Search Documents

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By J. R. Kadambi, C. Shingote, J. Furlan, R. Ke

"Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multi-phase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations, based in some part on the respective current-available theoretical models, and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone was explored with the aid of both computational and experimental techniques (Particle Image Velocimetry). In this study, the flow field with an air core has been investigated; in essence, the research was a two-phase problem, which caused some challenges on both the computational and experimental sides. Two turbulence models were used in the numerical calculations: the Reynolds Stress Model and Large Eddy Simulation. The computational studies are mainly focused on the prediction of the dimensions and shape of the air core. Different section planes of the hydrocyclone were selected as planes of interest and then were divided into several fields of view (FOV) for PIV measurements. Two dimensional experimental velocity vector maps were obtained in each of the fields of view. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. Keywords: Computational fluid dynamics (CFD); Hydrocyclone; Particle image velocimetry (PIV); Reynolds Stress Model (RSM); Large Eddy Simulation (LES). INTRODUCTION A hydrocyclone is a device used to separate a solid-liquid, liquid-liquid, solid-gas, or liquid-gas suspensions into at least two separate density or particle size components. Hence, the flow field of the hydrocyclone is generally considered a multi-phases flow system. Application of hydrocyclones have been used in numerous industries including oil, drilling, metal working, and mineral processing since 1891, when E. Bretney obtained the first patent for the predecessor design of all contemporary hydrocyclones. A modern hydrocyclone typically consists a cylindrical section at the top where the liquid is being fed tangentially, and a conical chamber attached to the bottom of the cylindrical section, as shown in Figure 1. The characteristics of the feed stream that is injected into the cylindrical chamber play a significant role in hydrocyclone operation. The inlet is tangential relative to the cylindrical chamber and hence causes a centripetal force in the flow field which is considered as the primary separation mechanism."

Jan 1, 2017

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By Y. Jiang, B. Li, R. Liu

"In this study, laboratory flow tests were conducted on 2-D artificial rock fracture network models containing a single intersection constituted by two inlet and two outlet branches. Three models with different intersecting angles of 60°, 90° and 120° were tested using both dye solution and distilled water. Constant flow rates were imposed on one inlet, and the flow patterns in the fracture intersections were captured by using a CCD camera. The test results were compared with the predictions made by numerical simulations that solved the Navier-Stokes equations. The results revealed that when Reynolds number (Re) is as low as less than 1, the intersecting angle has negligible influence on the flow rate of each branch and the flow patterns within a fracture intersection. As the interesting angle ? and Re (e.g., from 10 to 200) change, the normalized flow rates of different outlet branches change significantly, due to the inertial effect of fluid flow. These changes could be represented by a series of mathematical expressions involving Re and ?, which could be applied to fracture network models to improve their prediction accuracy on hydraulic properties (e.g., permeability and breakthrough curves of particles) of rock masses. INTRODUCTIONCoupled stress, flow, heat and mass transport are the corner stone subjects for many geoscience and geo-engineering disciplines, such as geological disposal of radioactive waste and geothermal energy exploitation. Many outstanding issues need to be investigated to enhance the knowledge on these subjects, and specifically more in-depth research in testing and modeling of the fluid flow in fractured rock masses is needed. In recent years, discrete fracture network (DFN) models have been extensively used to study the fluid flow and mass transport behaviors of fractured rock masses (e.g., Min et al., 2004; Zhao et al., 2011). In these models, each fracture is usually represented by a parallel-plate model, in which fluid flow exactly follows the cubic law. Therefore, comparative flow rate in each outlet branch of an intersection in these models only depends on its aperture. In reality, due to the surface roughness of fractures, the magnitude of mechanical aperture is usually larger than that of the hydraulic aperture of each fracture (Li et al., 2008; Xiong et al., 2011), and abundant flow patterns could exist in an intersection, influenced by its geometry, varying with changing Reynolds number (Re) (Kosakoswski & Berkowitz, 1999). Recent studies have also revealed that different mixing patterns might exist at a fracture intersection, bounded between streamline routing model and complete mixing model, that determine the final distribution of solutes in fractured rock masses (Johnson and Brown, 2001; Park et al., 2001). Numerical simulation has been the principal method adopted in previous studies, and the studies conducting flow tests on intersected fractures are less reported (Wilson & Witherspoon, 1976; Johnson and Brown, 2001). In this study, laboratory flow tests and numerical simulations by solving the Navier-Stokes equations were conducted on 2-D models containing a single intersection constituted by two inlet and two outlet branches, intersected at different angles. The main objective is to study the influence of intersecting angle on the flow behavior of the intersected fractures and the variations of flow patterns and fluid redistribution in each model along with the changes of the Re and the intersecting angle ?. The influence of surface roughness was not considered."

Jan 1, 2015

By I. V. Filippova, Y. Foucaud, M. Badawi, L. O. Filippov, S. Lebègue

To optimize the flotation of Ca-minerals, their separation contrasts were investigated by coupling experimental and theoretical techniques. We showed that they mainly rely on structural properties such as the Ca-Ca distance on their exposed surfaces but also on the ability to control the intermolecular interactions. An optimized composition of the carboxylic collector by calculating the collector-mineral and the intermolecular interactions was developed. Blending the saturated acids and non-ionic molecules with a fatty acid collector significantly increases the flotation selectivity between scheelite (CaWO4) and fluorite (CaF2). The theoretical results were validated by experimentally improving the separation contrast between Ca-minerals. After the tests of several depressants and collectors, the best depression of gangue Ca-minerals (fluorite, apatite and vezuvianite) was found by combining sodium silicate and sodium carbonate. Keywords: Ca Minerals, Fluorite, Scheelite, Carboxylic acids, Unsaturated Acid, Fatty acids

Jan 1, 2020

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By W. E. Wallace, P. Bolsaltis, M. J. Keane, B. L. Rauaboni

Thermal treatment of respirable size silica dust samples results in marked changes in their hemolytic activity. These changes can be correlated with changes in the characteristics of the particle surface as measured by infrared spectra, zeta potentials, and specific surface area. Silica samples from various sources (Min-U-Sil, fumed silica, and a NIOSH standard sample) were heated or calcined at temperatures ranging from 100-1095C. The hemolytic activity of the crystalline materials decreased after thermal treatment. The behavior of the fumed material was found to be more complex. Material of very large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. Tre changes in hemolytic activity can be related to infrared spectra and zeta potentials of the materials. The absorption band in the 3200-4000 cm-1 frequency region of the fumed material disappears upon heat treatment while a sharp, characteristic band at 3750 cm-1 increases in intensity. Zeta potential measurements conducted in the pH range of 2.0-10.5 exhibit a unique change in zeta potential v.s. pH profile with heat treatment. These findings indicate that the removal of active surface silanol groups by calcination results in reduced cytotoxicity, as measured by a hemolysis test.

Jan 1, 1988

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919