Search Documents

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By George W. Riter

Discussion of the paper of H. 0. Hofman and C. R. Hayward, presented at the New Haven Meeting, February, 1909, and printed in Bulletin No. 30, June, 1909, pp. 513 to 529. GEORGE W. RITER, Salt Lake City, Utah (communication to the Secretary*).-In their paper, Messrs. Hofman and Hayward deal with a branch of silver metallurgy that is on very uncertain ground, both as a commercial process and as a metallurgical science; moreover, its field is limited to few localities and to peculiar conditions. The literature on the subject is incomplete and full of conflicts. The paper under discussion clears u p no disputed points; on the contrary, because of hasty generalization, its tendency is towards further confusion. In Table I., the authors assume that each test-lot of 1,800 g. of ore contained exactly 5.499 g. of silver, that any variation in the quantity of silver recovered, however slight, should be ascribed to variation in the time of grinding. It is barely possible that the ore was mixed so uniformly as to justify this assumption; but those of us who know how difficult it is to get uniform samples of any ore in which silver mineral is present in rich particles will have a doubt on this point. The unlikelihood of getting absolutely uniform test-lots of ore also reflects on the data in Table II., on the effect of varying the amount of salt in a pan-charge. The authors say " The salt series was the last one that was investigated." This again raises a question as to whether the ore was split into test-lots at the time of sampling, or whether it was kept in bulk in such a way as to permit mechanical concentration of values before the end of the experiments. The conclusion following Table II.: " There is no reason, therefore, for going beyond six per cent. of salt," is hardly to the point. If we assume that salt is of benefit only when in solution, it follows that the relation between the quantity of salt

Mar 1, 1910

By C. R. Hayward, H. O. Hofman

I. INTRODUCTION. THE aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation: The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment that the present paper intends to deal. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization, by casting a thermal balance to find the ,distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In, lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a. summary of several tests will give the best method of operating.. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jun 1, 1909

By H. Hejny

The objective of the project is to construct and operate a pan-European underground drainage and minewater management research centre, which would be the hub for data gathering and dissemination in real time of new data to users for analysis and interpretation, as well as serving as a model for consistency, for other centres at key water management sites throughout Europe which would feed data in real time through the hub. The data from the centre will be essential for informing River Basin Management Plans arising from the EU Water Framework Directive, which is an important driver for the project. The implementation of this Directive sets out a requirement for all Member States to develop River Basin Management Plans for all water resource systems. The facility would be a major contribution to sustainable water management in Europe.

Jan 1, 2007

By L P. Trout, D G. Reid

PanAust Limited (PanAust) has successfully constructed and commissioned two mining operations in Lao PDR over the past decade and undertaken major studies for three new mine developments. The management of potentially acid generating mine waste and tailings in close proximity of local communities sensitive to water discharge quality have been recurring themes that have confronted PanAust’s project study, development and operational teams. Further compounding challenges, such as the effects of intense annual tropical monsoonal conditions, staging of embankment raises and regular lifting of spillway structures, integrating mine waste and tailings management into production plans and ensuring the long term stability of structures, have been addressed by implementing leading practice management solutions.A recognition of the criticality of managing the substantial business risks associated with these crucial activities led to the early establishment of a governance structure to ensure that the highest standards are embraced for planning and execution. Importantly, these are guided and monitored by a panel of highly experienced and qualified international specialists reporting directly to PanAust’s Managing Director – the Tailings Independent Review Panel. The stewardship process has been effective in identifying potential shortcomings in management systems and has led to enhanced executive commitment to risk informed designs, assurance and overall process rigour.CITATION:Trout, L P and Reid, D G, 2018. PanAust Limited’s approach to mine waste and tailings stewardship, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 135–155 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Tobar

The development plan (long-term plan) of El Teniente Mine, Codelco-Chile, includes 100 per cent primary ore, located at increasing depths, which may involve several difficulties related to the application of the current panel caving method, such as a high seismicity level, a coarse fragmentation and ore pass damage. Therefore, it is a strategic priority for the El Teniente mine, to design and to test alternative mining methods, at similar or lower costs to ensure an efficient and safe ore extraction. In this context, the Macrotrench method is developed, as a competitive alternative to the current method. The document describes the panel caving method, the experience achieved in the primary ore exploitation from the geomechanical point of view. It also describes the æmacrotrenchÆ method as an alternative to the current exploitation method. Finally, the comparative advantages of macrotrench in relation to panel caving are presented. The results obtained during the engineering stage include the following aspects:the mining design, the material handling, a geomechanical evaluation of the method, and a comparative analysis.

Jan 1, 2000

By E Rubio, N Morales

Currently, mine plans are optimised by using several criteria as objective functions, like profit, life-of-mine, concentration of some pollutants, mining costs, confidence level or ore resources, with consideration of constraints related to production rates, plant capacities and grades. Whilst this approach is successful in terms of producing high value production schedules, it uses a static opening sequence of the drawpoints and therefore the optimisation is made within the level of freedom left by the original opening schedule, and as a result it is far from the true optimal value of the project. This paper presents a model to optimise the sequence of drawpoint opening over a given time horizon. The emphasis is in the precedence constraints that are required to produce meaningful operational sequences considering the exploitation method (panel or block caving), physics considerations and logical rules. Further on, while it applies the standard approach of maximising net present value (NPV), it considers other targets for optimisation, like the robustness and constructability of the plans. Finally, it applies the model to real data to obtain feasible plans by means of this model. The first tests were done varying the production capacity of the mine.

Sep 26, 2011

By E. Pizarro

Division Andina has considered in its long range planning, the exploitation by panel caving method of "Third Panel" mine, which was started its production stage during the second half of 1995. This mine has two production levels, the first is grizzly level and another is L.H.D. level. Both sectors use the same haulage level where mineral is recollected through ore pass. For mineral loading and haulage its use 50ton diesel trucks combined with electro-hydraulic chutes. The automation has permitted what this operation is carrying out with remote control by driver's truck, in concordance to short range planning.

Jan 1, 1998

By R. J. Miller

Mechanized Roof Supports (MRS) have dramatically improved safety and productivity of retreat pillar mining in coal. Due to low capital cost and greater flexibility, retreat panels have in some cases approached the productivity of a longwall. Because of improved safety and rapid set-up time when compared to conventional timbering, MRS are driving a return to retreat pillar mining in many situations. This paper describes how panel layout can be optimized for safety and operational efficiency when using MRS for retreat pillar mining of coal. The potential for significant unit cost reductions will also be addressed.

Jan 1, 1996

By L. Casagrande, C. O. Brawner, D. L. Pentz, B. Kennedy, E. Hoek, H. Q. Golder, K. Barron

H. L. HAMMERSLEY, B. C. Dept. of Mines. I would like to ask Mr. Brawner if the direction that he measured in the boreholes with the camera was referenced to magnetic north? MR. BRAWNER. Yes, it was. However, there is one problem that you may encounter if the ore body is magnetic; the borehole compass will give erroneous results. Three procedures are available to overcome this. The first one involves the use of a gyro compass instead of a magnetic compass. The second technique developed by Christiansen in Salt Lake City, is to orient the core with the use of scribing knives. The third method is to remove the compass needle and place a steel ball in the compass case. The hole must be drilled at a slight angle off the vertical. The location of the steel ball, which will roll to the underside of the hole is photographed. A borehole directional survey is then made, from which the bearing of the steel ball relative to the axis of the compass can be determined. The joint orientation is then related to this bearing at all depths. J. ROBINSON, B. C. Dept. of Mines. It was stated this morning that there have been some recent developments that give us the ability to drill horizontal drainage holes and install drainage pipes more cheaply than in the past. Would Mr. Brawner tell us some of the new developments and methods of installing these horizontal drain holes? MR. BRAWNER There are two zones in which you may be concerned about installing drains; the first is in the overburden soil, the second is in the rock. Each area requires a different installation method. If the rock is fairly massive and the holes will remain open, the simplest procedure is to use standard air track equipment or a percussion drill. At one of the mines in the Highland Valley, drains up to 300 ft. long have been installed with a percussion drill at a rate of one drain per day. The costs were in the order of $2.30 and $2.40 per foot. If the rock is quite soft, such as in a serpentine, it will be necessary to install a casing in the hole. The least expensive casing that will not deteriorate within the life required should be used. Plastic pipe or black iron pipe are commonly used. In soft rock, it may be necessary to drill with a casing to prevent the col-

Jan 1, 1971

"Chairman: Prof A. E. H. BLEKSLEY Rapporteur: Prof J. ELBRONDPanel Members: Prof J. C. Griffiths, Prof T. E. Hawkins, Mr A. C. Langton, Mr M. Splaine, Mr A. WeissThe reasons for failure of computer applications in the mineral industry and the direction of future developments.The Chairman opened the discussion by elaborating on the disappointment felt by some authorities with the lack of progress in the application of computers in the mineral industry during the last ten years, and posed the question to the panel : 'Do you agree that the computer age has not come up to expectations?'Mr Langton said that although there seemed to be a tremendous amount of brainpower applied to the theoretical side, he thought that the production men had not got all the help from computers that could have been given to them. The computer, said Prof Griffiths, is as yet a new tool which should not be used to do old things in old ways. To learn to use the computer will take time. After all, he said, it had taken 400 years after the introduction of the printing press to achieve general literacy, and perhaps it will take 40 years after the introduction of the computer to achieve `numeracy'.In Mr Weiss' view, the reason for the feeling of disappoint¬ment lay in the focussing of attention on the computer. The blame, if any, lay with the people surrounding the computer, that is, the analysts and programmers, to whom the emphasis should be shifted.Prof Hawkins said that he thought that some applications of the computer in the mineral industry had been successful, such as, for example, the compilation of payrolls. Reasons for failures in other areas were to be sought in the fact that the people connected with computers had failed to realise that they were merely part of a system. They had not understood the power structure of the organization which their work tended to change, and were therefore not prepared for the inevitable conflict with the production men.In Mr Splaine's view the production man had not received the assistance he could have had from the computer people because he may possibly not have allowed this to happen.Prof Bleksley concluded from these opinions that the promise which computers had ton years ago had not been fulfilled and added that the opinions expressed by the panel had intruded on his next question which was: 'Is the reason for this that people are involved?Prof Hawkins elaborated on his previous theme, namely, that of computer people in relation to management. Com-puter people, he said, were trying to impose change on management but were not prepared to share the responsibility for these changes. In fact, they wanted their work to be distinct and separate, and, as far as management was concerned, changes would be made when management believed that these would be less agonizing than no change at all."

Jan 1, 2014

During the presentation of the papers, questions were deferred until after the last paper in the afternoon. At that time, the authors and co-chairmen formed a panel for discussion of any pertinent questions. The panel was as follows: Carl Gerity - Ozark Lead Company – Chairman Mike Young - Master Mechanic - Ozark Lead Company Largo Albert - Maintenance Specialist (hoisting) Mines Maintenance Dept. - International Nickel Company, with assistance from Co-author Alan Cameron - International Nickel Company Gary Beerkircher - Product Manager - Rexnord Inc., Nordberg Machinery Group Richard Schaal - Director of Maintenance - Superior Division, Magma Copper Company Rich Hodgson - Assistant Production Superintendent - FMC Corporation The remarks have been edited by the panelists for readability, the basic ideas were not changed. Additional thoughts by the panelists submitted at the time of their revision are indicated by ***.

Jan 1, 1975

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By D. Piper, J. Noble, M. Richardson, J. Wojcik, L. W. Cope

L. Cope Welcome. I am pleased to see so many people interested enough to stay until this last session of the last afternoon of the convention. Of the people on the panel here, everyone has done everything in placer mining, but we have tried to sectionalize it with each one of us taking a particular portion. Any one of us could probably answer any question. I am very pleased to see some well experienced people in the audience. To start the discussion, Joe, can you give us a brief comparison of pit and drill sampling? J. Wojcik They both have their place. If you expect your deposit is something that is going to have widespread fairly uniform grades, then the pits may be the way to go. If you are going to have something you have to trace for several miles down the river valley, you can't do it with pits and do a proper sampling job. C. McLain Joe, the end result of all of this is to go ahead and mine it if it is a deposit. Do you try to relate your drilling results to something in mining itself against the recovery, because the drilling in different types of ground will give you different kinds of recoveries, and mining in the end is what you are going to do? Do you try to relate this to your mining method?

Jan 1, 1992

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

By D. A. Livingstone

"INTRODUCTORY REMARKS BY PANEL CHAIRMAN - D. A. LIVINGSTONEThe mining industry has progressed significantly from the dusty mines and mills of decades past to the modern processing complexes of today, and improved technology has made great strides in eliminating debilitating lung discuss. More recently, the public's environmental awareness is also working to enforce more stringent regulations and controls in tl1e matter of dust in working places.There are numerous excellent texts and handbooks outlining the principles of collection of dust produced in the various unit operations entailed in the crushing, screening and the transport of ore. However, it is painfully obvious that dust emanating from belt return idlers and scrapers, take-up pulleys, skirting, larger and deeper chutes, clean-up operations, etc., which I choose to refer to as fugitive dust, presents some seemingly unmanageable difficulties, or at least difficulties inordinately costly to correct. Possibly static electricity is adding to the difficulties. In my view, these problems are magnified in many of our B. C. operations where ore from open pit mines in cold climates is frequently crushed in unheated buildings, thereby precluding the simple and obvious use of water sprays for dust suppression.It is hoped that the presentations and discussion which follow will emphasize some of these unusual problerr.s and suggest corrective measures, either tried or planned."

Jan 1, 1976

By Stanley Bunk

The fluidized bed was invented by Fritz Winkler of Germany in 1921. The first application in the U.S. was in the development of the fluidized bed catalytic cracking of petroleum in 1942. Today, fluid bed cracking reactors are an integral part of every oil refinery. When fluid bed technology was first considered for applications outside the petroleum industry it was recognized to have uniform temperature, close control of the gaseous atmosphere and excellent mixing between solids and gases. Roasting of sulfide ores and concentrates was an obvious match. The first application was a single stage roaster for gold refining in 1947. There have been over four hundred commercial fluid bed roasters built and operated successfully in the four decades since the fluid bed was invented. There are three general categories of roasting applications. The largest number of roasters fall into the dead roasting category which includes gold ore roasters. The other categories are sulfating roasters and partial roasters (Reference 1).

Jan 1, 1990

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By C. Overton, R. W. Nice

"With todays economic trials and tribulations we have all become deeply engaged in costs and cost cutting in our field of mineral processing. Grinding is one of the most expensive unit operations. The cost of grinding media is the most expensive item in grinding costs. Therefore, it is only reasonable to attack the cost-cutting area by trying to reduce the consumption of media. This introduces the field of autogenous or rock-on-rock grinding.Rock-on-rock grinding is not new to us. It has been known for many decades;The South Africans used pebble grinding in the '20's for gold.Mr. B. Crocker was prompted for the same reasons to introduce pebble grinding at Lakeshore Mines in Kirkland Lake during the last war.The Buffalo Anchorite used beach pebbles in grinding prior to the war.Autogenous and semi-autogenous grinding is used quite successfully in the iron ore field. Base metals have their examples in Australia at Caba, in Africa at Komato and in Sweden at Aitik.Recently three mills in British Columbia and one in Arizona started with autogenous mills in their circuits. One was originally conceived to utilize a modified autogenous grind with a crusher in the circuit. All except the same mill had contingency plans for converting to semi-autogenous. All four mills have since converted to the semi-autogenous mode. These are Island Copper, Lornex, and Similkameen in B.C. and Pima Mining in Arizona."

Jan 1, 1975