Search Documents

By Peter Johnson, David Barber, Lachlan Henderson

"The traditional approach to rail tunnel fire safety design is to follow NFPA 130, which assumes a major tunnel fire could occur and requires bi-directional emergency ventilation. There is no regard to the impact of ventilation on fire growth and smoke production. In Europe and other parts of the world, the need for tunnel ventilation systems to provide smoke management in the event of fire is being questioned. The European Commission’s Safety in Railway Tunnels TSI is based on a philosophy that improved running capability (preventing fires and other events stopping the train in the tunnel) and elevated fire performance of materials means the chances of a major fire in a tunnel is highly unlikely, with only small fires expected, and no tunnel ventilation required. This approach is reinforced by the International Tunneling Association which has recently published an Engineering Methodology for Performance Based Fire Safety Design on Underground Rail Systems, which includes a methodology that does not require assessment of tenability in tunnels, but requires a scenario based risk assessment to be undertaken to determine overall fire safety measures. Recent research by the University of Edinburgh has shown that forced airflow from a mechanical ventilation system may promote fire growth and increase smoke volumes much more than with natural ventilation. Whilst the concept of no mechanical ventilation (i.e. natural ventilation) is a new concept for some, for many rail tunnels it is worthy of serious further consideration. RAIL TUNNEL SMOKE MANAGEMENT AND STANDARDS Smoke management using mechanical bi-directional ventilation systems has been a central part of the fire safety design solution under NFPA 130 for rail tunnels since 1982. The current version of the standard, NFPA 130: 2014, states that mechanical ventilation should be fitted to rail tunnels of length greater than 305 meters and an engineering analysis should be undertaken for tunnels of length 61 to 305 meters to determine whether mechanical ventilation should be fitted. However, this approach is not necessarily reflected elsewhere in the world. In Europe in particular, mechanical ventilation systems for smoke control within rail tunnels have taken a much less central role within the standards framework."

Jan 1, 2016

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

By Nar S. Dalal, Xianglin Shi, Val Vallyathan

"INTRODOCTIONIn an earlier communication 1 from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates of free radicals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubini et al.2 have also reported the detection by electron spin resonance (ESR) of the formation of SiO. and Si-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum ( -10-10 torr>3 and subsequent exposure to air,3 and to other gases,4 these radicals were identified2 as being formed by the homolytic cleavage of the Si-0-Si bonds and the reactions of the Si• and SiO- radical with atmosphere. Fubini et al.2 also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anca5 bad reported that lipid ·peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radica1 studies on a given quartz dust sample have been reported, except for some earlier work from our laboratory.1·6·7 We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radica1 measurements on a freshly made quartz dust. The dust's free radica1 content was measured using ESR spectroscopy while its cytotoxicity potential was estimated via hemolysis. Hemolysis was employed as the toxicity test because it is a widely used method for estimating the potential of a dust for disrupting the cell membrane. 8 The fibrotic potential was followed by measuring the dust-induced lipid peroxidation, using linoleic acid as a model lipid. As discussed below, the results obtained suggest new clues to the mechanism of the quartzrelated cytotoxicity and fibrogenicity. MATERIALS AND METHODSReagentsCrystalline quartz particles with a size range of 0.2-2.5 mm were obtained from the Generic Respirable Dust Technology Center, Pennsylvania State University, University Park, Pennsylvania. These particles were crushed in air to obtain quartz dust samples with particle sizes smaller than 20 microns. We chose to work with a dust with mixed particle sizes, rather than a specific range, as an effort to simulate the mining atmosphere. An agate mortar-pestle arrangement was used for the crushing and grinding because of the close similarity of the structure of agate to that of quartz. Diethylenetriaminepentaacetic acid (DETAPAC) were purchased from Sigma. All other chemica1s were purchased from Fisher or Aldrich.Hemolysls ExperimentsHemolytic activity of silica was measured, following an established procedure,9 as the amount of hemoglobin released from a 2 % suspension of sheep erythrocytes after incubation with 10 mg of silica dust for one hour at 37 °C. The hemoglobin release was estimated via the absorbance at 540 nm using a Gioford spectrophotometer. The procedure was calibrated by substituting the silica dust by a phosphate buffer solution as a negative control (background) and O.S % Triton-X-100 as a positive control (100% hemolysis). The percentage of hemolysis was calculated as follows:"

Jan 1, 1990

By A Datar, D Mulligan

The extractive phase of broad-scale mining can have major impacts on landscapes and associated ecosystems. Post-mining ecological rehabilitation typically starts with reconstructing topography. A fairly common industry practice has been to use landform elements such as plateaus, terraces, and gentle slopes for stabilisation purposes. However, this approach can lead to the generation of fairly uniform landforms that do not necessarily reflect natural ecosystems. Previous research in undisturbed and agricultural landscapes shows that ecological attributes and diversity in microclimates is positively correlated with landform heterogeneity. An objective of this study was to investigate if those findings are still valid in post-mining rehabilitating landscapes on North Stradbroke Island, Queensland, Australia. We investigated the relationship between landform heterogeneity and status of ecological recovery. The landform heterogeneity is measured through variance in three landform characteristics (relief, slope, aspect) using remote-sensing data and the status of ecological recovery is represented by ecological indicators measured through field surveys. The results indicate strong correlations between landform heterogeneity indices and native vegetation species richness with sensitivity to the spatial scale of investigation. It is recognised that climate, substrate and rehabilitation practices act as primary drivers of rehabilitation success. However, the results indicate that, in some examples, landform heterogeneity (heterogeneity in relief and slope angles) contributes up to 30 to 50?per?cent of the variance in native vegetation species richness. While the primary drivers of ecological recovery are difficult to control over extensive areas and extended time periods, landform heterogeneity provides a tool to indirectly control the micro-environmental parameters to improve ecological recovery. Reducing the uncertainties in the choice of ecological and landform indices and the degree of landform heterogeneity suitable for particular rehabilitating landscapes would be site specific. The introduction of desired landform heterogeneity may provide a very effective tool for significant improvement in ecological rehabilitation across broad-scale post-mine landscapes, an outcome of benefit to industry, government and local communities.CITATION:Datar, A and Mulligan,?D,?2014. Do we need to change the way we set up the stage?, in Proceedings Life-of-Mine 2014 , pp 29–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer' s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By A. W. Worcester

The plant is designed to produce 60,000+ tons of refined lead per year from a nominal feed consisting of 110,000 tons of SLI and industrial batteries, and 10,000 tons of lead contained in drosses and scrap. The plant will also produce as by-products polypropylene chips and detergent grade sodium sulfate, using the Engitec Impianti CX Technology. The battery separation circuit will consist of a battery breaking hammermill and a vibrating screen with water sprays to separate the battery paste from the grid metal and other battery components. The battery components, consisting of ebonite, and separator materials, will be separated' from the grid metal and classified with the use of hydrodynamic water separators. The battery paste will be treated with sodium carbonate to produce a lead carbonate paste for smelting in a reverberatory furnace. The slag from the reverberatory furnace will be campaigned through a traditional primary blast furnace to produce hard lead. The sodium sulfate liquor from the lead carbonate filtration step will be crystallized to produce anhydrous sodium sulfate. The metallic grid metal will be treated through a small rotary smelter of the Engitec design to produce a hard antimonial lead. The plant's scheduled to be commissioned 12 months after receipt of all of the Federal and state permits. The plant will be integrated into the Buick Primary Lead Smelter, located in the center of Missouri's New Lead Belt, at Boss, Missouri. This will allow The Doe Run company to fully utilize all of its existing assets.

Jan 1, 1990

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By H. E. Doerr

THE writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to he that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities: Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and air-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250° F. (1235° C). Approximately 1 min. was required to forge under the steam hammier to 1 ¼ in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders ½ in. (17.7 mm.) in diameter and ½ in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. No in-formation was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by

Jan 1, 1919

By Isobel Clark

The problem of the estimation of ore reserves is essentially a simple one to describe. Given a set of sample data, at specified locations within a deposit, how can we estimate the value (or quantity) of ore in unsampled areas. The question may be posed of a whole deposit (global) or it may be more desirable to estimate smaller volumes within the planned mine area, e.g. stopes or blocks (local). Many methods have been evolved to tackle this problem, from hand-contouring of values by the mine geologist to extremely sophisticated geomathematical analysis. The main difficulty with any estimation method in this context is that it is almost impossible to check whether the "predicted" value bears a close relationship with the "actual" value. The only reliable way to decide if an estimation method has "worked" is to test the eventual value of ore against the predicted value. This is, more often than not, impossible - even allowing for the time factor involved. To know the "actual" value of a mined block it has to be sampled intensely, and these values with their positions recorded accurately. Alternatively, blocks may be passed through the concentration process individually and these results recorded. In most producing mines neither of these alternatives are practicable or seen to be-important. Another problem with comparing in-situ (so-called) mineable reserves with production figures is the introduction of many variables into the concentration process -- dilution, wastage, possible stockpiling, mill recoveries and so on.

Jan 1, 1979

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By W. Armstrong Price

INVESTIGATION by German chemists during the World War showed that particles of iron oxide form rapidly in iron pipes carrying hydrogen gas under pressure when the gas contains small amounts of water. Under these conditions, the gas frequently exploded when expanding into a dirigible. The explanation of the explosions lies in the building up of a charge of static electricity in the flow just beyond the orifice and the ignition of the gas by a spark accompanying discharge of the electricity. Friction between the moving particles and the pipe generated the electric charge, which was manifested by a pale blue glow formed in the flow at pressures above two atmospheres. In one experiment, this glow, at eighty atmospheres, extended for a distance of forty to fifty centimetres, but did not ignite hydrogen and air mixtures until the charge was col-lected by a conductor and discharged across a gap between electrodes placed at the side of the column of gas. Autoignition did not occur when this discharge was effected at a distance from the gas column, nor if the gas used was thoroughly dried and free from impurities. The electric charge has been studied by placing various wire and screen conductors in the outcoming stream of gas, Guest having summarized these experiments. The application of these conclusions to fires in petroleum and natural gas issuing uncontrolled from wells is made in the following paper, citing the ignition of a wild gas well in Texas.

Jan 1, 1936

By B. W. Cavender

Capital investments are made for a variety of purposes, from providing incremental capacity at existing operations to developing and implementing new technologies intended to radically improve a company's capabilities. These projects generate very different business opportunities and create value in distinctive ways. For incremental improvements, the capital budgeting process assures at least a loose fit between short-term goals and readily available resources. However, the criteria used to evaluate capital projects often prevent a company from committing to more aggressive goals that lie beyond the firm's current abilities or resources. Such projects may not have clearly identifiable future cash flows, and the degree of interaction with other projects and the nature of the risk incurred may be difficult to estimate. Additionally, by focusing only on quantifiable benefits, the budgeting process often fails to recognize "soft" improvements such as increased operating flexibility or new knowledge generated by such projects. By rejecting these projects, the capital budgeting process may actually harm the company's future competitive position.

Jan 1, 1998

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute of Occupational Safety and Health recently performed a laboratory study to evaluate which factors on an enclosed-cab filtration system are most significant. The various factors evaluated were intake filter efficiency, intake air leakage, intake filter loading, wind infiltration, use of a recirculation filter, and the use of an intake pressurization fan. The result of this laboratory testing has shown that the two most important factors for an effective filtration system on an enclosed cab were the efficiency of the intake filter and the use of a recirculation filter. A higher-efficiency intake filter considerably increased the quality of the intake air that was delivered into the enclosed cab. It also was determined that air leakage around the intake filter notice-ably reduced its air cleaning effectiveness. The second key factor is the use of a recirculation filter, which was shown to improve the air quality in the enclosed cab by six to 12.7 times more than the intake filter alone. The reason for the significant improvement was that the cab air was constantly drawn through the recirculation filter, thus continually filtering the dust out of the air.

Jan 1, 2010

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006