Search Documents

By V. Srajer

The loading and hauling equipment simulation model was developed to satisfy, the requirements and need of the mining industry in western Canada. It is expected the model will be used to determine the' impact of various combina¬tion of loading and hauling equipment, company policies and maintenance procedures, haulage requirement, to evaluate possibilities, of the use of truck monitoring and dispatch systems, and to access loading and hauling equipment productivities. To evaluate the model, and to access its capabilities in addressing the above requirements, the model was validated. The validation was based on the following: 1. Running the model in-house to evaluate its structure, 2. Running the "test case" by timing models developed elsewhere to compare the results of simulation, 3. Soliciting of model critique from outside agencies, and 4. Comparison of calculated data with real time study data. The presented paper provide overview of the validation processes and summarize" results obtained during comparison and evaluation studies.

Jan 1, 1989

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By Jiqing Zhang, Jon C. Yingling, Andrzej M. Wala, Richard Ray

The purpose of this paper is to present how Computational Fluid Dynamics (CFD) simulations can be used to study the flow across the main airways of a mine ventilation system. in particular, the flow through the transition zone between the upcast shaft and main fan ductwork was investigated. These studies consider potential design modifications of this transition zone to reduce the energy cost. Although CFD has many advantages, it does not completely eliminate the need for experiments, which are still needed to validate numerical solutions. For this reason, data collected during actual mine tests and CFD simulations are compared in this pa- per. This comparison allows a better understanding of the flow phenomena. Moreover, once the numerical solutions have been validated, CFD can be used with better confidence to predict the effect of changes in ductwork configurations on energy losses. CFD reduces the number and cost of tedious experiments, while enabling a broader scope of design comparisons.

Jan 1, 1997

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

By Afranio Marcio Costa

No lingotamento contínuo a busca pelo aumento de produtividade tem sido realizada com sequências longas, ou seja, várias corridas e muitas vezes com aços de diferentes composições químicas. Isso resulta na geração de placas de mistura e vários trabalhos buscam entender este processo. Este estudo tem como objetivo validar o modelo matemático de mistura existe no lingotamento da Gerdau Ouro Branco para garantir a correta aplicação da região de mistura, visando atender às especificações dos produtos, norma ASTM A36. Os resultados encontrados nas placas amostradas confirmaram a eficiência do modelo para estimar a zona de mistura. Além disso, para garantir a aplicação dessas placas na norma estudada foi utilizado o modelo de previsibilidade de propriedades mecânicas existente na laminação de chapas grossas. Finalmente, os resultados reais de composição química, limite de escoamento e resistência encontrados nas chapas avaliadas confirmaram as previsões dos modelos e atenderam às especificações do aço.

Oct 30, 2017

By Gustavo Henrique Bolognesi Donato

O projeto e a operação de estruturas que podem vir a conter trincas demandam estudos de integridade estrutural suportados por propriedades mecânicas à fadiga e à fratura advindas de ensaios experimentais (p. ex.: curvas J-R ou da/dN vs. ?K), sendo tais experimentos altamente dependentes da medição instantânea do tamanho da trinca. Essa medição em muitos casos é realizada com base na variação da flexibilidade com o crescimento do defeito. O objetivo do presente trabalho é validar experimentalmente soluções numéricas recentes de flexibilidade elástica que descrevem o tamanho instantâneo de uma trinca em corpos de prova de geometria C(T) e SE(B) incorporando efeitos tridimensionais. Ainda, objetiva comparar tais soluções com as disponíveis nas normas ASTM vigentes. Corpos de prova C(T) e SE(B) foram usinados conforme as referidas normas e testados em máquina universal de ensaios MTS 810.25. Na sequência, os dados obtidos foram convertidos em valores de flexibilidade normalizada (µ), determinando-se o tamanho de trinca (a) esperado com base nos referidos equacionamentos. As previsões de tamanho de trinca geradas foram comparadas com medições reais da profundidade de trinca obtidas de fractografias das amostras após separação final. No geral, tanto as soluções da ASTM como de Moreira (2014) foram consideradas acuradas e com erros máximos abaixo de ~ ±1,5%. No entanto, os resultados mostram equivalente aderência experimental das soluções disponíveis nas normas ASTM com as de Moreira (2014) para amostras C(T), mas melhor desempenho das propostas de Moreira para amostras SE(B) de variadas geometrias e profundidades de defeitos.

Aug 17, 2017

By Miguel Ângelo Menezes, Carlos Alberto Alves Viana

O presente trabalho possibilita o entendimento e a análise dos processos de conformação a quente dos metais. Isto, pela validação experimental do modelo de Johnson-Cook, para descrever o comportamento dos materiais no regime plástico, para grandes deformações, às altas taxas de deformações e nas altas temperaturas. Um entendimento dos parâmetros do modelo, utilizando-se um método analítico numérico simples, rápido e confiável foi desenvolvido anteriormente pela linha de pesquisa em Conformação Plástica dos Metais na UNESP – Campus de Ilha Solteira, obtendo-se as constantes empíricas do modelo referido. É proposto nesse trabalho a validação experimental do método simplificado para determinação dos parâmetros empíricos do modelo de Johnson-Cook através de um ensaio de tração a quente, considerando as propriedades mecânicas dos materiais analisados experimentalmente e/ou de dados de materiais disponíveis na literatura. De maneira geral, os resultados experimentais foram satisfatórios para o aço AISI 1045 à temperatura de 500 ºC, ensaiado à taxa de deformação de 1000 s-1, quando comparados aos resultados teóricos previstos pelo modelo proposto por SCADUTO e MENEZES. Particularmente, foi possível evidenciar erros máximos de 1,33% para o parâmetro n, 13,15% para o parâmetro B, 295,00% para o parâmetro C e 4,14% para o parâmetro m.

Nov 11, 2019

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By John D. Gill

THIS paper assumes the incontrovertible nature of the statement that the validity of competition in the nonnatural resource industries is established firmly on the rate and extent of the economic development of the United States. It then demonstrates the nonexistence of any condition within the petroleum industry that would invalidate the principle of competition as applied to it. It points to the benefits that competition has effected in the oil industry and the reasons why the practice of the competitive principle should continue to keep the industry virile and progressive in meeting the requirements of future generations for the kind of products natural to it. Finally, it pleads for a clearer view of the affairs of the oil industry by seeing them against a background of the whole economy. INTRODUCTION Even a few years ago there would have been only an academic reason for presenting before this Institute a paper on the validity of competition in the oil industry or any other natural resource industry; today there is no more practical subject for this body to consider. In social importance it transcends attempted solutions of perplexing technical problems; and even the numerous legal and economic problems that grow out of administration of state regulatory measures appear to be of secondary importance because they would cease to exist if competition were abolished. The aspiration of certain elements of the Federal Government to acquire control of the oil industry has long been suspected The vital need for petroleum in the national defense ... confirms my belief in the urgent need of Federal legislation to safeguard our petroleum supply through prevention of waste and by establishment and maintenance of sound economic conditions in the oil industry... . But also it may be dismissed with this mere mention of it because it predicates government control and the abandonment or broad reduction of competition on a war emergency. Clearly, the fight for a nation's life may justify a government's control over men and resources that would be abhorrent and economically enervating under conditions of national security. More pertinent to the present matter, because it appears expressive neither of a personal ambition nor of an emergency condition but rather of the long-range view of a certain school of conservationists, is the pronouncement of no less an authority than the Attorney General of the United States, who has been repeatedly quoted by the press as saying that the American Petroleum Industry constituted a case "where the principle of conservation of an exhaustible and irreplaceable resource should replace the principle of competitive exploitation." The significance of this statement in the light of the commonly accepted meanings of the " principle of conservation" and of the "principle of competitive ex-

Jan 1, 1941

By Ruilin Yang

Based on large amounts of field data, this paper evaluates the validity of the above equations. During the evaluation, the different selections of the frequency in the equations were examined with field data. It is found that when they are used to estimate the vector sum values the above equations could result in large deviations from the values obtained directly from the field measurements or the waveform integration. The simple equations may be used to make rough estimations for single components of blast vibration provided that appropriate safety factors are taken into account. For single component vibration, the principal frequency (from ‘zero-crossing’) seems more effective to describe the blast vibration than the dominant frequency (fron FFT) for vibration peak value estimation using the simple equations.

Jan 1, 2012

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don't allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir's law is discussed for different operating conditions.

Jan 1, 1996

By J. -P. Chilès

The discrete Gaussian model is a very popular change-of-support model for estimating block grade distributions. It is designed for a stationary random function Z(x) that is regarded as the transform of a stationary random function Y(x) with Gaussian marginal. It is based on an assumption that is not fully true and thus constitutes an approximation to the exact solution. We examine the effect of this approximation on the modelling of the marginal distribution of block values of a lognormal random function. The initial discrete Gaussian model and a variant of that model are considered.

Jan 1, 2014

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998

By Carlos Astorga, Juan Miranda

La valoración de activos mineros es una práctica continua en el tiempo y requiere de equipos multidisciplinarios para poder realizarlas de manera óptima. Existen diversos métodos que se aplican en función de la etapa de desarrollo en que se encuentran los proyectos o empresas en marcha. En el presente trabajo abordamos dos de ellos para empresas globales, en el primer caso analizamos el Método de Múltiplos para empresas auríferas y cupríferas y el Método de Transacciones Comparables para auríferas y argentíferas.

May 1, 2008

By Prosper Lamothe

El presente texto describe la metodología ad-hoc para evaluar proyectos de Inversión estratégicos a través de la flexibilidad y la teoría de opciones reales. La clave de dicho enfoque metodológico radica en realizar la mejor proyección del precio de los metales aplicando las mejores prácticas mundiales al respecto. Para ello, se analizan una gran variedad de modelos concluyendo que el mejor modelo a aplicar, debe ser la simulación del precio del metal con reversión a la media con saltos de tipo aleatorio.

Sep 9, 2007

By Manuel Viera

El modelo Viera-Hurwick es una herramienta para la valoración económica de activos mineros. Es práctica, de fácil aplicación y arroja muy buenos resultados para un proceso de compra-venta. Se presenta el caso de estudio real del prospecto Greenfield Manuelita I Ongon Patazun, que se evalúa con esta metodología a nivel de exploración básica. Después de aplicar técnicas tales como árbol de decisiones, flexibilidades, Hurwick, estadística bayesiana, Hoskold, opciones reales, entre otras, se concluye que esta metodología, por su simpleza, arroja buenos y rápidos resultados que concuerdan totalmente con otros métodos y son plenamente aceptados por el código australiano VALMIN de valoración económica de activos mineros.

Sep 20, 2019

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011