Search Documents

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

By Sridhar Seetharuman

Sulfur and oxygen dissolved in nickel and cupronickel melts can be removed as gaseous oxides of sulfur by a vacuum treatment. Presented in this paper is a new matched thermochemical diagram that permits direct evaluation of the equilibrium partial pressure of SO, as a function of temperature over an alloy of specified composition. The matched thermochemical diagram consists of a central plot which shows the integral Gibbs' energy of mixing for the binary system S-O2, at different temperatures. The central plot is flanked on either side by terminal plots of the chemical potentials of oxygen and sulfur, as functions of temperature, for different alloy compositions. By projecting the chemical potentials of oxygen and sulfur from the terminal plots on to the central diagram, the equilibrium pressure of SO2,can be directly read on the nomograms on the central plot at different temperatures. The matched thermochemical diaerams are - useful in assuring the efficiency of vacuum refining.

Jan 1, 1993

By F. Soumis

We propose an advanced truck dispatching system which uses mathematical optimization approaches including integer programming, non-linear networks and the assignment problem. The system produces better operation control than existing algorithms. Furthermore, it provides planning tools for choosing equipment and finding an equilibrium between the quality and quantity of production.

Jan 1, 1986

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By C. H. Herty Jr, C. H.

FEW subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebui interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon; 1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods3 give only the more insoluble oxides SiO2 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1957

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By C. C. Hawes

SILICA is the main impurity in iron ore. It is intimately associated with the iron oxide, sometimes free but more often in the combined state, as a mineral silicate. Its separation and purification sometimes present difficult problems to the analyst. In the absence of any definite knowledge to the contrary, orthosilicic acid. H4SiO4, is supposed to be the only silicic acid made, all other forms, such as metasilicic acid, H2SiO3, representing different degrees of its dehydration. These acids are exceedingly weak but form the most stable compounds found in nature. They are known as the silicate minerals and are formed by the combination of the different metallic oxides

Jan 1, 1936

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By Frederick C. Hull

THE grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. USUAL METHODS of EVALUATING GRAIN SIZE A frequently used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.-The Metals Handbook1 has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.-Idealized grain-boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E19-39T. Standard Micrographs.- The Metals Handbook and ASTM Tentative Standard EI9-39T contain micrographs of hypoeutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diam¬eter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying grain size in ASTM Tentative Standard Es-39T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1947

By Dominique François-Bongarçon

A new method for open-pit design has been devised by G. MATHERON and the writers: it replaces the search for an optimum contour by the determination of a parametrizing function. The isovalue curves of this function give the optimum pit design corresponding to varying economic parameters; The method is described and indications are given about the corresponding program. Simulated data have been processed by the program and by a standard program using LERCES-GROSSMAN graphical method: the comparative results are described.

Jan 1, 1977

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By B W. Atkinson

Full-stream mechanised sampling apparatus, that collect a full cross-sectional increment from the complete screen discharge, will always be the preferred option for sampling screen overflows. However, the reality is that provisions for automated sampling are rarely, if ever, provided at the discharges of individual screens within beneficiation plants.Sampling from the discharge of high capacity vibrating screens, especially multi-slope screens, is subject to sampling bias, due to the stratification of the ore that occurs on the vibrating screen deck. The stratification in the vibrating bed translates to a stratified falling stream at the discharge end of the screen, typically with smaller particles at the back of the falling stream and large particles at the front of the falling stream (Figure 1).The chemical and physical characteristics of heterogeneous ore (mineral or coal) particles vary significantly with particle size. If samples do not correctly reflect the source material size distribution, they will be biased and the resulting analytical/assay data will not reflect the actual physical nor chemical characteristics of the source material.Prior published data for coal preparation research (Australian Coal Association Research Program) has demonstrated that a bias appears to exist for samples collected from high capacity multi-slope screens.A new form of sampling scoop has been developed with the aim of overcoming this issue.Bias was evaluated at a coal preparation plant by comparing the desliming screen overflow size distribution to that for æreferenceÆ coal preparation plant feed samples collected using the recognised stopped-belt technique. The study procured 20 sets of comparison samples in order to ensure statistical relevance.Two forms of sampling device were employed for the multislope screen discharge.A conventional square aperture scoop was demonstrated to exhibit a significant coarse bias, in that the resulting samples exhibited a significantly coarser size distribution compared to the reference samples. In other words it was evident that the conventional scoop æfavouredÆ material from the front of the falling stream.A new æcollapsibleÆ sample scoop was evaluated in parallel, and its samples were found to exhibit no relevant bias.CITATION:Atkinson, B W and Swanson, A R, 2012. A new method for sampling from high capacity screens, in Proceedings Sampling 2012 , pp 89-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By A. L. Bleloch, A. M. Starfield

This paper is concerned with heat flow in the plane of a typical cross-section of a deep underground airway. A new algorithm, called the quasi-steady method, is presented for the calculation of rock temperatures in that plane. The algorithm is used in the computation of heat and moisture transfer rates from the rock to the ventilating air for an airway that is wet on part of its circumference and dry elsewhere. The speed and accuracy of the new method are demonstrated on a microcomputer, and it is argued that this method offers a considerably more versatile and physically meaningful alternative to previous methods for the prediction of increases in air temperature along mine airways. The algorithm is also used to explore the concept of a uniformly wet airway that is equivalent to a partly wet airway in terms of its effect on the ventilating air. The concept is shown to be reasonable, but more complex than one might have anticipated. Finally, several useful extensions and applications of the new method are suggested.

Jan 1, 1983

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004