Search Documents

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

By W L. Daniels, C Stilson, C Zimmerman

Mineral sands mining for ilmenite, rutile and zircon has disturbed over 1000 ha of prime farmland in Virginia (USA) since 1997 and additional areas are likely to be disturbed in Virginia and North Carolina (USA) over the next 15 years. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc. and restoration protocols have continued to evolve in response to a variety of economic, technical and social issues. Early on, the return of these lands to agricultural row-crop production was complicated by vertical stratification of tails + slimes and lateral variability in soil physical conditions in the reclaimed pits and by limited topsoil return. Virginia Tech and Iluka have worked cooperatively with all stakeholders for over 20 years to review the pre-existing research base, conduct new and innovative site-specific research and thereby provide reasonable expectations of post-mining soil productivity levels. In 2004, Virginia Tech, Iluka Resources and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45 ha research demonstration farm where the long-term effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Row crop yields between 2005 and 2010 were significantly above county average yields (regulatory target level) and approximately 75 - 80 per cent of undisturbed adjacent prime farmlands. The state regulatory authority has recently relaxed its position on the necessity of topsoil return versus use of topsoil substitutes based on appropriate on-site research results and the ability of the reclaimed soils to meet comparative local county crop yield targets. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry. CITATION:Daniels, W L, Stilson, C and Zimmerman, C, 2012. Development of effective rehabilitation protocols for mineral sands mining in Virginia, USA, in Proceedings Life-of-Mine 2012 , pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

Various influences determine how an Environmental Management System (EMS) for a mining or petroleum project is developed and administered. These influences include the environmental and resource legislation applying to the project, the culture of the organisation, the environmental sensitivity of the area, and the administrative policies of the regulatory agencies involved. While financial penalties and even imprisonment may be imposed for non-compliance with environmental legislation, there are other compelling reasons for the establishment of an effective EMS. If a company wishes to be considered by Governments for the grant of exploration or mining rights, it is important that it can demonstrate environmentally responsible operations at existing facilities. The development of an effective EMS requires commitment from the Board of the company and the issue of an Environmental Policy to empower all levels of the staff and workforce to achieve environmentally responsible operations. This must be supported by the provision of appropriate human and financial resources, and environmental training of staff at all levels from the Board to the mine site, workshop and office. A regular environmental auditing programme is essential to ensure that the EMS is in place and is effective in achieving compliance with regulatory requirements, corporate policies and protection of the environment. An EMS can be developed on the basis of existing management systems, quality management systems, existing and emerging environmental management standards (such as BS7750 and ISOI4000), or sophisticated computerised systems which may incorporate international experience, standards, and codes of practice.

Jan 1, 1995

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Meike Klischies

Technological advances and the shift towards green energies in the last decades have led to a substantial increase in the demand for metal resources. With rising political tension, and quasi-monopolistic production of some key metals, a secured supply chain cannot be guaranteed [1]. Therefore, the focus of the international research community and mining companies has expanded to the seafloor, looking for additional resources. The seafloor may have the potential to contribute significantly to a secure metal supply in the future. However, we have only investigated a fraction of our oceans in sufficient detail to assess the global resource potential. A detailed exploration of the vast seafloor is currently economically not feasible, due to its extremely time-consuming and costly nature. Seafloor massive sulfides generally form along the active plate boundaries and at active volcanoes in arc settings. However, the resources are not evenly distributed on the seafloor. Large deposits tend to be more common along slow-spreading and ultra-slow- spreading ridges that make up the majority of the global mid-ocean ridge system [2]. Therefore, it is important to establish geological models and exploration criteria in order to narrow down the permissive areas, which are likely to accommodate economically interesting deposits. Based on a detailed study of the TAG hydrothermal field in the central Atlantic Ocean, hosting a large active mound as well as several inactive mounds, we develop exploration methods and criteria to define areas of potential massive sulfide occurrences along slow-spreading sections.

Jan 1, 2018

By Claude E. Wykes

Deep Well turbine pumps receive constantly increasing application to the problem of mining water and other fluids from great depths. Many installations of medium settings are presently operating successfully and it is felt that mach greater depths are immediately within reach. Settings and lifts in excess of 2000 feet: are not at all out of reason with present knowledge experience, and materiels; however, conditions of individual applications will govern in each case and dictate methods and possibilities to the designer. Design and operating problems of deep set -turbine pumps ire discussed together with a description of various types of equipment falling within this category. Although the deep well turbine pump has been produced In the vertical turbine pump industry for many years, the connotation of the word "deep" still remains questionable. Among the manufacturers of this type of machinery, answers to the question implying the practical limitation of setting for a deep well pump will vary to an extreme. Most pump designers are in accord that this type of equipment has not yet been exploited to its fullest degree; however, the subject is admittedly fraught with unsolved problems and un¬tried solutions so that such a discussion must necessarily derive from personal opinion and, belief., even though based on substantial experience and background. For this reason, it will be stipulated that the present writing will deal with what may be termed euphemistically ?a highly controversial subject.? During the nineteenth century, a paper was published under proper authority proving beyond question that the human body could not withstand speeds exceeding 20 miles per hour. As a limitation, this looks ' pretty ridiculous to us today. At the beginning of the twentieth century, there was not a single machine in operation that could be described as mullti-stage deep well centrifugal pump. As a matter of fact, very few centrifugal pumps of any type wire operating against heads in excess of 50 feet, since such applications were considered impractical. In the

Jan 1, 1960

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By R. Singh

The present paper deals with the development of flotation based process for enrichment of a lead-zinc sulphide ore from Ganesh-Himal region of Nepal. Detailed characterisation and flotation studies were carried out under varying process conditions. The sample assayed 2.47% Pb with 13.6% Zn. The ore was predominantly made up of spahlerite and pyrite in association with subordinate amounts of galena, minor amounts of pyrrhotite and chalcopyrite. Dolomite was the main gangue. The modal analysis showed the probability of fair liberation of sulphides from gangues around 210 microns but the locking of galena with sphalerite and other sulphides continued to finer sizes. Under the optimum process conditions the rougher lead and zinc recoveries were 96.3% and 90% respectively. Multistage cleanings of rougher products proved helpful in improving the concentrate grade, meeting the required specification. Based on the studies undertake a process flow-sheet for the concentration of the ore to individual lead and zinc concentrates was developed.

Jan 1, 2014

By Ö. Y. Gulsoy, L. Ergün, I. B. Celik

"In this study, the studies to develop a flowsheet for a low grade chromite ore are presented. The existing concentrator had to be suspended due to the decreasing metal prices. The study commenced with mineralogy and liberation profile of the chromite. The valuable mineral is chromite and the major gangue mineral is forsterite together with small amount of brucite and calcite. Heavy liquid tests were performed on different size fractions without any acceptable success. The concentration tests were performed using teetered bed separator (TBS) +shaking table, spiral concentrator+TBS+shaking table for different grind size. Based on the test results, 100% finer than 0.4mm was found to be optimum for grind size. Comparison of alternative circuits showed that the performance of both alternatives would be similar. A flowsheet was designed and operated for as 25 tph trial circuit in the existing plant. The results showed that the performance of the plant predicted was very close to the actual plant data. The paper describes the methodology used, presents the experimental data and actual performance figures.INTRODUCTION Turkey is one of the largest chromite producers in the world. Since 1850, chromite mining found industrial applications and geographically spread along six different regions in Turkey. Although the reserves in these locations are not as rich as the big producers, they are regarded as very valuable due to Cr/Fe ratio in terms of chromite utilization standards (1, 2). In this period, significant portion of high grade (=35% Cr2O3), directly marketable ore deposits have already been produced. According to General Directorate of Mineral Research and Exploration (Turkey) data; 83% of the known chromite deposits of Turkey which makes 242 341 000 tons in total, is consisting from the deposits those have a Cr2O3 grade lower than 10%. Only 5% of the known deposits (13 087 000 tons) has a grade of directly saleable (2, 3). Gravity concentration methods are well-known processes for chromite beneficiation and there are plenty of plants in the world and Turkey using these methods. As different equipment combinations can be used for the same enrichment method, different methods can also be used in combination for plant designs (4). Beneficiation of low grade and problematic chromite ores may lead to use these method and equipment combinations (5, 6). Ore liberation, the grades of Al2O3, SiO2, FeO and Cr2O3 in the obtained concentrate, Cr/Fe ratio, some physical and chemical properties between gangue and minerals (i.e. specific gravity, magnetic property, color, etc.) designate the selection and combination of these methods and equipment (7)."

Jan 1, 2017

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919