Search Documents

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By N. Hiroyoshi

In the leaching of chalcopyrite with sulfuric acid solutions, the copper extraction rate reaches a maximum at a given redox potential. This article reviews our studies on the determination of the optimum redox potential for chalcopyrite leaching. Shaking flask and column leaching experiments for a chalcopyrite concentrate were performed under various conditions, and the results were analyzed using a normalized redox potential defined from a reaction model assuming the formation of an intermediate CU2S from chalcopyrite. Factors, such as metal ion concentrations, solid/liquid ratio, and presence of iron-oxidizing bacteria, caused significant variations in the copper extraction versus time plots. However the copper extraction rate versus normalized redox potential plots were independent of the above factors and the copper extraction rate reached a maximum at the normalized redox potentials around 0.43. Converting the normalized redox potential to the solution redox potential gives the optimum redox potential for chalcopyrite leaching as a function of cupric and ferrous ion concentrations. This semi-empirical equation can be used to predict the optimum redox potential during leaching operation, and is useful to design the redox-controlled heap leaching for chalcopyrite.

Jan 1, 2007

By V. G. Papangelakis, I. Guzman, S. J. Thorpe

Pressure oxidation (POX) leaching has been commercially applied to refractory gold ores since the 1980s. In the process, sulphide material is oxidized and dissolved in order to release the gold encapsulated in the sulphide matrix, making the gold available for further recovery. Redox potential is a significant parameter during POX, however it is only measured ex-situ at atmospheric conditions. In-situ redox potential measurement would provide instant information that allowing adjusting the process parameters accordingly. In the present study, redox potential measurements were performed during POX of sulphide material at high temperatures and high pressures. The working electrode was an Ir electrode combined with a flow-through reference electrode in a novel and robust configuration. Experiments were performed in a 2 L titanium autoclave, at 200–220°C, 50–110 psi oxygen overpressure, and 10–30% solids mass fraction. Temperature and oxygen pressure conditions were selected in order to reflect POX of refractory gold ores. Results show that the Ir electrode is consistent with theory and is able to perform well under these conditions, showing promise as a new in-situ sensor.

Jan 1, 2017

By Thomas M. Goodell, Timothy D. Arnold

Dilute-phase pneumatic conveying has been used in the mining industry since the 1920s. It has primarily been used for the hoisting of coal and salt ores, and as a transportation medium for backfill material. More recently there have been investigations into a wider variety of applications, which this paper addreses. The paper will point out some deficiencies in the system. It 1s not the "champion" of the mining industry, but rather an excellent srste?1 with a variety of applications that may not have been studied m enough detail. The most imaginative applications to the Redpath Pneumatic Conveying System have been initiated by persons needing an innovative application to a specific predicament.

Jan 1, 1992

By Valeria Romina Stricker

Acerbrag es una empresa Argentina siderúrgica de 50 años de trayectoria, desde el año 2007 pertenece al grupo Votorantim de origen Brasilero. Se dedica a la elaboración de aceros largos para la construcción. La planta industrial cuenta con un proceso de acería integrado, horno eléctrico, horno cuchara y máquina de colada continua. La materia prima es 100% chatarra, característica que la diferencia del resto de las acerías del país. Debido a esto el enfoque principal de este proyecto es reducir el costo de fabricación mediante un “empobrecimiento” de la carga metálica a partir de la flexibilización de los límites de especificación. Esto implica un mayor control del desempeño de los procesos a fin de detectar posibles desvíos, para ello fue necesario implementar la utilización de herramientas estadísticas y gráficas para su monitoreo. La modificación en el mix de fabricación no muestra una alteración significativa en la composición química y propiedades mecánicas de los productos terminados, situación favorable para la continuidad del proyecto. Se observa además, de la reducción de costo esperada, una ventaja en la operación del patio de chatarra y el proceso de acería y en la utilización de chatarras con altos niveles de residuales tales como Cr – Ni.

Aug 16, 2017

By Iván Arana Sevallos

Dado que la mina Catalina Huancca posee rocas malas dentro de sus labores mineras, surge la inestabilidad de las mismas. En ese sentido, el presente texto señala la forma de aplicar la voladura controlada a través del uso de espaciadores inertes para espaciar los cartuchos de explosivo y reducir la presión que ejerce el explosivo en el taladro al momento de la explosión.

Dec 1, 2014

By Malcolm Flavel

Dado que la trituración constituye el componente de alto costo en la mayoría de procesos mineros, se utiliza una tecnología basada en el resultado de los programas de investigación desarrollados por Allis-Chalmers Corporation. donde se busca reducir paulatinamente dichos costos. En ese sentido, el presente texto señala cómo reducir el consumo de energía requerida por el proceso de trituración y así minimizar la inversión de capital necesaria para construir las instalaciones del procesamiento.

Mar 1, 1983

By Ronald Mamani, Russel Allidren, Diego Llanchipa

Esta investigación tuvo como objetivo evaluar la eficiencia del Sistema Tohá —conocido como Lombrifiltro o Biofiltro Dinámico y Aeróbico— para el mejoramiento de la calidad de aguas residuales domésticas. Para evaluar los parámetros DBO5 y DQO se tomaron como puntos de referencia aspectos biológicos del agua a tratar, que pasó a través de un biofiltro compuesto de 4 estratos (aserrín, grava, arena y carbón), el primero de los cuales incluyó lombrices rojas (Eissenia Foetida). Antes y después de realizar el filtrado se realizaron análisis de laboratorio. Como resultado respecto de remoción de contaminantes, se obtuvieron cifras que implicaban reducciones superiores al 50%.

Aug 31, 2019

By D. A. Sutch

En 1958 se instalaron dos hornos Tysland-Hole en la planta Siderúrgica de Chimbote, construído por Elektrokmisk A.S, cuya sede social se encuentra en Oslo, Noruega. En ese sentido, el presente texto describe el funcionamiento de dichas hornos para la reducción de minerales de fierro en Chimbote. Para el revestimiento del horno se emplean materiales aislantes diversos y tres tipos de mezclas refractarias que se colocan mediante apisonado. Asimismo, estas mezclas retractarias son apisonadas contra moldes metálicos que permanecen "insitu", es decir, que reciben la primera carga del horno.

Sep 1, 1963

By Renan Barrio de Mendoza

"El presente texto señala la aplicación de nuevas tecnologías conceptos para reducir u optimizar el consumo de energía, como los costos de operación en los procesos metalúrgicos. Así, el uso eficiente de la energía en la actividad minera tiene su impacto en la sociedad -en tanto se emplee adecuadamente en las etapas del tratamiento del mineral. Cabe recordar que en las operaciones de reducción de tamaño de partículas es más barato volar que chancar, así como chancar que moler."

Jul 1, 2015

By Javier Casas, Richard Corsino, Miguel Baylon, Miguel González

El presente trabajo consistirá en presentar la metodología realizada para la inyección de cianuro a presión en el pad 1A, la cual contempla la realización de estudios de las condiciones del pad, barrenación de los pozos de inyección y de monitoreo, realización de pruebas metalúrgicas, inyección de cianuro a presión, monitoreo geotécnico en la inyección, y finalmente los enjuagues realizados. Finalmente se presentarán los resultados obtenidos de las onzas de oro y plata recuperadas de esta prueba piloto y los planes futuros que se tienen acerca de estos trabajos.

Sep 30, 2022

By Leoncio H. Lizárraga

"El método de reducción empleado en la mina Casapalca de la Cerro de Pasco Corporation, situado en la provincia de Huarochirí, Lima, es el más conocido universalmente, dado que el mineral derribado por la explosión desarrolla una doble función: sirve como piso de trabajo de los perforistas y como relleno provisional para soportar las cajas de la veta. En este punto, el objeto del trabajo es describir las distintas etapas del método actual en comparación con las del sistema antiguo. Es menester recordar que dicho sistema se usa en zonas donde la silificación de la caja ha sido intensa, es decir, que el relleno de los filones es lo suficientemente fuerte para soportarse a sí mismo. Ya, en la etapa de desarrollo, la preparación de tajeos se da cuando cuando las galerías y chimeneas se encuentran abiertos a fines de reconocimiento y tener un mejor acceso a los tajeos. En cuanto a las etapas del sistema de producción, si anteriormente el tajeo se iniciaba en los extremos del panel, a través de las chimeneas de acceso, ahora los gradines se inician del extremo en que la chimenea queda con un corte de cuñá a unos pies del extremo para no malograr el camino de escaleras, luego se perfora a uno y otro lado de este corte para formar el primer gradin. Se procede de la misma manera para forrar seis o siete gradines en toda la extensión del tajeo. Por último, en el costo de explotación por reducción, si se usa el método de corte y relleno en las zonas donde se utiliza el de reducción, el costo del primero sería más alto que el último."

Jul 20, 1955

By R. Oler

The mining industry?s traditional preference for protective coatings in corrosive environments, due to cost considerations, has been to apply galvanized and epoxy coatings. As a result of extreme pH levels and the limitations of current products, a new coating has been developed to withstand severe conditions. Harsh chemicals and corrosive groundwater pose added challenges to mines in maintaining long term ground support which demands continuous rehabilitation. This paper highlights the challenges and identifies a solution by applying a new economic coating to DSI?s Omega Bolt? that withstands the most corrosive of conditions. [ ]

Jan 1, 2012

A recent study estimates that a 10% improvement in the performance of wire rope used on draglines could save the US coal industry $2 million annually in rope costs. In addition, such an improvement could boost annual coal production by allowing the industry's draglines to remove an extra 1.5 million m3 (2 million cu yd) of solid overburden each year. These findings, although admittedly preliminary, suggest the magnitude of benefits that can be derived from a well-planned wire rope maintenance program.

Jan 3, 1978

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By Henry Chumienski

Next to the paper industry, the steel industry is a major user of water. Without an adequate and reliable source of “good” water, steel cannot be produced. The use of water has a direct impact on steel quality and on our environment. Used improperly, water can also add unnecessary costs. Used properly, water can maintain and improve steel quality, enhance our environment and control or reduce the “total cost of operation”. Water needs to be more than just “wet and not lumpy”. Water quality needs to be based on the end use. This paper discusses ways to manage many of the water systems. With little or no capital investment it is possible to develop operating practices that protect your initial investment, ensure that the water systems do not have a negative impact on quality or your production costs and also minimize your chance of having an environmental incident.

Jul 30, 2018

Presentation Agenda ?Background ?OEM Recommendations before RCM ?Operating Context ?OEM Recommendations after RCM ?Reality of Failure ?RCM Deliverables ?Maintenance program optimization ?Spare part optimization ?Implementation ?Further Considerations -Three scenarios ?Summary and Conclusion Background ?P&H Mining?s LCM division performed a RCM study on a ?generic 4100 XPB shovel?in Milwaukee. ?P&H soon realized that the analysis required context -The recommendations were manufacturer knowledge based. -The outcome based on manufacturer requirements. -The strategy was not applicable to all machines, etc. Operator experience and ?local knowledge? are key to the success of an RCM analysis. P&H approached Teck Coal?s Fording River Operation to assist with ?Operating Context?. Teck provided operator and maintainer experience.

May 1, 2010

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017