Search Documents

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.

By John J. Jonas, Hong Qin

Cylindrical samples of pure titanium were subjected to uniaxial compression at room temperature, leading to the formation of three generations of twins. Many primary contraction twins were observed as the initial texture was favourable for their formation. Numerous secondary extension twins formed within the primary contraction twins and some tertiary contraction twins within the secondary extension twins. The orientations of these three generations of twins were determined by electron backscatter diffraction techniques and their associated Schmid factors (SFs) were calculated. The formation of the twin variants selected in each generation and the absence of certain potential variants are accounted for by rotating the twinning displacement gradient tensor expressed in the twin system reference frame into the crystallographic reference frame of the relevant neighbouring grain. The presence of the observed primary, secondary and tertiary twins is explained in terms of the ease of imposing the required accommodation strains on the neighbouring grains. By contrast, certain first, second and third generation potential high SF twins were absent because their formation would have required accommodation by the most difficult deformation mode: pyramidal glide.

Jan 1, 2015

By L. Jiang

The evolution of twinning in an AM30 Mg alloy was examined by uniaxial tension and compression testing at temperatures from ambient to 250°C and a strain rate of 0.1/s. The samples were cut along the extrusion direction from extruded AM30 Mg alloy tubes. Specimens deformed to various strain levels were examined by optical microscopy and electron backscattered diffraction (EBSD) techniques. The results indicate that the initial extrusion texture plays an important role in the formation of different types of twins and that the twinning behavior also depends on the strain path. Contraction and double twinning are the dominant twinning mechanisms in uniaxial tension, while extension twinning prevails in uniaxial compression. The different twinning behaviors are shown to be responsible for the sharply contrasting strain hardening characteristics of the experimental flow curves.

Jan 1, 2006

By A. J. Phillips, C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury, have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. [ ] Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2 A determination of the composition

Jan 1, 1928

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By Albert J. Phillips

As EARLY AS 1824, Haidinger1 described crystals of native copper that were, according to Dana,2 "probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,

Jan 1, 1928

By Albert Phillips

As EARLY As 1824, Haidinger1 described crystals of native copper that were, according to Dana,2 "probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by. electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,

Jan 1, 1928

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.1 This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material in. which the crystals here dealt with were grown was made from 1/8-in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, ass nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. MEASUREMENTS The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, ?, from one direction of the wire axis, and an azimuth or longitude, [ø], from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most. of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

Jan 1, 1928

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By C. S. Barrett, C. T. Haller

TWINNING in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study' concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: I. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation. 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. MATERIALS AND METHODS The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. [ ] X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on {102} planes causes a reorientation of the crystal lattice by 86°, it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallographic observation, for it was found

Jan 1, 1946

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well.

Jan 12, 1951

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama's 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By G. B. Johnston

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1990

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996