Search Documents

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By Garg. D.

Premixed bronze powders are widely used to produce a wide variety of P/M components including bearings and bushings by the powder metal industry. The physical and mechanical properties of sintered bronze components such as dimensions, strength, microstructural characteristics, and sintered density are well known to change with sinlering furnace design, particle size distribution in powders, green density, preheating and sinlering time" and temperature, and protective atmosphere flow rate. " However, not much is known about the effect of protective atmosphere composition on physical and mechanical properties of sintered bronze components; This paper describes effects of protective atmosphere composition and sintering temperature on physical and mechanical properties of sintered bronze components

Jan 1, 1996

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By Julia R. Budden, Peter A. Spencer

Bacterial oxidation processes have often been repo1ted as releasing large amounts of energy so that a large scale operation would require cooling to maintain the required operating temperature for the bacterial culture. These reports are based on the chemical heat release which in some eases has been adjusted for the energy required to fonn the mass of bacterial cell matter per unit volume of solution. There are two flaws in this approach for calculating energy release in the fonn of heat. The first flaw is that it only considers the bacteria in solution. The second assumption is that the only bacterial reaction is the fonnation of cell material and others such as energy for respiration and locomotion are not considered.

Jan 1, 1992

By F. B. Eiseman

IT is desired -to determine the effect of the extent of bank repairs on the final slag volume in acid electric steel-melting practice. It is understood that the repairs stud- TABLE I-Summary of Effect of Bank Repairs on Slag Volume [ ] ied here are necessary and the amount of sand added is that needed to maintain hearth and banks in a satisfactory condition. In this way the effect of repair materials on the amount of slag tapped would be found with a reasonable degree of accuracy. Ten heats were made for this study with careful attention to a uniform charge. The steel was the usual grade B and melting was carried out in a 3 1/2-ton top-charge Lectromelt furnace. Melting practice in all cases was the same-complete oxidation, with recarbonization by means of low-silicon pig iron.

Jan 1, 1947

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By William Brinkman, Mark Jolly, Nasim Soleimanian, Karl Dearn, Oliver Brinkman

"Glass manufacturing is a heat intensive process. There is a direct correlation between the batch distribution techniques and the furnace energy consumption, productivity, and quality of the glass manufactured. All four major segments (float, container, fibre, and specialty glasses) would benefit from using an optimised batch distribution technique where possible. Oscillating batch chargers (OBC) have been in use since the early 70s, despite their superior batch shape, coverage, and in turn positive effects on the energy consumption and productivity of the furnace they are almost exclusively used in container glass manufacturing. The OBC’s main difference compared with other charging methods is its ability to directly influence the batch initial velocity. This paper reports on results achieved in CFD models (GFM) used to study effect of the machine on the overall energy consumption in the doghouse and the melt space.IntroductionGlass manufacturing can be divided to four major segments float glass, container glass, fiberglass, and specialty glasses. The financial cost of manufacture, its impact on the environment, lack of standardisation and mounting pressure imposed by the authorities for reduction in emissions means that the industry and its suppliers are utilising CFD modelling in order to tackle these challenges. The need for high temperature to create and maintain the viscous flow, homogenisation of the glass melt, and maintenance of the process to allow continuous output of glass of the right quality are the contributors to the energy intensive activities that are involved in continuous glass manufacturing. This in turn has resulted in design of large container glass furnaces which have high energy consumption, low specific performance, and high CO2 emissions where the most efficient furnaces in the container glass sector have a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch making even very small improvements in efficiency by operation optimisation a value adding activity [1-14].The theoretical calculated energy required to melt glass is 2 to 3 times less than the energy actually used to melt glass as a result of glass melt passing a zone 5 to 8 times before leaving the tank.[8]. This causes contamination as the result of mixing between the completely molten glass free from bubbles returning to the batch area where there is freshly molten non-homogeneous glass, still containing very large numbers of bubbles and un-molten batch. At high temperature some components are dissolved rather than melted. Given that an un-molten batch is a good thermal insulator, it can be transported a long way into the furnace, increasing the need for homogenization which also increases the glass residence time of glass melt. This is why large unbroken strings of batch should be avoided, as should an overall blanket without gaps."

Jan 1, 2014

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By D. J. Sweet, B. Seymour, T. M. Emery, M. Armatys, J. P. Bourgeois, W. Johnson

The Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) has partnered with a narrow vein, hard rock underground mine to research the effects of the binder content on the elasticity and post-peak ductility of cemented hydraulic backfill (CHB). This is part of a larger study to enhance the long-term integrity of ground support in underground mines. As mining advances deeper and stresses increase, CHB mix designs will benefit if they can be modified to handle higher levels of strain which are induced by an increased stope closure, typically affected by a reduction in stope width and increased mining depth, or through dynamic loading resulting from a local seismic event. This portion of the research examined the impact of reductions in binder and their impact on Young’s modulus, peak strength, and post-peak ductility.

Mar 2, 2022

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By A. W. Khair, M. Ahmad, L. D. Gehl

"This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a more dusty environment.IntroductionThe high demand for coal production has increased the need for mechanized coal cutting in underground coal mines. Continuous miners have been used in the United States of America for nearly four decades and now presently more than 2000 are in operation. Almost half of the underground coal production of the country is by continuous miners. Today, competition in the coal industry has increased, due mainly to market conditions and legal restrictions, thus placing an emphasis on production, efficiency, and safety. The use of continuous miners has resulted in the generation of respirable coal dust which causes black lung in mine workers. On the other hand, bit wear presents a serious problem as it affects productivity and economy.Much research in the put has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in the cutting process. Recently, dust hazards in underground coal mines as a result of coal cutting has been a great concern to mining engineers as well as environmentalist of the country. In past, much emphasize has been given to fragmentation mechanics (Khair et al, 1989), dust generation due to regrinding (Khair and Xu, 1991) and dust generation due to bit wear (Khair, Xu. and Ahmad, 1992). These studies concluded that dust concentration increased considerably after a bit weight loss of 7% and thereafter the bit should be replaced. Thus, legal restriction by the Mine Health and Safety Administration for the respirable dust concentration in underground might be a factor deciding the level or rate of production using continuous miners. While efforts in research are on reducing dust generation, it is also important and relevant to study bit wear in more detail.Bit wear is affected by three major groups of parameters: (1) machine operating parameters, (2) insitu conditions and (3) properties of rock. Again, past studies have shown that depth of cut, material of tool, position of water jet and velocity of the rotating drum are very important machine operating parameters. The content of the rock/coal material is important as bit wear is usually due to abrasion or adhesion. Diffusive wear becomes dominant only when the temperature exceeds the sensitive range i.e critical temperature. Mechanical tools have indicated that a rise in temperature is a function of drum velocity, properties of cutting material (rock or coal) and properties of tool. Bit wear due to chemical reaction and oxidation art almost negligible in coal cutting."

Nov 1, 1995

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017