Search Documents

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

A preliminary research and development program dated April 25, 1974, was prepared for Development Engineering, Inc. (DEI) for laboratory, field and other engineering studies on the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included discussions on the peculiarities of retorted shale materials to be investigated and discussions of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I Program Development. II Exploratory Laboratory Tests on Old U.S.B.M. Retorted Shale. III Laboratory Tests on Pilot Plant Retorted Shales. IV Laboratory Tests on Retorted Shales from the Semi-Works Plant.

Jan 1, 1976

By Sheridan J. Rodgers

The quantity and behavior of gases in metal and nonmetal mines were monitored to provide background information on feasibility of incipient fire detection systems. Monitoring was conducted during working and nonworking periods at intake air, return air and working places. Gases generated during diesel operations and shot firing were of particular interest. Gases which were monitored were CU, C02, N0, N02 and S02: submicron particulate concentrations were monitored also. Commercially available instruments were used and included nondispersive infrared, electrochemical and chemiluminescent types. The ratios of the various gases generated during diesel operations and shot firing were similar to those expected from an incipient fire, with the exception of the C02/NOx ratio, which is sufficiently different to be considered for early fire warning. Samples taken near leaking bulkheads showed high C02 levels and low C0 levels, the reverse of anticipated behavior in coal mines.

Jan 1, 1976

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By S. H. E. Phillips

This report describes the initial feasibility, the development and the field demonstration of a system for shaft sinking employing a high energy mechanical impact rock breaker and a compatible muck disposal system. The increased shaft sinking rates, decreased costs and improved safety conditions obtainable by the elimination of the less efficient conventional drill-blast-muck cycles are discussed. Four shaft sinking concepts utilizing the impact rock breaker in various shaft configurations are developed and the field demonstration in a rectangular shaft is described. The progress achieved, the problems and their remedies and the proposed modifications to improve the machine are described.

Jan 1, 1978

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

[ ]

Jan 1, 1981

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976