that manganese is " merely a cloak to hide impurities," and its presence in steel has been endured, not welcomed. But whatever may have been the difference in opinion as to the

Jan 1, 1885

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By John Gjers

Being on a visit to your great and prosperous country, and having been favored with an invitation to attend this meeting of your Institute, the author has been requested by your Secretary to give a short account of his invention of the " soaking-pit," which he has great pleasure in doing. The object of the soaking-pit is the rolling of steel ingots with their own initial heat, that is, to supply the missing link in that chain of metallurgical operations which Sir Henry Bessemer began in 1857, when he proved how it was possible to produce malleable iron or steel direct from the fluid cast-iron out of the blast-furnace, without any further direct use of fuel. The great Bessemer invention has revolutionized iron and steelmaking throughout the world; but it stopped short at producing the ingot, which, it was found, had afterwards to be heated in a furnace to enable it to be rolled or hammered; and it is only lately, twenty-five years after Mr. Bessemer's announcement, that the author of this paper has been able to show that furnacing can be dispensed with, and that it is practicable to roll a steel ingot into say a bloom, a rail, or a billet, with its own initial heat. It has no doubt suggested itself to many that there ought to be heat enough in the ingot just cast, for the purpose of rolling; and from time to time attempts have been made to utilize this heat; but such attempts always ending in failure, it became a settled opinion in the trade that it could not be done—an opinion which the author is aware that your late lamented countryman, Mr. Holley, than whom there was none more conversant with Bessemer steel-making, also entertained. But settled opinions sometimes prove to be great fallacies. As an instance, it is not many years since the opinion prevailed in the trade that steel ingots could not be rolled successfully, that is, so as to make good rails, unless they were first allowed to get quite cold, and afterwards heated. No greater boon was ever conferred on the

Jan 1, 1885

By C. A. Stetefeldt

FoR the convenience of those who do not care to enter into the details of this long essay, I begin with a summary of the most important results it presents. The extraction of silver by the lixiviation-process from ores which have been subjected to a chloridizing-roasting, is based upon the fact that silver chloride is easily soluble in solutions of sodium or calcium hyposulphite, and that silver is precipitated from such solutions by an alkaline sulphide, with regeneration of the hyposulphite salts. In case the ore contains lead a large portion of the latter is and dissolved, lead sulphate being soluble in hyposulphite solutions. If, at the same time, copper is present, the sulphides precipitated from the solution, contain silver, copper, and lead, a combination of metals not desirable for subsequent treatment. Mr. E. H. Russell, of Park City, Utah, is the inventor and the patentee in the United States and several foreign countries of a new lixiviation-process, based upon the chemical facts discussed in this paper. Mr. Russell has discovered that lead can be completely separated from a sodium hyposulphite solution, as lead carbonate, by sodium carbonate or purified soda-ash, without precipitating any copper or silver. After decanting the solution from the lead carbonate, silver and copper are obtained from it in the usual way. This method of separating lead prohibits the use of calcium poly-sulphide as a precipitant for the sulphides, because any calcium entering the regenerated lixiviationsolution would also be precipitated as a carbonate with the lead by soda-ash. Hence, a sodium sulphide must be employed. A full investigation has demonstrated that this is by no means detrimental. Sodium sulphide and hyposulphite are more advantageously used in the lixiviation-process than the corresponding calcium-salts. Another defect in the lixiviation-process consisted in the necessity of a very perfect chlorination of the silver in the ore, because silver in

Jan 1, 1885

By John Birkinbine

Among the notable deposits of iron-ore, the Iron Mountain at Durango, Mexico, is prominent. But, although it has been noticed in records of travel and official reports for three centuries, the statements made concerning it have been so largely alloyed with improbabilities that general credence has not been given to data relating to the Cerro & Mercado, that being the name by which this remarkable mountain of ore is known. Location. Geographically, the mountain is centrally located, being situated immediately at the City of Durango, which is distant in direct lines (as the crow flies) as follows: From the Rio Grande River at El Paso, Texas, in the north, 510 miles; from the same stream at Laredo, Texas, in the northeast, 410 miles; from Tampico, in the east, 475 miles; from the City of Mexico in the southeast, 520 miles; from Mazatlan in the west, 110 miles. At El Paso, the standard-gauge Mexican Central Railroad, and at Laredo, the narrow-gauge Mexican National Railroad, enter Mexico. Tampico is a prominent Mexican port on the Gulf of Mexico, and Mazatlan occupies a similar position on the Gulf of California. To reach Durango from Laredo or Tampico, spurs of the Sierra Madre Mountains must be crossed, and between Mazatlan

Jan 1, 1885

By J. B. Mackintosh

THE present note is intended as an addition to my previous communication on the volumetric determination of manganese, read at the Roanoke meeting," it having been suggested that the circumstances under which my experiments had been conducted, were essentially different from those met with in the analysis of irons. The method used in these experiments is the same in all its details as that described in the paper referred to. I have made seven experiments in all: two of these were in duplicate on half a gramme of a sample of spiegel dissolved in hydrochloric acid; one was on the same amount of spiegel with the addition of 25 C.C. of a standard solution of potassium permanganate; one was on the same amount of spiegel with the addition of 35 C.C. permanganate and much organic matter, viz., one drop of castor-oil, two or three drops of coal-tar benzol arid of gasolene (petroleum), about ten of alcohol, portions of starch and of sugar about the size of a small pea, and about half an inch of a common match cut into shavings. This organic matter was added to the manganese solution after the hydrochloric acid had been replaced by nitric, and the solution was heated until the wood-shavings had disappeared. The fifth experiment was made by dissolving half a gramme of spiegel alone in nitric acid; the sixth by dissolving half a gramme of spiegel in nitric acid with the addition of 25 C.C. potassium permanganate, some oxalic acid, half an inch of a match, one filter-paper 7 cm. in diameter, and two drops each of castor-oil and turpentine; and the seventh experiment by dissolving half a gramme of spiegel in hydrochloric acid and adding 35 C.C. permanganate, without however taking the precaution to evaporate off all the excess of hydrochloric acid. Under these circumstances, one would expect that if organic matter exercises any influence on the determination, it would be plainly evident in the results obtained. But the accompanying table of results

Jan 1, 1885

By Samuel B. Christy

At the last meeting of the Institute, several contributions were made to the subject of miners' aid funds. Such matters will always form important factors in the administration of large industrial enterprises. From the frequently remote and isolated position of mining properties, it is a subject that often forces itself upon the attention of the mining engineer. Local conditions are usually so variable that no single method can be found equally well adapted to all localities. At the same time, a study of different types is often suggestive and valuable, and it is with this in view that these notes are presented. The Miners' Fund of New Almaden is a remarkably successful example of what may be done for miners by a wise and at the same time firm management, by simply directing their own efforts and without incurring any great expense to the stockholders,—a practical consideration not without importance in most cases. The quicksilver mines of New Almaden are situated at a distance

Jan 1, 1885

By J. C. Bayles

Jan 1, 1885

By William Kent

I DESIRE to place on record in our Transactions a recent innovation in blast-furnace practice, namely, the introduction at the Lucy Furnaces, in Pittsburgh, of four water-tube steam-boilers, of the Babcock and Wilcox pattern, aggregating 832 horse-power, builder's rating, or 9,568 square feet of heating-surface, utilizing the waste gases of the furnaces as fuel. The boilers are set in two batteries, each of 416 horse-power, and each battery occupying a ground-space of 22 feet 7 inches by 20 feet 4 inches. The accompanying dram-

Jan 1, 1885

By Victor Maksaev, Marcos Zentilli

"Abstract - The Domeyko Cordillera, the westernmost uplifted crustal block of the composite High Andes of northern Chile (20°S to 28°S) hosts a narrow N-S trending belt of Late Eocene-Oligocene giant porphyry copper deposits, which include Collahuasi, Chuquicamata, El Abra, La Escondida, and El Salvador. These deposits are spatially and genetically associated with the closing igneous activity along this range, prior to a 30 km eastward jump of the magmatic front in response to tectonic plate interaction. The porphyry copper deposits are also spatially associated with a major intraarc strike-slip shear system, the Domeyko Fault System. Although the tectonic uplift of the 3000 m to 5000 m high range has generally been assumed to be mostly Miocene in age, field relationships suggest that the Domeyko Fault System and tectonic uplift were active as early as the Eocene, coinciding with porphyry copper emplacement between 41 Ma and 30 Ma. Apatite fission track (FT) thermochronology provides both age data and a time-temperature history for rocks since they cooled below a temperature of ca. 125°C (equivalent to a depth of 4 km to 5 km under normal geothermal gradients) on their way to the surface during exhumation, or after a heating event. Apatite FT data from the Paleozoic crystalline basement of the Domeyko Cordillera indicate that at least 4 km to 5 km of rocks were eroded during exhumation of this tectonic block between ca. 50 Ma to 30 Ma (Middle Eocene to Early Oligocene), a time that immediately precedes and overlaps with the emplacement of giant porphyry copper deposits. The FT data constrain the age and duration of a period of crustal thickening and extensive erosion known as the Incaic compression, an event recognized in the Andes of Chile and Peru. Assuming that cooling was due to denudation alone, modelling of the FT data allow estimation of denudation rates between 200 and 100 m/My during this period. In contrast, exposures of pre-porphyry Paleocene intrusives on the western edge of the Domeyko Cordillera reveal apatite FT ages that are concordant with biotite 40Ar-39Ar dates, indicating shallow emplacement, fast cooling and negligible exhumation. The apatite FT ages of the Chuquicamata and El Abra porphyry copper deposits are only marginally younger than their 40Ar-39Ar dates, implying fast cooling/exhumation of shallow mineralizing systems (ca. 2 km to 3 km). Their FT time-temperature history is compatible with extremely low rates of exhumation (ca. 50 m/My) since about 30 Ma (Early Oligocene). This limited extent of erosion, due to exceptional aridity, has greatly contributed to the preservation of rich supergene enriched blankets above some of the porphyry copper deposits.A model is proposed, which is consistent with field relationships, geochemical, and geochronological data. High relative velocities and intermediate-angle oblique convergence between the Nazca and South American plates in the Eocene-Early Oligocene led to intra-arc transpression partitioned into reverse faults of opposing vergence and a right-lateral shear system (the Domeyko Shear System) localized along the magmatic front. Crustal shortening and thickening led to uplift within the Domeyko Fault System and to erosion of at least 4 km to 5 km. Crustal thickening deepened the zone of magma generation, and magmas accumulated in the lower crust, allowing small volumes to rise rapidly to shallow levels along transtensional domains of the regional shear system. A similar model of crustal thickening and shortening before and during porphyry copper emplacement in zones of transtension may also apply to the Miocene-Pliocene giant porphyry copper province of central Chile."

Jan 1, 1999

By M Jara, R Nuñez

As the global interest in sustainable energy sources has increased, lithium has emerged as a vital resource, playing a crucial role in the transition towards a cleaner and more efficient economy, but with this comes important challenges, especially associated to health, safety, and environmental matters. So, it is imperative for the lithium industry to prioritise HSE measures to protect workers, environment and surrounding communities. Implementing robust safety protocols and technology helps ensure the sustainability of mining operations and contributes to the overall responsible development of the industry. In this work we present how the Chilean lithium mining industry becomes a safer and more compliant industry using digital transformation (Cochilco, 2018; Bradley et al, 2013; Cabello, 2022).

Apr 16, 2024

APPROXIMATELY 26 percent of the total ore production to date from the largest single deposit of copper-bearing material in the world was mined during the war years, 1942 to 1945, at Chile Exporation Company's great open-pit mine at Chuquicamata, Chile. About 18 percent of the total waste removed during the life of the mine was handled in the same period. The total of ore and waste represents approximately 24 percent of the total material that has been excavated from the pit. This is more than was removed in the first fourteen years of operation from 1914 through 1927. The pit at Chuquicamata is 17/8 miles long, 1/2 mile wide, and has a present vertical extent of 817 ft between the top of the highest bench and the lowest bench being worked. However, when

Jan 1, 1948

By Kyle Kittle, Kyle Knaeble, Albert Ruiz, Gregory Raines, Ryan Gewargis

The Chimney Hollow Reservoir Project (CHRP) is located southwest of Loveland, Colorado. CHRP is a component of the Windy Gap Firming Project, operated by the Municipal Subdistrict of the Northern Colorado Water Conservancy District. The inlet/outlet tunnel (IOT) for CHRP contains a reinforced concrete lined alve Chamber with PC membrane waterproong that was ecavated via seuential ecavation method to a diameter of feet. The IOT was ecavated using both drill and blast and road header with ground support consisting of steel sets, rock bolts, wire mesh and shotcrete. The IOT will withstand 300 feet of water head and rock ll surcharge load from the dam embankment constructed over the tunnel.

Jun 23, 2024

By Janine Lahr, Peter E. Halbach

The Manus Spreading Ridge is located within the EEZ of Papua New Guinea and lies in the Manus Basin ENE of the PNG Island and N of the Island New Britain. The divergent backarc spreading system is caused by the subduction of the Solomon plate in the South under the Bismarck plate in the North along the lineament of the New Britain trench. The rate of divergence is relatively high compared to other back arc spreading systems and amounts up to 12 cm/year [3]. Since submarine volcanism and associated hydrothermal circulation as important parts of the oceanic heat transfer system are also dependent on the rate of spreading, hydrothermal fluid venting and respective deposition of polymetallic sulfides can be expected there. In late 1985 first indications for hydrothermal activity were observed on a swell within the central rift valley of the Manus Spreading Centre during a photographic survey of the seafloor by an expedition of the Hawaii Institute of Geophysics with the American RV Moana Wave [1]. Detailed geological investigations including successful sampling were first carried out in June 1990 within the scope of the OLGA II research project (conducted by Prof. Tufar, Marburg) using the German RV Sonne equipped with a deep-sea television sledge and Tvcontrolled grab systems. Simultaneously a research cruise with the Russian RV Akademic Mstivlav Keldysh took place using the manned submersible Mir; the findings of the OLGA II cruise were immediately used for planning and organization of the Mir dives [3]. The massive sulphide samples which we used for our geochemical and mineralogical studies originate from the hydrothermal fields 1 and 2 and are from grab stations of the OLGA II expedition [4].

Sep 24, 2006

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018