Search Documents

By E. A. Sondreal, F. I. Honea

This paper summarizes coal and ash properties and pilot-plant results for 14 key lignite seams in the Gulf Province, as well as discusses operating problems encountered by the four Texas power plants burning Gulf Province lignite. Some consideration is given to the design of future power plants.

Jan 1, 1982

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world's notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world's great mines.

Jan 1, 1981

By Dan Ifrim, Andre Solecki

Tunneling could be a major challenge to tunneling contractors as tunneling operations can be seriously affected by the Tunnel Boring Machine (TBM) performance. Specifying the appropriate TBM methodology, selection of systems and features, is critical for managing tunnel risks and contribute to successful tunneling project. The paper analyzes tunneling records from the recently completed City of Toronto’s Ashbridges Bay Treatment Outfall tunnel project and underlines the righteous selection of the TBM type and associated TBM systems in achieving good advance rates during tunnelling and managing project risks. The paper intends to draw attention of a few aspects of TBM technical specification importance and highlight the lessons learned from this process.

Jun 13, 2023

By A M. Sherwood

The Otago and Southland lignite deposits represent by far the largest known fossil energy resources in New Zealand. Despite their size they have remained virtually untouched since exploration in the 1970s and 1980s defined their extent. In total there is an estimated 10.9 billion tonnes of lignite in 13 defined fields in Otago and Southland. Much of the exploration work only targeted seams at shallow depth and it is highly probable that there are further resources at depth in the fields that have been explored to date.   L&M Lignite Limited (L&M) holds exploration permits over a number of lignite deposits and is currently engaged in pre-feasibility studies to investigate the potential of the lignites for gasification. L&M is focussing its studies on the Hawkdun and Ashers-Waituna deposits. Coal quality in these deposits, particularly Ashers-Waituna, is highly suitable for gasification. In total the two deposits contain 1647 Mt of potentially recoverable lignite. L&M has engaged a variety of consultants to progress this project. The Hawkdun and Ashers-Waituna deposit databases have been re-evaluated and the resources remodelled. Further drilling has been carried out and the coal quality database has been expanded. The baseline project is to develop a mine to feed a plant that will produce liquids, specifically low-sulphur diesel and naptha, using the Fischer-Tropsch process. The project anticipates a staged development of 10 000 barrel per day units, each requiring mining at the rate of 12 700 tonnes of lignite per day. The production of other products including ammonia-urea, methanol, hydrogen and electric power is also under study.

Jan 1, 2005

By C. H. Stein

THE Pennsylvania Legislature, on March 13, 1837, passed an act authorizing the Lehigh Coal & Navigation Co. to construct a railway to connect the North Branch Division of the Pennsylvania Canal with the slack water navigation f the Lehigh River; the navigation company accepted this act on May 10, 1837. Edwin A. Douglas, chief engineer for the navigation company, located the route for this railway from White Haven to Wilkes-Barre, which was called the Lehigh & Susquehanna Railroad. The object was to transport coal from the Wyoming Valley, of Pennsylvania, to the Atlantic seaboard. This railway was considered a marvelous piece of engineering, as it included a tunnel nearly 13 mi. long, and a series of inclines, or planes, up which the cars laden with coal were raised from the vicinity of Ashley to the summit f the mountain near Solomon's Gap, whence they were taken to White Haven by rail. There the coal was transferred to canal boats. In June, 1862, floods almost completely destroyed the upper division of the canal, so on March 4, 1863, the Pennsylvania Legislature passed an act prohibiting its restoration, but granted a charter for the construction of a railway from White Haven to Mauch Chunk to connect with the line from White Haven to Wilkes-Barre, previously built. On March 16, 1864, a supplementary act was passed extending the Lehigh & Susquehanna Railroad to Easton, Pa. This completed a direct all-rail route from Wilkes-Barre to the New York harbor (by way of the Central Railroad of New Jersey). Up to this time, all freight and passenger traffic passed over the planes, but in 1866 and 1867 there was constructed what was known as the "back track" down the mountain side between Solomon's Gap and Ashley over which all the passenger traffic and empty cars thereafter passed; it is now known as part of the main line. For the handling of the heavy coal traffic, however, this would have involved a continuous climb from Ashley, 170.27 mi., from New York, to Solomon's Gap, 157.8 mi. from New York, or a distance of 12.47 mi., and a total ascent of 1,013.75

Jan 9, 1921

By Pedro Tumialán

Los yacimientos mineralizados metálicos de la cordillera de Huayhuash se hallan en rocas estratificadas del cretácico medio, discordantes y algunas veces concordantes con la estratificación en rocas ígneas del terciario. En ese sentido, el presente texto describe el estudio de esta asociación mineralógica a través de la división de tres áreas: zona de Pacllón (sur), zona de Huallanca (central este y norte), zona de Tucu Chira (central oeste); en una extensión total de 60 por 45 Km. Asimismo, los minerales económicos se hallan con otros no económicos, deduciendo una serie de guias mineralógicas para la exploración minera.

Sep 1, 1976

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By José Murilo Mourão

A pelotização de minério de ferro hematítico demanda grande quantidade de calor para a produção de pelotas de boa qualidade. Avalia-se, neste trabalho, a quantidade teórica de calor, necessária para a queima de três tipos característicos de pelotas, e destacam-se pontos importantes do processamento de queima nos fornos de pelotização, no sentido de otimizar o consumo de calor..

Oct 30, 2017

By David Córdova R.

Dado que el método de minado empleado por la compañía Perúbar en la mina Juanita generaba ciertos riesgos de inestabilidad y dificultades operacionales, se propuso un nuevo método de explotación de minado: el de corte y relleno mecanizado por subniveles, cuyo sistema está clasificado como un método de explotación especial y de alta recuperación del yacimiento. En este sentido, el presente texto describe los beneficios de este nuevo método -en tanto ofrece una resistencia de relleno cementado en la masa rocante, así como la estabilidad de los materiales en el relleno hidráulico de los tajeos secundarios.

Aug 26, 1988

By Donald Carlisle

El presente texto revisa los costos, utilidades, cantidades y velocidades de "recuperación" en el empleo de la mena. La mena debe ser explotaba con beneficio -en tanto se trabajan las minas para obtener de ellas un beneficio. Cuando un geológo trata de aplicar la definición citada a una situación concreta, ya no hay simplicidad. Para ello, es necesario explicar cómo se fija la ley marginal, la máxima profundidad de minado, la recuperación porcentual óptima y otros márgenes similares cuando no hay procedimientos rutinarios establecidos. Sobre esta base se calcula la utilidad diaria, tonelada, o total del yacirniento y si este implica una ganancia mínima o no.

Mar 1, 1959

By Donald Carlisle

El presente texto describe las relaciones entre costos, utilidad, cantidades y velocidades de "recuperación" de la mena, así como se consideran las leyes marginales y su velocidad de la recuperación en las minas.

Jan 1, 1970

By Robert Koenig

El presente texto describe los aspectos que implican la demanda energética del país. Para ello, se dicta una política de acción conjunta entre el gobierno, los productores de petróleo y los mineros de carbón, con el fin de preparar un plan que permita la suspensión en el más corto plazo del régimen vigente de control de precios para los combustibles derivados del petróleo, procurando que alcancen gradualmente los niveles que rigen en el mercado internacional y a su vez promover un mayor consumo de los combustibles licuefactados derivados del gas natural, los productos de la gasificación de la antracita, y el establecimiento de gasoductos para su transporte.

Mar 1, 1958

By Cyro Takano

A degradação durante o processo de redução de minérios de ferro é bastante conhecida pelos fenômenos de crepitação e inchamento. Em aglomerados a frio, auto-redutores utilizando cimento como aglomerante, há também degradação pela decomposição de hidratos que conferem resistência a frio, além de aumentar os vazios deixados pelo consumo do redutor. Outro fenômeno que afeta na velocidade da reação de redução é a formação de escória. Esses aspectos são analisados neste trabalho e principalmente em processos de auto-redução.

Oct 30, 2017

By Moacir Kuwahara

Nesta pesquisa, foi desenvolvido um material compósito com matriz poliéster, reforçadas com fibras de bambu e de sisal. As fibras de bambu foram extraídas do próprio campus da UFPA e as fibras de sisal obtidas no comércio de Belém. As fibras foram submetidas ao equipamento moinho granulador, com a finalidade de otimizar o corte das fibras, visto que, pelo processo manual gasta-se um certo tempo para obter uma quantidade necessária, para fabricação dos compósitos. E os comprimentos obtidos variaram entre 5 a 15 mm. Os compósitos foram produzidos utilizando-se o menor nível possível de processamento tecnológico nas etapas de fabricação. Foram fabricados 8 (oito) corpos de prova para fração mássica definida com a seguinte proporção 3,90%; a fabricação foi realizada por moldagem manual, usando resina poliéster insaturada com a proporção de agente de cura/resina de 0,33%. As fibras de sisal e bambu foram submetidas a ensaio de tração, determinação da massa especifica e avaliação microestrutural, por microscopia eletrônica de varredura (MEV).

Aug 16, 2017

By Jorge Ganoza

Dado que la metalurgia no es una ciencia nueva -en tanto que los conceptos utiilizados como propiedades geológicas, mineralización, procedimientos de extracción y recuperación de oro son practicados durante mucho tiempo, la variación actual de su nombre, no es determinante. En ese sentido, el presente texto señala algunos aspectos metalúrgicos del oro como: mineralogía de los depósitos de oro, las muestras geometalúrgicas para el programa de pruebas, mezclas de minerales, ley de oro y relaves de cianuración.

May 1, 2013

By Paulo von Krüger

Nas condições adversas do mercado atual, aliadas à exacerbada competição é uma questão de sobrevivência a otimização de resultados. Para tal é imprescindível que os principais insumos, particularmente os mais gravosos sejam criteriosamente selecionados. Os eletrodos de grafite estão entre os itens principais na operação dos fornos elétricos a arco, tanto do ponto de vista técnico, quanto econômico e a escolha correta deste insumo deve contemplar aqueles dois enfoques. Esta escolha se faz dentre as diversas classes, disponibilizadas no mercado: RP, HP, SHP, UHP. O que se pretende no presente trabalho é sugerir uma metodologia que, contemplando o elenco de parâmetros influentes, permita fazer a escolha correta do eletrodo, dentro daquelas classes, tanto sob o enfoque técnico, quanto econômico.

Aug 17, 2017

By Glenn Buchana

El presente texto señala algunos aspectos técnicos y comerciales del dragado del depósito fluvial. Para ello, es necesario conocer el origen y desarrollo del depósito fluvial. El depósito fluvial es una masa de grava superficial, la cual es producto del desmoronamiento y erosión de rocas sólidas que contienen partículas o pepitas de oro, diamante, estaño, platino u otros minerales valiosos que proceden de las rocas o de las vetas. Entre los tipos de depósitos aluviales tenemos: depósitos aislados pequeños y poco profundos, los depósitos de mediana profundidad, depósitos profundos y los marinos. La explotación se realiza a través de tres sistemas: draga cortadora de succión, la dragalínea de cangilones y la planta de tratamiento flotante.

Nov 1, 1979

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984