Search Documents

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

By E S. Bernard

Steel fibre reinforced shotcrete (SFRS) is increasingly being used as ground support in both civil and mining applications. In recent years, methods of assessing the performance of SFRS have been developed. These include the beam test such as that prescribed by ASTM C-1018 and the panel test prescribed in the EFNARC European Shotcreting Standard. The panel test has gained popularity in recent times due to the two-way action modelled in the test. However, some difficulties have been noticed. Shear failures sometimes occur and there appears to be a rather high degree of variability in the panel test results. A new method of testing panels has been proposed. A circular panel supported on three symmetrically arranged points has been assessed at the University of Western Sydney. This paper describes the new test which may be the basis of a new specification for the testing of toughness of SFRS and summarises research work which has been carried out to-date.

Jan 1, 1999

By J. Bacho

The modern drilling fluids industry is a dynamic, evolutionary environment. It is continuously striving to satisfy and anticipate the ever-changing needs of the oil and gas industry. The predominant driving forces in the industry over the past decade have changed dramatically. Health and environmental issues, coupled with economic and performance requirements, demand innovation and change from the drilling fluids industry. Emerging drilling fluid technologies will demand environmental considerations from mined components with additional emphasis on cost and performance criteria. Drilling fluids providers continue to search for and identify environmentally sensitive components which meet or exceed the performance of their more toxic predecessors. These changes have and will impact the components of drilling fluids that are mined.

Jan 1, 1994

The original and most basic relationship between mining company and explosive supplier was a simple one of consumer and product supplier. The divide between the two was quite clear-cut with neither taking much interest in the activities of the other. The explosive supplier had little understanding or share in the outcome, efficient rock breakage and therefore impact on mining and milling. Likewise, the mining company did not encourage the improvement or development of products. The transactions were limited to product and funds. This environment does not encourage any form of knowledge sharing, trust or optimisation of the mining process.Conversely, there are now a variety of relationships to the point that the mining company may simply be an asset manager whereby all æoperationalÆ aspects are contracted out. For the drill and blast aspect this takes the form of a æRock-On-GroundÆ contract whereby the explosives company takes on design, drill, load and fire responsibilities and is paid a rate per volume of broken rock. This removes the majority of risk to the mining company derived from having to produce broken rock and guarantees the cost of a portion of the overall unit cost of mining. The onus is now on the explosives supplier to break rock to a specification as efficiently as possible.There exist a number of variations between the æbasic supplyÆ and æRock-On-GroundÆ. These contracts may also include value sharing to encourage the explosive supplier to optimise the mining operation to maximise profit.This paper looks at some of the drivers for the change in explosive supplierûconsumer relationships and examines the æprosÆ and æconsÆ of a few of the options.

Jan 1, 2004

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

By B. J. Elliot

The Outokumpu Oy flash smelting furnace was designed for a capacity of 69,5 mtph of concentrate. The history of developments on the flash furnace, from the original operating capacity of 55 mtph to a proven capacity of 115 mtph of concentrate, is summarised. The new feature of operation at BCL Limited is ?the use of screened lump coal reduction in the settler region of the furnace. This paper considers the effects of settler bath reduction on the furnace smelting capacity, the condition of the furnace ?lining and bath, and ,the slag losses generated from the flash furnace and ultimately to discard. By using the settler bath reduction technique the capacity of the furnace for smelting new concentrate has been increased by 15% and hearth accretion has been eliminated by direct reduction with coal, which has also allowed the generation of a substantial protective lining on the furnace walls and roofs. As a result of improved slag losses from lump coal charging the metal recoveries on the flash furnace have increased from 70% to 87% for nickel, 68% to 82% for copper, and 28% to 45% for cobalt.

Jan 1, 1983

By T. Gerritsen, A. Matyas, F. Stober, I. Candy

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed. The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation.

Jan 1, 2004

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as 'spin to stall.' The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to 'spin' and 'wait' times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By Stober, Frank Allan

The paper describes the development of components in an lntegrated Furnace Control system for shielded-arc smelting focusing on operation and crucible integrity enhancement. The paper reviews the mechanisms of power, feed and energy input and losses into the shielded-arc smelting process and describes the furnace control system module development and integration to tailor the process. The ultimate success of a furnace control system application is transfer of knowledge, training, and operational support during furnace start-up and ramp-up phases and a model for how this has been achieved is discussed. The control modules of a shielded-arc laterite smelting furnace are described in detail including measured results and screen captures from application in a laterite smelting furnace. This paper focuses on developments in Integrated Furnace Controls tailored to shielded-arc laterite smelting but development of common furnace control modules for improved crucible and tapping operation integrity applied to other furnace processes, including immersed-arc smelting, is also covered. Keywords: IFC, Power, Feed, Supervisory, Control

Jan 1, 2004

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

By E. M. W. Skinner

Various models of near-surface kimberlite pipe emplacement have been proposed over the years. These include a top-down, phreatomagmatic model, a bottom-up, embryonic pipe model and three top-down explosive dyke models. AU of these models consider kimberlites as essentially the same rock type. However, different kimberlites have different pipe shapes and contain different rock types with very specific mineral assemblages and textures and therefore are likely to have been emplaced by different processes. Some authors have considered local geological differences as the principal reason for the contrasting geology but others argue that, while geological differences might contribute locally the petrographic peculiarities of particular kimberlites may be due mainly to inherent compositional differences specifically in the ratios of juvenile CO2 and H2O.

Jan 1, 2010

By Merete Tangstad, Ragnar Tronstad

Ferromanganese production in electrical furnaces is quite an old process. However, as the furnaces are getting bigger, the requirements of cost, yield, product quality, emissions and security are raised. With the increased expectations, the fundamental knowledge must follow. Within the last 25 years there has been a great effort both in the industry as well as the academic environment to push the limits of this process. This article will show some examples of improvements within fundamental data, reaction mechanisms and emissions over this time period.

Jan 1, 2014

By G. B. SOUTHWARD

MECHANIZATION is being developed to some extent in every coal field in the United States and it is rather difficult to say which State or section of the country has made the greatest advancement. Statistics now being compiled for 1928 will show the tonnage mined, the amount of equipment used in each of the coal-producing States, and the comparative tonnages and percentages of total tonnage mined in each of these States, and will reveal which field is making the greatest advancement as far as quantity of production is concerned. However, while the tonnage figures are of great importance there-are other phases of coal-mine mechanization, such as the types of equipment, the mining methods and coal bed conditions, which are of equal interest. The change from hand-mining practices in all of the various operations from the face to the railroad cars is, perhaps, more indicative than any other one thing of the real progress being made.

Jan 1, 1929

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona's mined land reclamation legislation would recognize Arizona's leading role in hard rock mining and emphasize the mining industry's economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

By Wilhelm Wendt

About five years ago we showed that it is possible to use the spectral in- formation in the light emitted by the off-gas flame of a PS converter for on-line production control. Very recently measurements have been performed using improved optical equipment and data evaluation software, resulting in both improved accuracy and the establishment of new optical process parameters. Using the optical signals the slag heats could be stopped at a predetermined Cu content of the white metal with an accuracy of +0.2% Cu m the range 74-78% Cu. A good correlation was found between the slag composition and optical data, providing a possibility for on-line monitoring of the SiO2 content of the slag. The measurements indicate the possibility of predicting the optimum end-point of the copper-making stage and having real time information on the impurity removal. Factors influencing the optical parameters, such as blowrate, Pb content, temperature etc. will be discussed.

Jan 1, 1993

By Alan English

INTRODUCTION During the Bicentennial Year in the United States of America, recognition should be given to the fact that 20 years ago the first large-scale commercial pelletizing plant was started and attained rated capacity. This was the beginning of a new industry. Twenty years ago the total production of pellets was principally from pilot plant facilities and totaled in the thousands of tons per year. At the present time the world production is slightly in excess of 280 million tons per year. This truly is a tremendous growth for any industry. Such a production growth obviously is accompanied by a similar growth pattern in the development of process, equipment, and facilities. During the growth and development period, different materials became more adaptable for processing. For example, initially the pelletizing of iron ores revolved around the magnetite concentrates where the heat of reaction constituted a very important part of the process fuel. During this growth period, specular hematite, earthy hematite, mixtures of hematite and magnetite, and even non-ferrous type materials were pelletized, a function previously thought not practical. The demand for the use of pellets has also broadened their concepts. At first they were made to replace the high-grade iron ores used in blast furnaces. Nowadays, not only have they replaced iron units, but they have had a major influence on the design of larger blast furnaces and have contributed to production rates in excess of 10 000 tons per day from a single furnace. They have also been used in the manufacture of steel, principally for coolants in the BOF practice. More recently, with the improved beneficiation techniques that have been developed over the same period of time, pellets have been used for the direct reduction process and can be used directly

Jan 1, 1977