Search Documents

By E. M. Stiles

Introduction The papers that follow deal with recently completed major improvements in practices at the Sullivan operations in Kimberley. The papers have been prepared by members of the Consolidated Engineering Staff and outline the construction programme which has been in progress for the past three years, entailing an expenditure of some millions of dollars. Four major operational changes have been brought about in the mine and concentrator. They are: (1) A change in backfill procedure for filling stopes below the 3900 level. (2) A 12,000-ton,per-day sink-float plant at the concentrator. (3) A new haulage system from the mine to the concentrator. (4) A completely new crushing plant and ore storage facilities located underground. A brief outline of the background and history leading up to this overall project will be given to show how each started as an independent betterment and how they were finally co-ordinated into one major programme. The first of these, namely, the necessity for backfilling stopes below the 3900 level, was the most pressing problem. All filling to date bad been done above the 3900 level, where mining was carried on in an irregular pattern of open stoping. Stopes below the 3900 level were first opened in 1940 and are being worked on a regular pattern of panel sub-level open diamond drill stopes. The two areas are separated by a sill pillar traversing the entire length of the vein at the 3900 level elevation.

Jan 1, 1950

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By A. L. Holley

THE members of the society are doubtless aware that the production of American Bessemer steel works is constantly increasing ; that the same converters and machinery are doing more work every year. This enlarged output is due to various causes, chiefly the following: 1st. Better organization-better knowledge on the part of both managers and men, of the plant and the process ; of the way to economize the more exhausting labor, and of the arrangement of the details of labor and operations so that they shall not conflict; also, more pluck-a greater willingness to take risks, or, more properly, such an intimate knowledge of the nature and capacities of the refractory tory linings in various stages of disrepair, and the probable be- . havior of the fluid metal at various stages of its treatment, that the precise nature of the risk may be better known, so that the works may be crowded to their full capacity. In the early practice, after getting four or five consecutive heats in a day, the men preferred to "let well enough alone," and to devote the remaining time to preparation for another turn. Now, thirty, and sometimes forty heats are regularly made during the twenty-four hours, day after day, without the frequent occurrence and without the fear of breakdowns or "messes," as the spilling of steel charges was graphically named in Sheffield. 2d. Although no new refractory materials have been developed, improved means of preparing such as we have, and of imbedding

Jan 1, 1874

By John A. E. M. Church

THE prospector's pan was the first implement used for saving gold, and its action is so effective that it has never been equalled for thorough work. Copper plates, blankets, sluices, and amalgamators of several patented designs have thrust it aside, but in spite of all the advances made there is no dispute among experienced men as to the comparative thoroughness of the work done by it and its rivals. When its rivals are doing their best, the pan can take their discarded refuse and prove their inefficiency by producing from it not only gold, but even the mercury which has been lost from the machines themselves. The trouble with the pan has always been that it was only a tool. Man was the machine that moved it. His work was high-priced, the quantity treated small, and it was impossible to use the pan for any but the richest sands. As a consequence the best gold-saving appliance known has been discarded for years and replaced by machines of inferior excellence, but which could more than make up for their limited ability in saving gold by their capacity for treating great quantities of ore. Mr. Peck is one of the old-time amalgamators of the Comstock district, and the first idea of the new machine came to him as he used to pan below the tailrace of his mill. No matter how fine the work of the mill was, the pan invariably proved that better could be done. The tailings always contained gold, silver, and mercury. This state of things is just as true to-day, after all the improvements that have been made, as it was then, and the much-vaunted method of the " Washoe process" consists in extracting 72 per cent. of the gold and silver by one operation, and then repeating this operation half a dozen times to get out about one-third of the remainder. With all the advances of twenty years in milling, there is nothing more crude in metallurgy than the treatment of tailings in many of the large mills of the West.

Jan 1, 1880

By William P. Blake

THE use of diamonds upon a large scale in drilling rocks, and the substitution to a certain degree of rotary diamond drills for the ordinary steel percussion drills, marks a new era in the art of mining. Since the invention by Leschot of the diamond drill, it has steadily advanced in its utility and range of application, and in the appreciation of miners and engineers. It must be claimed as one of the many gifts of science to the arts ; and it is, in particular, one of the fruits of the scientific education given at the Ecole Centrale, at Paris. Members are all, doubtless, more or less familiar with the construction of the drill and of the machinery by which it is applied in boring. It is, therefore, my present purpose only to direct your attention to some recent marked improvements, made by the American Diamond Drill Company, by which the economy and efficiency of the machines have been increased. Form of Bit. The annular or ring form of the drill-head or bit was, I believe, the earliest; and it is still in use, without essential modification, wherever it is desired to obtain a sample "core" or specimen of the rock traversed. But for mere drilling, regardless of the preservation of a test-core, a solid-head bit is preferred, except for very large holes. Until recently, these solid-head bits were made with a pointed cutting face shaped like an obtuse cone. This form was assumed to be the best, being most in accordance with the experience obtained with percussion drills. It is found, however, that the exact reverse

Jan 1, 1873

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By William J. Kohan

Milling has traditionally been considered more art than science. In the last 10 years, significant improvements in process equipment have been made and we are finally taking significant steps toward approaching grinding as a science. Two machines have been at the center of this development. These are the roll press and the high efficiency separator. The former can be considered as a new technology or adaptation of existing i.e. roller mill. The latter is clearly an improvement of existing technology. Other machines have been introduced to a lesser degree and later. Among these are the CKP and Horomill. The purpose of this paper is to provide an over- view of the currently available modifications for operating systems and options for new milling circuits with some comments on their application and history.

Jan 1, 1997

By W. A. Gow

"In January of 1964, a group known as the Canadian Gold Metallurgists was formed with the backing of the managers of most Canadian gold mining operations. This organization is composed of about thirty mill superintendents of Canadian gold milling operations where the cyanidation process is in use, and one member from the staff of the Mines Branch, Department of Energy, Mines and Re-sources, Ottawa. The aim of this group is to bring together gold mill operators, and research and development people from both industry and government for the purpose of discus-sing common metallurgical problems, and deciding on what operational R and D efforts can be made to help solve these problems. Since the conception of this organization, this approach taken by the gold industry to the study of metallurgical problems has resulted in benefits to all operators, both by assisting them with problems peculiar to their own individual operations and by providing developments of general interest to the industry.This paper describes events leading up to the formation of the Canadian Gold Metallurgists, and how the group has operated since its formation. Examples of progress made toward the group's objectives are given, and possible future programs are discussed."

Jan 1, 1968

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By Arthur Anderson

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Inno-vations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these fea-tures that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort. was made to use heavy truck haulage in the trans-portation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the seasor1 of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By R. P. Brown

To gain some idea of the progress recently made in the measurement of high temperatures, we must review the temperature-measuring devices of the past. As far back as 1782, Wedgewood, a famous potter in England, attempted to measure his, kiln temperatures by means of clay trials, or test pieces, that indicated the expansion or contraction that occurred with certain changes in temperature. He also produced cones off clay, formed of various mixes, to form a whole series for the range of temperature met with, in firing clay products. These cones are still extensively used to measure kiln temperatures in the pottery industry. Cones are affected not only by time but by temperature and the rate, of firing, consequently, they are not an accurate measure of temperature. In addition it has been common practice for years to attempt to measure temperatures with fusible salts. Capsules of these are inserted in the furnace and indicate, by melting; when a certain temperature, has been attained. While' such salts cannot be considered a precision form of temperature-measuring device, they have proved reasonably accurate in checking temperature.

Jan 9, 1919

E. D. TILLYER,* Southbridge, Mass. (written discussion?).-It is quite generally known that there is very little that is standard about a mercurial thermometer at temperatures above 212° F. (100° C.) because so many precautions must be taken-precautions that are rarely realized in practice-such as depth of immersion, aging, elastic fatigue, separation of mercury column, and accidental deformation from very slight excess temperature. One cannot help wishing that Mr. Brown would dwell at greater length on the practical side of both radiation and optical pyrometey, both of which have great possibilities as commercial instruments. In the radiation pyrometer we have ideal conditions for a permanent instru-ment, no materials being exposed to excessive temperatures or subjected to contamination from the furnace fumes which may raise such havoc with an ordinary pyrometer. The development of a radiation pyrometer requires a thermocouple having a relatively high electromotive force but which need stand temperatures of only 200° F. or 300° F. instead of 1500 to 2000° F., which is required of even a base-metal couple. The galva-nometer, if located near the thermocouple, does not need to have a high resistance as at such low temperatures no changes can occur in the thermocouple that will affect its resistance and, consequently, the in-dicated temperature.

Jan 11, 1919

A. 0. ASHMAN, Palmerton, Pa. (written discussion *).-From a theo¬retical point of view the best method to maintain the cold junction at a constant temperature is by means of a pipe driven in the ground, to which the so-called cold-junction compensating leads are run, ;and of course there are many times and places where it can be successfully used. There are, however, several objections to this method. In the vicinity of any furnace there are apt to be underground flues for preheated air or gases, recuperators, water mains, etc., which will eliminate the probability of a constant temperature. These, of course, can be avoided by carrying the leads to distant locations known to be free, but this is not good practice because the so-called compensating leads have a rather high re¬sistance, which materially affects the accuracy of even the high resistance instruments, unless they are specially calibrated for it. Moreover, the cost of these long leads is almost prohibitive. A better way is to run short lengths of compensating leads to electrically heated constant¬ temperature boxes conveniently located near the furnace in a place that is of fairly uniform temperature. These boxes are on the market and can be procured at a cost that is approximately equal to the cost of 100 ft. of compensating leads. They can be connected to any power or lighting circuit and once set require very little care. One box will ac¬commodate a number of couples.

Jan 12, 1919

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By E. O. Stensholt

The Hybinette electrorefining process for production of cathode nickel was in use at Falconbridge Nikkelverk A/S, Norway, until 1975 when conversion to the new chlorine leach process was started. In 1978 the conversion to electrowinning had been completed, but further major improvements to the process have been made up to 1987. After a major expansion program in 1985 - 87 the refinery has a nickel capacity of 54 000 mt Ni/year. The main feed materials to the process are converter matte from the Falconbridge smelter in Sudbury, Ontario, Canada, and from the BCL smelter in Selebi-Phikwe, Botswana. A typical composition of the mixed feed to the refinery is: 40 - 45% Ni, 25 - 30% Cu, 20 - 22% S, 2 - 3% Fe and 1.0 - 1.5% Co. The matte is chlorine-leached in the first process step, nickel being dissolved selectively in a train of leach-cementation tanks. Essentially all copper and sulphur that was present in matte appears in the leach residue as CuS. In 1986 an autoclave treatment stage was added to the process to improve nickel extraction from the leach residue. The resulting strong nickel chloride solution is purified by the process steps (1) precipitation of iron and arsenic, (2) solvent extraction of cobalt and other minor elements and (3) precipitation of lead and the remaining impurities. The nickel solution is then fed to the tankhouse, where various nickel products are produced by electrowinning. The chlorine gas that is produced during the electrolysis is returned directly to the chlorine leaching tanks to dissolve more matte. After stripping from the loaded organic phase and solution purification cobalt is also produced by electrowinning. The copper sulphide leach residue, which contains some nickel, is dead- roasted in fluidized-bed roasters. The sulphur is recovered and sold as sulphuric acid. The calcine is leached in spent copper electrolyte, from which cathode copper is produced by electrowinning. Precious metals and the remaining base metals are recovered from the copper leach residue. The Falconbridge chlorine process is very versatile. It can accept a wide range of impurities in the feed and still produce metals of exceptional purity.

Jan 1, 1988

By J. Talja

Keywords: drying, steam drying, concentrates, copper, lead During the past twenty years steam drying has become a prominent technology for drying of non-ferrous metals concentrate. This is mainly because of its low energy consumption and very low emissions. The first applications of significant capacity were stationary steam dryers, which however, faced severe challenges in maintenance costs and availability. That technology was soon replaced by Kumera?s rotary steam drying technology, which has been the dominant technology in new dryer installations world-wide for the past ten years, ever since the first installation in Hamburg in 1999. There are ten Kumera steam dryers in operation today and five more to be commissioned during 2011. Practically every dryer is different owing to continuous development, new innovations and operational experience with continuous feedback from the operators. Most significant improvements relate to capacity increase with the Kumera steam-dryer family, new feeder systems at the wet end, a completely new design of the dry material discharge with increased availability, heating element design and material selection, and control systems. This paper discusses the modifications and improvements introduced which have enabled the Kumera steam dryer to become the global leader in new dryer installations.

Jan 1, 2011