Search Documents

By Zhi Yang, Ahmad Ghahreman, Farzaneh Sadri

Impurity removal is a very important stage of the hydrometallurgical treatment of rare earth elements (REE) processing circuit, which is performed after water leaching of the acid baked REE concentrate. Lime neutralization has a high efficiency in removal of impurities and is the preferred process due to its economic advantage; however, the process has its own problems, such as the production of large volumes of gypsum and co-precipitation of REE with gypsum, i.e. REE loss. This work deals with the effect of several additives (cetryltrimethylammonium bromide (CTAB), polyvinylsulfonic acid (PVS) and polyacrylic acid (PAA)) on the uptake of REE by gypsum from synthesized acidic solutions. The main purpose of this study is to investigate the changes in the crystalline morphology of gypsum precipitated by the addition of crystal habit modifiers and to determine the crystal changes’ effects on the uptake of REE by gypsum. In this regard, different concentrations (0.2, 2 and 5 g L−1) of above-mentioned additives were studied at room temperature.

Mar 1, 2018

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

Thermodynamics and kinetics? of the removal of Va elements (As,Sb,Bi) from copper were investigated 1n the fire relining by alkaline carbonate fluxes such as Li 2co3 , Na 2CO3 and K2CO3. The distribution coefficients of As, Sb and Bl between alkaline carbonate fluxes and mo) ten copper were ?obtained at 1200°C under the different oxygen potentials. As and Sb were easily removed from copper to fluxes as pentavalent oxide form. On the other hand, Bi was hardly removed except by a Ll2CO3 flux. The removal rates of Va elements from copper were also measured In the temperature range of 1150°C.- 1250°C. The removal rates of As and Sb were much higher than that of Bi. The removal rates of Va elements showed the same order of the distribution coefficients. The removal rate could be expressed by following equation. (1).

Jan 1, 1987

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Rodrigo Serna-Guerrero, Ted Nuorivaara

"As the demand of raw materials increases in a global scale due to demographic and economical changes, it is necessary to find technological solutions that improve current production processes in an efficient and sustainable manner. The main objective of this preliminary study is to evaluate the properties of foam produced with a cellulose-based molecule as an alterative to commercial frothing agents in flotation operations. There are two potential advantages identified with the use of cellulose-based additives for the proposed application: i) these chemicals can be produced from sustainable sources (i.e., non-edible crops), and ii) cellulose can be functionalized with chemical groups, in order to rationally modify its behaviour. In previous studies dealing with foam stabilization, it has been proposed that some functionalized cellulose species present a self-assembly mechanism at gas-liquid interfaces. Unlike typical surfactant-based frothers, cellulose molecules form networks around the bubbles that act as protective layers to the mechanical stress and to the occurrence of ionic species. This work studied the properties of foams produced in the presence of a partially hydroxylated cellulose molecule (i.e., hydroxypropyl methyl cellulose; HPMC) under various concentrations in a laboratory-scale column. A comparison with a commercial surfactant frother (i.e., Nasfroth 240) is presented, and a rationalization of the behaviour of HPMC in terms of foam properties (i.e., surface tension, bubble size, foam depth) is proposed. INTRODUCTIONThe search for green alternatives to chemicals produced from non-renewable sources has become a topic of major relevance in industry (Choi et al., 2015). As a chemical consuming industry, the mining sector faces now the challenge of adopting new processing technologies and strategies in order to achieve the future demands of sustainability. Evidently, a move towards green chemistry can only take place by identifying substitute molecules offering potential advantages in terms of recovery and grade."

Jan 1, 2016

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Wenqiang Bao, Qijie Zhai, Ting Wang, Shaobo Zheng, Huigai Li

The type of inclusions with different sizes in as-cast low carbon steel strip which is deoxidized by Si–Mn has been characterized by scanning electron microscope (SEM) and transmission electron microscopy (TEM). SEM observation and analysis suggested that the type of inclusions larger than 1 μm is manganese silicate. TEM analysis was carried out to investigate the composition and structure of nano-inclusions. Inclusions with diameter about 100 nm are manganese silicate, MnS–Si(Mn)Ox complex particles and isolated cubic Al2O3. Furthermore, HREM observations have revealed that there were two kinds of ultrafine particles in size range of 5–10 nm. One is spherical monoclinic Cu2S; the other is silicon-iron oxide particles with morphology of long strip. In addition, some thermodynamic calculations were performed to explain the corresponding relation between the type of inclusions and their size.

Mar 1, 2017

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004

By II Browne

After a decade of high copper prices, major mining companies are renewing their interest in purchasing operating properties and/or development of ore bodies. An existing operation carries with it a history that can present unique opportunities, while a greenfield operation allows for the establishment of a defined culture. Capital investments are distinctly different. A comparison of BHP Copper Robinson Operation, a greenfield property, and BHP Copper Tintaya Operation, a government owned Peruvian property, will provide insights into mining, concentrating and cultural differences between North and South American Operations.

Jan 1, 1997

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By C. W. Lockhart

Strength evaluation programs, based on sub- jecting a number of 5-718 inch (0.15 m) diameter core samples from highly fractured or poorly consolidated rock, to triaxial compression tests, have been successfully completed. An innovative approach was required since con- ventional methods with similar materials had not produced reliable results. Drilling methods were modified, and specially designed transparent core barrels were used. Sample preparation was successfully accomplished by using speciallydesignedtools and unorthodox hand- ling methods. Initial tests were carried out on weathered oxides from an open pit copper mine. The technique was later used successfully where the test material was weak, friable coal. The procedures used offer a practical method of testing weak materials where conventional methods would not be successful.

Jan 1, 1980

By J. D. Goodrich

Success of The Carter Mining Company's safety program can be primarily attributed to "total immersion" of all operating and staff personnel in program design and implementation. Currently, the Company operates two surface coal mines in Campbell County, Wyoming. Total employment is about 440 and current annual production is about 15 million tons. The safety program has evolved from one which was administered primarily by staff personnel (the Safety Department) to one which requires active participation by line management and operating personnel. Lost time accident frequencies have declined from a high of 1.86 per 200K hours worked in 1978 to zero in 1982. Reportable accident frequencies have declined from slightly over 5 to slightly over 2 during the same period. Analysis of program results indicates that the most important achievement by the company has been to gain strong commitment to safe operation by all employees. It is important that program format and content be frequently changed and modified so that: 1) The requirement for safe job performance is communicated well and often, 2) The safe job performance message is trans- mitted in new and interesting ways, and 3) Operating personnel participate in design and implementation of the program.

Jan 1, 1983

By Douglas F. Stevenson

Your committee doesn't assign any easy topics to us speakers. How do you define "successful" in what is essentially a losing game? I am reminded of the fellow who returned from a one-week vacation in Las Vegas, and proudly stated, "I only lost $150." To him, that was "success." I am afraid that workers' compensation is a losing game for employers, too, and success has to be defined in terms of how much or how little is lost. We have no chance of producing a profit for our employer. We will narrow down to some suggestions about conducting a workers' compensation program at the plant level, but first I want to discuss the general legal, social and legislative climate in which your plant program operates. Workers' compensation is a statutory program with its general parameters established by the legislature. These parameters are then amplified by the boards and commissions established to administer workers' compensation. What influences the legislature and the boards and commissions as they establish the framework in which we must function?

Jan 1, 1986

By Xiyu Gao, Yi Yang, Mark I. Pownceby, Shuiping Zhong, Miao Chen

In the present study, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray absorption near edge structure (XANES) spectroscopy, and Raman spectroscopy were used to investigate the effect of chloride ions on chalcopyrite bioleaching and chemical leaching at 25 °C. The leaching results show that the addition of chloride ions suppressed the dissolution of chalcopyrite in both chemical and bacterial leaching. In chemical leaching, the solution redox potential in the experiment without Cl− stayed in a range more suitable for chalcopyrite dissolution compared with experiments with Cl− . In bioleaching, the bacteria activity was suppressed by Cl− leading to low dissolution rates of Cu. Surface morphology and chemical speciation studies confirmed the formation of potassium jarosite on the surface of the chalcopyrite leach residues. In addition, S K-edge XANES indicated the formation of trace amount of elemental sulfur and covellite on the mineral surfaces.

By Rich A. Lamb, Paul J. Axtell, Michael K. Muchard

"Since 2010, the Minnesota Department of Transportation (MnDOT) has performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. All of the piles were 42-in diameter, open-ended pipes driven to practical refusal on sedimentary bedrock with D125-32 diesel hammers from three separate manufacturers. The rapid load test method in general accordance with ASTM D7383-10 (Statnamic method) was used along with high-strain dynamic testing and subsequent signal matching. Results of these tests indicate that the axial nominal resistance of these piles in compression is not controlled by geotechnical considerations when driven with an appropriately sized hammer and installation criterion. Rather, the predominantly elastic load-deflection behavior of the piles under compressive load suggests the axial nominal compressive resistance is controlled by the structural capacity of the pile. In all instances, the rapid load tests indicated a nominal resistance exceeding that produced by high-strain dynamic tests due to insufficient hammer energy to fully mobilize resistance. In all cases, the hammers used were able to easily install the piles through the soil overburden. Mobilizing a larger hammer simply to demonstrate high-strain dynamic resistance is not economical or practical. This paper presents the subsurface conditions at each location, the ensuing test results, and the ramifications for future projects in Minnesota utilizing large-diameter open-ended pipe piles.INTRODUCTIONThe Minnesota Department of Transportation (MnDOT) has recently performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. The four project locations described in this paper where pile load testing was performed are shown in Figure 1 and exist in the southeastern portion of Minnesota. The projects are all major bridges crossing the Mississippi River in three instances and the St. Croix River just above the Mississippi River in the other instance. The first project is the TH 61 Mississippi River crossing in Hasting, MN where two load tests were conducted. The second is the TH 36 St. Croix River crossing in Stillwater, MN where two load tests were performed. The third project is the I-90 Mississippi River crossing in Dresbach, MN where three load tests were conducted. The final project is the TH 43 Mississippi River crossing in Winona, MN where one load test was performed."

Jan 1, 2017