Search Documents

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

Seismological Society of America, University of California, Berkeley, Calif. Perry Byerly, Secretary. The Bulletin of the Seismological Society of America is issued quarterly. The four numbers each year are collected in a volume; in 1932 the 22nd annual volume was published. The articles contained in the copies of the Bulletin are not, perhaps, of direct interest to a mining engineer but many of them will interest geologists. To indicate the type of articles contained in the Bulletin, the following titles, taken from the current issue, for June, 1932, are given: The Japanese earthquake of march 28, 1925, and the Problem of depth of focus; the earthquake in Santa Monica Bay, California, on August 30, 1930; a new vertical seismography. For copies of the bulletin or information concerning them, address the above.

Jan 1, 1933

By R A. Lynch, D A. Malovichko

The implementation of routine real-time micro-seismic monitoring of open pit mine slopes has been discussed. Some examples of seismic arrays have been given, and a recommendation of suitable seismic sensors made. Unfortunately near-surface sensors are required for good location accuracy, and the effects of reflection, mode conversion and surface waves must be accepted and compensated for during processing of the seismograms. It makes sense that mining at the base of a slope and levels of seismic activity within the slope should be related, and this is confirmed using both 2002-2003 and 2005 seismic data recorded at Navachab mine. An example of how seismic data can be used to gain information about seismically active geological structures has been described. The removal of broken rock, and not blasting nor the breaking of supporting rock, has been found to cause slope micro-seismicity. While the standard Brune source model is suitable for some 20% of the seismic events, unreasonable results are obtained for the rest. A moment tensor inversion has been performed after S-wave splitting and surface effects have been filtered out. This approach confirms a predominantly shear mechanism for a typical high frequency source.

Jan 1, 2006

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

By William Naville

Produtos de consumo em massa causam um grande impacto ambiental, destaca-se que as empresas podem se beneficiar com ações, como a inclusão de objetivos de redução de impacto ambiental e sustentabilidade, nas etapas de desenvolvimento, projeto e seleção de materiais sem aumento nos aspectos econômicos. Três produtos de consumo em massa foram estudados: escova de dentes, embalagem de marmita e blister de medicamentos. Por meio de estimativas e simulações, utilizando-se a ferramenta de energia incorporada do software Eco Audit ®, determinou-se o consumo de energia incorporada e as emissões de CO2 para o uso de alguns materiais em potencial. Simultaneamente, considerou-se nos requisitos funcionais e geométricos a preocupação com o meio ambiente na etapa de projeto. O resultado foi que estes produtos de consumo em massa geram um grande impacto ambiental e a seleção de materiais em conjunto com os requisitos funcionais e geométricos, tendo como objetivo adicional uma redução do impacto ambiental, gera redução do gasto de energia incorporada e consequentemente a redução nas emissões de CO2.

Oct 30, 2017

By F. R. Morral

INDUSTRY has yet to find a universal solution to the problem of engineer personnel selection. Today, the choice of the right man for the right job is even more pressing than ever before. The age of the hard apprenticeship seems to have passed. In its place one finds the interviewer who must determine through personal contact and evaluation of college grades whether a graduate engineer will fit into his company's scheme. The problem, as it is constituted today, may be broken into four parts: Need for better use of human resources (there is a shortage of engineers, scientists, and skilled workers), productivity with higher efficiency, encouragement of personal pride in work performed, and employee's happiness on the job and away from it.

Jan 4, 1953

By C. P. Snyman

Three independent methods of coal classification can be distinguished, namely on the basis of grade, type and rank. The latter two can be determined accurately and unambiguously only by means of microscopical techniques. These three independent variables affect all the coal properties and therefore also the technological behaviour of a particular coal. The influence of the inorganic constituents of coal on the fusibility of the ash and on the length of the slag, and also on fouling and slagging, is discussed. The fractionation of the ash-forming constituents during combustion and gasification of pulverised coal shows that fouling and slagging are not related directly to the fusibility and composition of ash of the coal as a whole. The results of combustion experiments using a drop furnace technique indicate that the ignition temperatures of the light volatiles in the coal, and of the formed char, as well as the burn-out time of the char are more dependent on the rank than on the type or grade of the original coal. High-ash coals, however, apparently ignite at lower temperatures and are more reactive than low-ash coals of similar type and rank. The surface properties of coal, which are important in froth flotation and oil agglomeration, correlate well with the inherent moisture content (and by inference with the heat of wetting and the calorific value) and therefore with the type and rank of the coal. In coal exploration, variations of rank offer the possibility of predicting the presence of an intrusion near the seam, thus contributing to more effective exploration and mine planning.

Jan 1, 1991

By Rosmus P

Improper use of auxiliary ven- tilation units during heading operations may often result in the appearance of hazardous methane accumulations. This is the case especially when roadways are ventilated by a combined system with a short sucking pipe at face end performing as the dedusting installation. Uniform air inflow to the face end facilitates sucking off the dust clouds and creates conditions favourable for formation of local methane accumulations. The highest methane concentration occurs in the cutting zone between the rock cut and the pipe inlet, under the roof and by, the sidewalls. Permanent monitoring of methane concentration at face end employs methane sensors. The most important are: one on the road- header's boom behind the cutting head, and one at the air outlet from the dedusting installation.

Jan 1, 1988

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By Stephanie L. Kaster, John G. Speer, Blake M. Whitley

Niobium-microalloying technology has been increasingly applied in a wide range of steel applications over the past half-century, to increase strength, control microstructure, enhance properties and enable a variety of applications. To achieve desired performance levels, thermomechanically processed microalloyed steels are widely supplied by the steel industry for high volume applications in hot-rolled plate, sheet and structural steels. However, in steel long products and forgings, the final properties are often generated by downstream users, after heat-treatment, surface hardening, forging or wire drawing. Two examples are presented highlighting advancements associated with Nb-microalloying, to enhance microstructures and properties developed during thermomechanical and/or downstream processing. In the first example, a 0.02 wt. pct. Nb addition was made to a medium-carbon bar steel intended for induction-hardening applications requiring fatigue and fracture resistance in bending and torsion. The Nb addition as well as thermomechanical bar processing led to beneficial refinement of both the pre-induction and post-induction microstructures. In the second example, a 0.01 wt. pct. Nb addition to a high-carbon wire rod was found to refine the pearlite colony size and interlamellar spacing, and increase the hardness.

Oct 1, 2019

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

Shafts are the most important workings in the underground mines. Their technical state to a large extent determines the safety and efficiency of mining operations. However, in many cases periodically performed inspections show unsatisfactory technical state of the shaft lining (local defects, cracks, cavities, losses of the outer surface of the lining or, in case of the bricks, losses of the masonry). The most common cause of these types of damage is progressive deterioration of the lining material, impact of aggressive mine waters, impact of mining operations, deformation of the lining due to the rock mass saturation, seismic activity or periodic freezing of the lining in the upper part of a shaft. The paper presents legal requirements associated with the use of mine shafts in Polish coal mines as well as the ways and range of their control. Furthermore, examples of typical damage to shaft lining and ways to repair it, such as additional bolting, filling cavities or a wire mesh and shotcrete installation, are shown. In the final part, the paper presents a short example of a shaft, in which damage to the lining was one of the main causes of the shaft's failure. Due to the damage to the shaft lining, at the depth of approx. 65.0 m, the shaft was spontaneously filled with overburdened soil material. It resulted in a large crater to come to the surface, which, in turn, caused damage to the buildings and facilities present in the impact zone. On the surface the diameter of the crater was approx. 60.0 m, its depth approx. 11 m and the estimated volume was of about 30,000 m³. The disaster also caused disturbance in the ventilation of two neighbouring mines and the increase in methane hazard. Given the size of the crater, the measures to eliminate consequences of the catastrophe were undertaken in several stages.

Aug 1, 2013

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By Carl H. Eckert, James P. Berson

INTRODUCTION The demand for specialty metals in industrial applications is in it's healthiest state since the late 1970'8, and several specific markets are recording record sales. Such metals as gold, silver, zirconim., titanium, beryllium, gallium, germanium, the platinum group, and the lanthanides accounted for sales in excess of $2 billion in 1985 among the end uses covered in this report. Although specialty metals as a group have suffered the effects of recessionary pressures in the past, these metals have proved more resiliant than such large volume metals as copper and nickel. This is due to the unique physical properties they possess which makes the threat of substitution or replacement through technological development uneconomic. The outlook for these specialty metals is optimistic in electronics, catalysts, ceramics, and alloys, and their specialty status results .in a combined average annual growth in demand of 7% through 1990. WHAT MAKES THESE METALS SPECIAL? Such characteristics as electrical conductivity, corrosion resistance, catalytic activity, thermal stability, and optical properties allow the term specialty to be applied to these metals. More importantly, all of these metals possess more than one of these qualities, as shown in Table 1. [ ] These five major functions are important in the end uses for these metals, although the specific applications vary somewhat. Conductivity in term of low or high electrical resistance is of obvious importance to electronics manufacturers. Producers of circuit boards or semiconductors require such metals as gold, palladium, platinum, and gallium due to their low electrical resistivity. However, these producers also require such metals as beryllium in the oxide form for insulation components because of the compound's low electrical conductivity. Although the lanthanides' conductive characteristics are not particularly attractive in electronics, they are of great importance to alloy manufacturers producing permanent magnets for automotive and computer applications. Corrosion and wear resistant properties are extremely attractive to a number of end-use industries, particularly in view of the estimate by the United States Bureau of Mines that $10 to $50 billion in losses are experienced by U.S. industry due to equipment corrosion and $100 billion due to equipment wear. The strength of high purity titanium and zirconium make these metals the obvious choice for corrosion and wear resistance particularly in the chemical processing industry, where the ability to maintain integrity in corrosive environments is a must. Heat exchangers, nuclear control rods, and a number of parts in jet engines have benefited greatly from the use of these metals. However, such other specialty metals as beryllium, and the lanthanides also improve the wear or corrosion resistance in various products. For example, a beryllium-copper alloy contact maintains it's spring like character, and does not loose this character after repeated use, which could result in the loss of an electrical contact. Lanthanide, in the form of cerium oxide, is commonly employed in alloys used to produce catalytic converter casings for the purpose of reducing damage by corrosive road salt. In some instances, the catalytic activity of several of the specialty metals assists in the economic production of other materials. However, the importance of specialty metals in catalysts is most apparent in catalytic converters for emission control. Platinum, palladium, and rhodium are

Jan 1, 1986

By R. M. Mashishi, T. Malehase, O. J. Okonkwo

The concentrations of selected trace elements (As, Cd, Hg, and Pb in run-of-mine (ROM) coal, discard, and coal product were investigated to assess the efficiency of beneficiation in reducing trace element concentrations and ascertain any implications regarding environmental compliance to regulatory frameworks. Samples were collected from a colliery in Mpumalanga Province twice a month for a period of 24 months. The samples were ashed to approximately 0.21 mm, then digested in a mixture of 70% HNO3 and 40% HF and analysed using inductively coupled plasma-mass spectrometry (ICP-MS). Except for Pb, the mean concentration of all elements decreased from the ROM stage to the coal product stage. The order in which trace elements occurred from the highest to lowest throughout the production chain was Pb>As>Hg>Cd. With the exception of Cd, the mean trace element concentrations in the discard were above the total concentration threshold (TCT) set for landfill disposal. The As, Hg, and Cd concentrations in the product were well below the thresholds for all land uses. However, Pb concentrations in the product coal were above legal limits, which is of concern with regard to environmental compliance and the performance and marketability of the product.

Dec 13, 2023

By K. Stankiewicz

Projects as regards state-of-the-art mechatronic systems aiming at increase of safety in the mining industry and at improvement of coal production technologies, which have been completed at the KOMAG Institute of Mining Technology, are presented. These projects cover automation, monitoring and visualization systems, systems for implementation of artificial intelligence techniques, and database recording systems. iRIS system for electronic marking, identification, and recording of components of powered roof supports, which was implemented in 31 Polish mining enterprises, is presented as an example of the work directly associated with an increase of operational safety. Specialists from KOMAG, ELSTA, Ltd., and Silesian University of Technology in Poland, have developed flexible, configurable, and scalable system for data management, which refers to all fixed assets of mining enterprises, meeting the requirements of users as regards marking and identification of fixed assets. The system for control of roadheaders using intelligent algorithms, based on artificial intelligence techniques is also the example of innovative actions. This system aims at increasing the safety and effectiveness of teamwork due to a possibility of remote, semiautonomous operation. Introduction of artificial intelligence technology enables adaptation of roadheader mining system to the present mining-and-geological conditions. Moreover, work aiming at implementation of state-of-the-art system for control of mine jig?s beneficiation node, integrating machines and equipment in one system, is carried out as regards automation, information integration, and visualization in coal beneficiation process. Work on recovery and conversion of thermal energy, which is a by-product during operation of machines and equipment, especially mine diesel drives, is presented. Systems for energy recuperation are more and more important due to the necessity of continuous increase of power production efficiency.

Aug 1, 2013

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By Dr. O’Neil Thomas J., Donald W. Gentry

"There is nothing so disastrous as a rational investment policy in an irrational world. " John Maynard Keynes INTRODUCTION The principles of time value of money concepts were discussed and illustrated in Chapter 3. The importance of time value of money and the role it plays in the discipline of engineering economy have been well established. Chapter 9 further illustrates that project evaluation criteria that fail to consider this aspect are seriously deficient in providing appropriate capital budgeting decisions. Obviously future project receipts and expenditures must be discounted to permit valid comparisons with current cash flows. Although the concept of discounting is widely accepted, the selection of the appropriate discount rate has been the source of considerable debate and much disagreement. This chapter, then, provides an overview of the theoretical and practical considerations for determining or calculating the appropriate rate for discounting, the corporate cost of capital. Note specifically that the assumption of constant business risk among the various investment alternatives is maintained throughout this chapter. THE INTUITIVE APPROACH The fact that interest exists suggests that all money has a cost associated with its use. The cost of this money may be the result of either explicit or implicit charges or some combination of the two. Any time an individual or a firm consumes less than the total earnings generated in a given time period that individual or corporation has either consciously or unconsciously decided to "invest" these excess funds in some type of activity. For instance, the individual or corporation may decide to invest the excess funds in tangible property, place the funds in a money market account, or simply keep these funds in cash. In any case, these funds have been invested in some type of activity which promises the investor some return on the invested capital. Remembering that the firm's primary objective should be the maximization of shareholder wealth, then intuitively it seems reasonable to suggest that the firm should not invest in any project where the anticipated return does not exceed the cost of funds (capital) committed to the project. Indeed, if the firm always invests in projects having returns in excess of the cost of capital committed to them, then the wealth of the firm (as measured by the price of common stock) should be in-

Jan 1, 1984