Search Documents

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By P. J. Brereton-Stiles, M. S. Rennie, N. Singh

Ferroalloy producers are large-scale users of electrical energy, which in many countries is in short supply and increasingly expensive. Preheating and/or pre-reduction using natural gas, recycled furnace gas or coal fines have lowered the specific use of electricity, but the high energy concentration necessary for most reduction processes can be achieved only by the use of high electric currents. Most countries have insufficient electricity to supply the demands of industry and the domestic consumer, particularly during certain periods of the day and certain times of the year. The generation and distribution of electricity is a large-scale expensive business, which is financed and managed directly or indirectly by government bodies in most countries. Both economic and political imperatives determine how much electrical energy is made available to whom and at what price. In South Africa demand is set to outstrip supply within the next few years, and the local supplier Eskom has moved from a traditional demand tariff pricing structure to a time-of-use tariff pricing so as to limit peak demand usage. This will mean a substantial increase in electricity cost to those users unable or unwilling to reduce consumption during peak periods. The optimal use of the available electrical energy depends both on the process, the furnace size, the configuration and infrastructure of each plant and its cost structure. As the cost and availability of electricity is set to change dynamically, the management of the situation becomes a real time control and optimisation problem. This paper discusses some the process and operational constraints associated with low- or no-load conditions and how to manage the situation. Electrode management will be one of the key issues.

Jan 1, 2004

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By Clark B. Risler, Walter E. Thomas

MILL planning must include electrical drives and a system to supply them. These should be considered at the time metallurgical and mechanical plans are being made. Because it is convenient, flexible, reliable, and economical, electricity is the accepted source for powering mill concentrating equipment. Ore-treating mills have grown to the point where a single mill has been built using 360 motors ranging from 1 to 1000 hp and totaling 50,000 hp. Such a system of electrical drives can be scattered over a square mile and employ 4000 to 220 v. Drive Motor Characteristics: Since ore processing is predominantly a continuous operation, very few of its drives require wide speed variation after initial adjustment. Consequently squirrel cage, wound rotor, and synchronous alternating current motors are most often used.

Jan 5, 1957

By Erich Sarapuu

Today's increasing needs for rapid excavation have stimulated efforts to break rocks without explosives. The application of electric energy for this purpose has been studied by a number of investigators. Following principles have been used in electrical rock breaking: 1. induction heating5 2. high frequency heating4, 14 3. microwave heating6 4. contact resistance heating9,12 5. resistance heating11,13 6. electron beam heating1, 3 7. plasma jet heating2, 8 8. arc heating7 9. condensor discharge energy14 In this paper the presentation of the principles of electrical fragmentation is limited to a process called "electrofracing". This technique uses electrical heating of rock by electrode contact resistance9 and resistance heating" phenomena. The electrically induced stresses inside of rock generate forces which break up the material. The fracturing of ore takes place by tensile stresses instead of compressive forces. The electric energy merely creates fractures in the rock and the separation of fractured material takes place by subsequent mechanical handling. Energy requirements in secondary breaking of iron ores have been about one to two kilowatt-hours per ton of ore. Power requirement is a function of the degree of fragmentation.

Jan 1, 1969

By F. G. Cottrell

(New York Meeting, February, 1912.) ABOUT a year and a half ago, at the San Francisco meeting of the American Chemical Society, in connection with the excursions to local smelting-works, I had occasion to show some lantern-slides illustrating the recent commercial development of electrical methods for precipitating the suspended matter from smelter-smoke, the underlying phenomena of which were clearly brought to the attention of the technical public by Sir Oliver Lodge as long ago as 1884. In the Journal of industrial and Engineering Chemistry, August, 1911, most of these views were reproduced, together with an account of the work from its beginning up to July, 1911. To-day I wish particularly to show you some of the further developments of the work since that time; but in order to make these clear they will be prefaced by a brief abstract of the article above referred to. The removal of suspended particles, front gases, by the aid of electric discharges is by no means a new idea. As early as 1824 we' find it suggested by Hohlfeld 1 as a means of suppressing ordinary smoke, and again a quarter of a, century later by Guitard.2 These suggestions, which do not seem to have stimulated any practical study of the question, were soon entirely forgotten, and only brought to light again by Sir Oliver Lodge,3 many years after he himself had independently rediscovered the same phenomena and brought them to public attention 4 in a lecture before the Liverpool Section of the So-

Jul 1, 1912

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By J. C. Cawley, G. T. Homce

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Jan 1, 2013

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By Nelson Lawrence

An Electrical Risk Management/Inspection Program has been designed specifically for the mining sector in order to provide electrical code expertise and systemic gaps in electrical systems. Goals include improved safety and productivity, reduced injuries and help to enable businesses to better comply with the electrical codes and regulations that govern them. The Electrical Risk Management/Inspection Program is now recognized by some of the world?s largest mining organizations. Since June, 2001 these electrical safety advisory services have been available to underground and surface mine sites throughout Ontario and are now offered throughout Canada and around the globe. This program is also currently being applied to review new electrical installations for mine construction projects thus improving the safety and reliability of mine site electrical systems.

May 1, 2006

By M. J. Sheriff, D. H. Smith, W. Macdonald

The paper outlines the basic procedure used in electrical system planning and design. Consideration is given to the use of applicable codes and standards, development and use of a system One Line Diagram, power availability, load requirements and power factor. Also discussed are the factors influencing the selection of power supply and distribution arrangement, voltage levels, system grounding, distribution and utilization equipment such as switchgear, transformers, motor control, cable systems, motors. Short circuit calculation methods and system protection are discussed.

Jan 1, 1978

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976