Search Documents

By Y-B Kang, J H. Park, J Park

In order to understand the effect of oxygen injection into the molten metal on the valuable metals (VM) recovery and interfacial phenomena, several high-temperature experiments were conducted using a high-frequency induction furnace with a quartz tube as the reaction chamber at 1673 K. Copper-based waste printed circuit board (PCB) that contains some impurities was selected as the end-of-life resource. CaO-SiO2 based pre-fused slag and oxygen gas were used in present works. The composition change and microstructure of the samples were analysed. As oxygen was injected into the system, impurities were rapidly removed. After the removal of impurities, continuously injected oxygen lowered interfacial tension between liquid slag and liquid metal. Lowered interfacial tension induced Cu loss into the slag.

Aug 21, 2024

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By H. M. O?Harra

Experiments have shown that the use of enriched air would be of particular benefit in the roasting of zinc ores for the manufacture of sulfuric acid. Enriched air increases capacity of furnace, decreases fuel consumption, and increases SO2 content of roaster gas. THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper distribution of heat in the furnace;1 the volume of enriched air,

Jan 3, 1924

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By Hiroyuki Matsuura

The effects of P2OS or Na2O addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at I 773K by isotope exchange method 1-6. The rate constant decreased with increasing P2Os content of molten oxides and the residual rate constant was observed at high P2OS content. On the other hand, the rate constant increased with increasing Na20 content for FexO-SiO2 melts, The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Hiroyuki Matsuura

The effects of P20S or Na20 addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at 1773K by isotope exchange methodl-6_ The rate constant decreased with increasing P20S content of molten oxides and the residual rate constant was observed at high P20S content On the other hand, the rate constant increased with increasing Na2O content for FexO-SiO2 melts. The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By M. S. Seehra, R. S. Pandurangi

"Investigations of the infrared spectra of crystalline and amorphous silica particles of different sizes (0.05, 5, 10, 15, 30, 45, and 260 um) in the range of 400-4000 cm-1 using Fourier transform infrared/photoacoustic spectroscopy we reported. The change in the intensity I of the signal with porosity e of powders follows the e/(1 - e) dependence for strong bands and e dependence for weaker bands as pre¬dicted by the theory of McGovern of al. For strong bands, I also follows the empirical relation I ~ D-n, where D Is the particle diameter in cm and n = 0.34-0.42. The anomalous positive frequency dependence of I on the modulation fre¬quency f observed for the stronger bands in the 45-pm and 260-pm particles Is believed to result from saturation. Some observations on the effect of changing the background from (carbon black) powder to pellet are also made.INTRODUCTIONSince the publication of the Rosencwaig—Gersho (RG) theory on the photoacoustic effect in solids (1, 2), Fourier transform infrared/photoacoustic spectroscopy (FTIR/PAS) has become an important technique for obtaining the IR spectra of surfaces and materials in their natural state (1-12). In the one-dimensional RG theory, the incident radiation, modulated at frequency f, is absorbed by the material to a depth pp = 1/B (B = absorption coefficient), thus setting up temperature variations in the material. These variations heat the adjacent gas/solid interface leading to the pressure fluctuations of the gas above the sample, which in turn is detected by microphone as a PA signal. The thermal wave originating from no deeper than the thermal diffusion length(2k/npcf) 1/2 in the material contributes to the PA signal (here k, p, and c are respectively the thermal conductivity, density, and specific heat of the material). Since u2, can be varied by varying the experimental parameter f, depth pro¬filing by PAS is possible and a number of papers on this subject have appeared in recent years (2-10). Another im¬portant phenomenon is saturation which occurs when the material thickness 1> u> us (1-12).The original promise of PAS for use with powder samples, without the need to ""prepare"" samples as in FTIR spectros-copy, has not yet been fully realized because of several com¬plications. Theoretical works by Monchalin et al. (13) and McGovern et al (14) showed that the interstial gas in the voids of the powders can act as amplifier and that, for the same mass, a finer powder is expected to yield higher PA signal than a coarser powder. Although in a number of earlier studies (15-21) an increase of PA signal with decreasing particle size has been observed, a quantitative check on the equations developed by McGovern et al. (14) has not yet been made. It is necessary to understand the particle size effects in PAS if the promise of PAS for IR spectroscopy of powders is to be realized. In this paper, we report results of a detailed study on the PAS of silica powders for the particle size range of 0.05-260 um and compare the results with theory (14). We have also investigated the frequency dependence of the variousIR modes in these powders and show that the saturation phenomenon affects at least some of the observations. Some observations on the effects of pellet vs powder background are also reported (22-24). Details of these findings are presented and discussed in this paper."

Jan 1, 1990

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By F. F. McINTOSH

STEEL is a general name applied to the alloys of iron and carbon. These alloys always contain , other elements such as manganese, silicon, sulfur, and phosphorus. Manganese and silicon are usually considered to be alloying elements. Sulfur and phosphorus are regarded as impurities. Tradition has damned them both and, in addition to classifying them as impurities, has established the general impression that many of the ills of steels are the result of the presence of one or both of these elements. Metallurgists are inclined to question the soundness of this tradition. The fact that one blast-furnace plant is devoted entirely to the production of ferro-phosphorus which is used to rephosphorize basic open-hearth steel, and that sulfur is added to many heats of steel, indicates that these so- called impurities might also be classed as alloying elements, and that the tradition which damns them may not be altogether fair and well founded. A critical search through the technical literature on the effect of phosphorus on steel will disclose many references to its harmful effect. Most of these are general in character, but there has been a strong tendency to accept this traditional belief in the harmful effect of the element.

Jan 1, 1926

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By Charles David

This work aimed at evaluating the effect of pre-strain of Lean Duplex UNS S32304 on anodic dissolution and hydrogen evolution reaction rates in acidic chloride media. Interrupted tensile testing was employed in order to generate different deformation levels. Potentiodynamic experiments allowed to detect a decrease on the cathodic and anodic reaction rates as a consequence of plastic deformation. A non-linear evolution of corrosion rates was observed, probably as a consequence of the evolution of specific dislocation structures in the material. Strain also caused a slight ennoblement of the ferritic phase, while austenite became a little less noble. These behaviors are analyzed in terms of residual stresses, characterized by X-ray diffraction.

Aug 17, 2017

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By K. Adam

Grinding in steel mills adversely affects the flotation of pyrrhotite. The electrochemical nature of inter action between pyrrhotite and active metals was investigated by contacting pyrrhotite with platinum at different applied potentials. Flotation tests, scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were wed to examine the surface properties of pyrrhotite. The formation of hydroxide or oxide and sulfate species of iron through the oxygen reduction reaction at the cathodically polarized surface of pyrrhotite was shown to be the mechanism responsible for the reduced floatability of pyrrhotite.

Jan 1, 1985