Search Documents

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By John W. Tieman

The increasing magnitude of our nation's pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country's 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation's 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By J. H. de. Visser

The transfer of molten metal in smelting or refining operations is typically performed in open trough-type launders that are constructed of either water-cooled copper troughs or refractory lined steel jackets. This transfer can be either continuous or batch. Batch operations transfer metal through an open launder. The uncovered launder has many operational and environmental drawbacks. In order to improve workplace hygiene, designs have evolved toward ventilated launder covers that .are connected to secondary exhaust systems that use negative pressure under the cover removing fume and hot gases to secondary fume control devices. In smelting operations, a variety of covers have been employed which insulate the launder and contain the fumes and also provide additional heat along the length of the launder through a series of premix or inspiration-type burners that add combustion products to the normal fume load in the launder. Cover designs have proven to be inadequate in that hinged unventilated covers hinder convenient access while heated ventilated covers are costly to maintain. Covers that employ refractory bricks and overhead enclosure-type exhaust hoods have been somewhat successful, but restrict operator movement and require large volumes of exhaust air. An example is given of a cover and off-gas system for launders that is designed to provide superior insulation and heating capabilities, as well: as better control of the fume gases-and ease of maintenance. The cover system must maintain the balance between maintaining launder heat and fume removal. The construction of the covers must be able to withstand high internal temperatures and maintain its structural properties.

Jan 1, 1999

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By William Gregg

Recent environmental and workplace safety legislation has Imposed more stringent limits on the amount and type of particulate emitted Into the air. In the past, the mass of particles contained In a volume of air was the governing criteria. Now the size and precise chemical nature of the particulate must be known and controlled In addition to it's ?mass. Processors of metallic materials have to implement stricter control practices and more efficient control equipment to meet the new regulations. Pulse-Jet dust collector systems are being used to control particulate emissions from various process gas streams. Pulse-jets :are also being used for maintaining a healthy environment In the workplace. this paper will discuss the impact of these regulations, the control techniques used to comply with such regulations, and the equipment needed for compliance.

Jan 1, 1992

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

Problems caused by water discharge from surface mine ventilation shafts can be significant and are usually unforseen. The discharged water is often hyper-saline or acidic and can cause environmental degradation over a wide radius. It can also lead to recurring power pole fires and primary fan breakdowns. A range of solutions to the water discharge problem has been implemented in many Australian mines. In most cases the solutions have been ad hoc, with the overall cost and effectiveness varying tremendously. This paper reviews and contrasts the practicality and effectiveness of the various available remedial options.

Jan 1, 2002

The hydrological cycle in nature, with particular reference to Australia . 2. The definition of water pollution drawing on the experience of several major countries. 3. A description of the pollutants in water, and why they are pollutants. 4. The classification of waters as defined by major overseas countries. 5. The criteria and standards developed by major overseas countries for the classification of waters. 6. A brief- summary of the legislation adopted by overseas countries for the control of water pollution, and of the organisation and administration of controls. 7. A study of Australian legislation and administration of controls of water pollution. 8. General observations and conclusions.

Jan 1, 1971

By Luis G. Bergh

Today, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design. In this work, a model of a rougher flotation circuit, based on operating variables and parameters fitted from industrial data, obtained in some previous work, is used to develop a set of logic rules in order to aid operating decisions. The simulator was first used to sensitize the effect of changing the froth depth profile on target variables, and then to find out the best profile to reject common disturbances coming into the plant. The flotation circuit simulator was redesigned to incorporate an expert system following the proposed control algorithm. Several tests were performed to evaluate the control responses to different correlated series of input variables, such as feed grade, tonnage, particle size distribution, and solid percentage. Control alternatives are discussed based on the circuit simulator. Keywords: modeling, industrial data, flotation control, mineral processing.

Sep 1, 2012

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By R West

The Olympic Dam smelter facility processes copper concentrate feed using direct-to-blister smelting technology to support the current site production rate of 225 000 t/a copper. The metallurgical control of the Olympic Dam smelter is largely managed from a single central control room. Control room operation and management is therefore a key function in ensuring safe and reliable operation of the smelter, including identifying and initiating control of abnormal events. As part of a consolidated smelter reliability improvement program, a team consisting of process and control system engineers was formed. The teamÆs charter was to address and resolve the alarm flooding issues being faced by the control room technicians and the lack of an up-to-date base of supporting functional documentation. The project was successfully resourced with WorleyParsons metallurgists, Citect PLC technicians and the on-site technical team. Implementation was conducted over a 12 month period with the goal of achieving best practice alarm levels. The goal was achieved through a systematic process of alarm design review that analysed every configured alarm versus best practice design standards. Innovative concepts such as group-based alarms, first-up interlock displays, graphic only alarming, alarm help and alarm shelving were developed and implemented in conjunction with improved alarm masking. Total configured alarms were reduced from 20 000 to 5000 while the alarm rates were reduced from in excess of 200 alarms per hour per controlling technician to best practice levels of less than 12 alarms per hour per controlling technician. Completion of this program has provided a firm foundation for implementing further control optimisation and was a key activity in supporting sustained smelter reliability levels.

Jan 1, 2005

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By Alexandre de Freitas Gomes de Mendonça

O pick-up de nitrogênio no aço deve ser evitado nos processos de fabricação em uma Aciaria de alto desempenho. Entretanto, o pick-up de nitrogênio pode ocorrer em inúmeros pontos na Aciaria, principalmente quando o aço líquido é exposto ao ar atmosférico. Alguns locais de controle têm grande relevância no resultado do pickup, tais como: durante o vazamento do aço do convertedor para a panela, no refino secundário durante a agitação excessiva do aço e no lingotamento contínuo devido a aspiração de ar atmosférico nas conexões. Neste trabalho, o foco do controle da incorporação de nitrogênio é no lingotamento contínuo e, para efeito de estudo, tomou-se como referência um pick-up de nitrogênio de até 5 ppm. Os dados históricos mostram que menos de 64,6% das corridas encontravam-se com pick-up de nitrogênio abaixo de 5 ppm. Assim, visando reduzir esse pick-up foi proposto um ajuste no ângulo da sede da válvula longa, melhoria do projeto do gasket e capacitação da equipe de operação. Após a efetivação dessas ações de controle esse número passou para 97,7% das corridas lingotadas.

Jul 30, 2018

By Otaviano Donizeti Valadão de Freitas

Ruídos elétricos afetam os circuitos lógicos e conseqüentemente podem comprometer a confiabilidade nos controles de processos, e para minimizar as influências desses ruídos, algumas medidas básicas foram tomadas, com instalações adequadas de todo o sistema, como padronização do aterramento, encaminhamento de cabos, etc. Depois que as medidas foram implementadas, o resultado foi um sistema mais confiável. Se apenas um fio for encaminhado de forma incorreta ou se o aterramento estiver inadequado, pode ser suficiente para causar problemas. A experiência mostra que é muito difícil que todas as medidas sejam aplicadas integralmente, mas se não forem tomadas pelo menos as medidas básicas, o sistema ficará suscetível.

Sep 25, 2017

By Ivor Jenkins

PROCESSES employing controlled atmospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been associated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and difficult problems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases Controlled atmospheres such as dissociated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties: especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,1 but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1947

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011