Search Documents

By N. O. Johnson, R. A. Westin

Polychlorinated biphenyls were the basis of non-flammable askarel dielectric liquids wed in electrical equipment made between 1929 and 1978. Although PCBs were widely used in mine electrical equipment, the toxicity and environmental persistence of this chemical led Congress to ban its manufacture and use. Bureau of Mines Information Circular 8838 summarizes the regulations imposed by the EPA on the use and disposal of PCBs, and describes the limitations of available substitutes. Recent changes in the regulations will impose additional requirements on the use of PCBs by the mining industry. This paper is an update of the material presented in the Bureau of Mines information circular.

Jan 1, 1983

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By R. J. Mirville

Flocculation is an important step in the treatment of coal preparation waste waters. The effects of polymer charge and molecular weight and solution pH and ionic strength on the adsorption and flocculation characteristics of a series of polymeric flocculants on some typical waste water constituents have been studied experimentally. The results indicate that the nature and extent of flocculation are strongly system-dependent. For the case of coal, both adsorption and flocculation behavior can be correlated with the polymer conformation in solution. For the mineral constituents, on the other hand, adsorption and flocculation depend also on the surface properties of the solid.

Jan 1, 1979

By Ian Larkins

The Ruby Hill Mine agglomerates crushed low-grade ore (nominally -1 .5'') with high-grade filtered tailings (filter cake, nominally 80% -65#). Cement is added as a binding agent. The agglomerated ore is then conveyed and stacked on the heap. In 1998 approximately $480 000 was spent on cement for agglomeration. Cement for mill pH control and agglomeration was the largest single reagent cost at Ruby Hill. In an effort to reduce agglomeration costs a test-work program was initiated to investigate alternative binders and optimum binder additions. This paper summarizes the test­work results to-date.

Jan 1, 1999

By Rita C. L. B. Rodrigues, Esperidiana A. B. Moura, Gisele D. Lazo, Renata D. S. Coiado, Rene R. Oliveira

Agricultural residues, which are produced with large quantities annually throughout the world, may be used as reinforcement plastic to replace the wood and produce particleboard for application in the development of low cost construction elements and reduced environmental impact. The main aims of this study was to investigate the effects of agricultural wastes and glass residues addition on the properties of recycled-HDPE/EVA blend for use in particleboard manufacture. The recycled-HDPE/EVA blend reinforced with corncob fiber (15 wt%), coffee parchment (15 wt%) and glass residues (1 wt%) were processed by melt extrusion, using a twin screw extruder and injection molding machine to obtain specimen test samples. The samples were characterized by mechanical test, XRD, TG, DSC, and FE-SEM analysis to understand the nature of interaction between the fillers reinforcement and recycled-HDPE/EVA blend matrix and their properties were discussed.

Mar 1, 2017

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By B. J. Scheiner, D. A. Stanly, P. M. Brown

The Bureau of Mines has developed an equation that describes the dewatering of clay slurries with poly- ethylene oxide. This dewatering equation is: A[ ] = KC + b where n, k, and h are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering, A, is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that the amount of polymer required for dewatering and polymer solution viscosity are both the consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1991

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By Mohammad Kor, David Beattie, Agnieszka Mierczynksa-Vasilev

The selectivity of polymer adsorption in mixed mineral systems is the basis for polymer depression of gangue minerals in flotation. Effective polymer depressants not only reduce gangue mineral recovery, they also have minimal effect on the recovery of the value phase, presumably through targeted adsorption on the gangue phase, and minimal uptake on the value phase. Traditionally, polymer depressant design has been guided by single mineral phase adsorption tests, with affinity and maximum adsorbed amount determined for gangue and value phases separately. However, there is a need to determine the actual extent of adsorption on the gangue phase while in the presence of the value phase. In this work, we report on the development of in situ atomic force microscopy (AFM) imaging for determination of polymer depressant coverage and morphology on mixed mineral surfaces. Our group has previously used AFM imaging on single minerals to connect adsorbed layer characteristics with bubble-particle attachment and flotation outcomes. Two sample types were used to test the methodology: (i) a mixture of two crushed/ground minerals encased in resin; and (ii) a composite mineral sample containing macroscopic regions of three different mineral phases. The samples have been used to probe the selective uptake of two modified dextrin polymers (octenyl succinate anhydride dextrin). AFM images acquired in situ (while all surfaces are immersed in the same polymer solution) of each mineral phase have revealed the natural selectivity of the polymer for the mineral surfaces. In all cases, the polymers adsorb on the all mineral surfaces present, but to a varying extent.

Jan 1, 2014

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By T. J. Dudek

To be competitive in automotive applications, polymer composites must be processable by high production rate processes like injection molding (IM), reaction injection molding (RIM), structural rim (SRIM) and compression molding. With current fiber reinforced composite materials, performance properties are sometimes compromised to make them compatible with these processes. This is done by decreasing the amount and length of the reinforcing fiber and the viscosity and molecular weight of the polymer matrix. Sheet molding composite (SMC) and thermoplastic polymer blends are examples of polymer composites which are cost effective in many applications and meet the high speed processing requirements for automotive parts.

Jan 1, 1993

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Alex Joseph

A tertiary amine containing polyamine in its back bone was grafted to exfoliated graphite oxide by means of a series of chemical reactions.The synthesized amine functionalized polyaniline grafted to exfoliated graphite oxide (EGAMPANI) was characterized using various techniques such as, FTIR, TGA, Raman, and X-Ray diffraction.The synthesized EGAMPANI was blended with carbon paste electrode, and used to study the response of Hg2+ in acetate buffer solution.Preliminary analysis showed that the anodic current intensity using the EGAMPANI modified electrode was higher during a potential sweep and 10-4 M concentration of mercury could be detected which could be improved to 10-6 M using anodic stripping voltammetric technique. Keywords: metal sensor, exfoliated graphite oxide, functionalization, polyaniline

Sep 1, 2012

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By Robert P. Mahoney, William J. Roe

Polymers of a wide variety of composition are used in coal and mineral beneficiation. Applications include flocculation and coagulation in thickeners, filtration enhancement, mill scale control, dust control, ore leaching improvement, and pond management. The proper chemistry of the polymer is determined by many factors, including the nature of the process, mineral type, and respective performance requirements. This paper provides an overview of the various current applications of polymers in mineral processing, and a description of the applicable polymer chemistries which find utility in these applications. Examples of structure/performance relationships are discussed.

Jan 1, 1994