Search Documents

Jan 1, 2009

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited's production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

"The theoretical basis of ideal smelting reduction using coal as reductant in a process employing closed loop forced-circulation of hot metal is outlined. In the proposed process, an extensive area of relatively slag-free hot metal is available as a heat sink for absorbing the large amount of heat produced by complete combustion of CO within the furnace. Any slag that is formed within the oxidizing arm of the furnace loop is quickly swept away as a thin floating layer by the bulk movement of hot metal which is induced positively by forced melt circulation and sustained by causing the hot metal and the thin slag layer to overflow into a lower level hearth in which coal is carbonised and dissolved directly into the circulating melt.The proposed process is shown to offer very substantial cost savings over all other direct smelting technology. This is mainly because of its inherently low capital cost and its high energy efficiency. Furthermore, the favourable economics are not reliant on fuel gas credits as all the process gas is combusted within the reactor itself.IntroductionMetallurgical processes in the year 2000 will be compromise solutions to the metallurgical problems that already exist today. It is common knowledge that the mineralogical complexity of certain polymetallic sulphides, for example, precludes high degrees of separation and recovery by conventional mineral beneficiation. steps are therefore being taken towards the development of a truly polymetallic smelting process which will produce simultaneously zinc lead and copper as, metals from complex ores without prior beneficiation(l). In the ferrous extraction industry, the shortcomings of the highly efficient modern blast' furnace are well known and world-wide there is considerable effort being directed towards coal-based ironmaking without the requirement of metallurgical coke as a process intermediate. The current status 0f2Joal-based ironmaking has recently been reviewed by Smith and Corbett. (2)"

Jan 1, 1988

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

By J. W. Parkinson

A coal-cleaning plant's environment can be hazardous to a computer system. The computer must be more reliable than the coal-cleaning plant mechanical processes if it is to help improve clean-coal quality and yield by performing data gathering and process control tasks. This paper discusses coal-cleaning plant environmental hazards and installation philosophies that can protect the computer. Specific reference is made to a computer system installed at the Electric Power Research Institute's Coal-Cleaning Test Facility.

Jan 1, 1983

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

Discussion of the papers of DAVID H. BROWNE, Louis V. BENDER, and R. E. H. POMEROY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January; 1915, pp. 49 to 60, 73 to 81, and No. 98, February, 1915, pp. 445 to 453, respectively. E. P. MATHEWSON, Anaconda, Mont.-After hearing about the success of D. H. Browne with his furnaces, we in Anaconda decided we might venture into the field of pulverized coal for reverberatory smelting. We sent a delegation of investigators to see Mr. Browne and his work, and they returned, filled with enthusiasm, and said they would recommend it strongly. We thereupon asked for an appropriation, and after some delay obtained the same and fitted up one furnace to use pulverized coal. We copied Mr. Browne's practice and his selection of machinery for drying and pulverizing coal; and we also copied the burner he used, which was a standard article on the market. We got an expert coal-dust machinery man to design our plant, and were very glad we did so as we avoided some of the unpleasantness that had been experienced at other plants through fires and minor explosions.

Jan 5, 1915

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936