Search Documents

By Osamu Shoji, Mamoru Kato

In order to continue improving the quality of telecommunication services to meet the expectations of the people and to increase reliability in the case of emergency such as disasters, Nippon Telegraph and Telephone Public Corporation (NTT) is now constructing cable tunnels which connect main urban telephone offices. However, almost all the large cities in Japan are built in river deltas, so that their chief underground features are low strength fluvial deposit and a high ground water level. In this saturated soft ground, the ground surface at an installation site has occasionally subsided through deep excavations for cable tunneling construction. As these settlements have sometimes caused accidents, especially in densely populated large cities, NTT has made much effort to avoid such accidents. These accidents have occured mainly in flexible sheeting due to its inward movement. Therefore, after the investigation into forecast method of sheeting deflection with accuracy, NTT has reserched a system which forecasts ground surface settlements. This paper describes an outline of the ground settlement forecast system and practical example on the site.

Jan 1, 1979

By M Armony, J F. C L Costa, J C. Koppe

Linear kriging methods fail to estimate local grades and local reserves for highly skewed variables due to three reasons: it uses only part of the available data information, it has no physical principles associated with the mathematical proceedings to minimise the problems, and it works with continuous variables while data are discrete because of the limited precision of any equipment. The techniques commonly used up to now to solve the highly skewed variables estimation problems were unsuccessful, unless mathematical rigor is abandoned. Even the method of multiple indicator kriging is not satisfactory. This paper presents a new framework, the field parametric geostatistics (FPG) that transforms noisy variograms into well-behaved variograms and justifies mathematically empirical procedures commonly used, as trimming or capping arbitrarily very high values. The method, when applied to non-skewed variables, yields similar results to classic kriging. The methodology is illustrated in a case study at a gold deposit in Brazil, and compared to results obtained by usual techniques.

Sep 26, 2011

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

By John I. Sharpe

Masses of pyritic copper and zinc ores are entrapped along the contact zone between two volcanic groups in the Matagami area. The upper limits of the sulphide concentrations tend to form concordant contacts against lava or cherty tuffite units of the younger group; the lower extremities tend to either follow transverse structures or merge with zones of dispersed sulphides. The sulphides are deformed and intruded by folded dykes. Close relations between metallization boundaries and volcanic lithology and stratigraphy, and a preliminary investigation of the fabrics and crystallization temperatures of the sulphide masses, suggest that the copper and zinc (but; not necessarily all the iron sulphides) were emplaced at h1gh temperatures during volcanism in near-surface lithological-stratigraphic traps. Introduction T HE Matagami area is centered 120 miles north of the Val d'Or and Noranda camps in north-western Quebec. For the present purpose, it is considered to comprise a 155-square-mile area in Isle-Dieu, Galinee and Daniel townships which encompasses the main sulphide masses. Airborne geophysical surveys within this area in 1956 led to the discovery of a large sulphide body -the.

Jan 1, 1965

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

By M. P. Ristenbatt, E. K. Holland-Moritz, K. Metzger

A new post-disaster signalling system for the Bureau o Mines, using through-the-earth EM propagation, was successfully field-tested in the Lake Lynn test mine. Successful detection at an estimated input SNR of -30dB was accomplished using a coherent integration time of 4.46 minutes. The transmitted waveform consisted of a repeating pseudonoise maximal length sequence phase modulating a 1950Hz carrier. The receiver used a sliding-window matched filter, optimal for signal known exactly except for phase and starting time, implemented via a special purpose processor. Parallel processing permits adaptive signalling, where the detection (integration) time is determined by the actual input SNR encountered. This field test demonstrates a trapped miner detection system that is about 36dB more sensitive than a current pulsed system. This increased sensitivity permits some desired combination of increased range, shorter detection time, and reduced transmitter power or antenna-size. The combination of pulse-compression-type-signal, coherent integration, parallel-processing, and output peak-detection algorithms permit implemention of an ultra-reliable detection system. The same combination is compatible with digital Pulse Position Modulation and Emitter position location strategies.

Jan 12, 1983

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Michael J. Beus

The National Institute of Occupational Safety and Health-Spokane Research Laboratory (NIOSH-SRL) have developed a Shaft Conveyance Monitoring System (SCMS). Assessment of current hoisting technology has shown that monitoring wire rope tension and conveyance position and load directly from the skip or cage top offers several significant safety, production, and maintenance advantages. The SCMS consists of conveyance position and guide displacement sensors, a battery power supply and charging system, and a new sensor to measure hoist rope tension. This device provides a warning of the occurrence of ?slack rope? a particularly dangerous condition. A 2.4 GHz radio link transmits data to the hoistroom. A reduced scale hoisting test facility has been constructed to test these components prior to field trials. The advantages of monitoring wire rope tension and conveyance position and load directly from a skip or cage top will be discussed. Field tests are underway in full-size shafts to refine the concept and evaluate long-term reliability and maintenance requirements. Application of this technology may result in decreased maintenance costs as well as safer, more productive hoisting operations.

May 1, 2001