Search Documents

By J. F. Fidiam, T. F. Ford, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By T. F. Ford, J. F. Fidiam, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By Ralph J. Schilthis

Several investigators1-8 have reported evidence of the existence of native or connate water in oil-and-gas-bearing strata. Both water and salt have been detected in cores of oil sands that yielded oil and gas exclusively when produced. Electrical logs often reveal unexpectedly low resistivity through oil and gas sands, indicating the presence of some material that is a considerably better conductor of current than oil and gas. Furthermore, calculationsg of the oil and gas content of reservoirs based upon production and reservoir-pressure decline data indicate appreciably lower values than are arrived at under the assumption that the pore space is occupied completely by oil and gas. Origin and Occurrence of Connate Water in Oil-and-gas-bearing Formations The view has been expressed, 10-15 and is generally agreed upon, that the expulsion of oil and gas material from source beds and the subsequent migration and accumulation occurred in the presence of salt water. As the strata that usually form reservoirs for oil and gas were laid down by, or in the presence of, ancient seas, the pore space within the strata must have been saturated with salt water before the entrance of the oil and/or gas. Thus, the accumulation of oil and/or gas in the upper regions of structures suitable for reservoirs must have required displacement of the connate water therefrom. In the absence of any forces other than gravitational, it would be expected that the displacement of the connate water out of the zones finally occupied by gas and oil would be complete, and that the vertical distribution of gas, oil, and water in a reservoir would be strictly in the order of their densities. Apparently, however, surface and interfacial forces that will not permit complete segregation of the fluids are active within the capillary spaces comprising a reservoir. The effects of these forces on both accumulation and production of oil and gas have been the subject of study by a number of investigators.16-37 In general, the view is held that the character of most materials that make up the reservoir rock leads to preferential wetting of the rock by

Jan 1, 1938

By W. N. Lacey, B. H. Sage

In recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity † of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Voge133 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith20 at 63° and 212° F. Ishida14 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz30 measured the viscosity of propane at atmospheric pressure, from 83° to 530°F., by the use of a short capillary tube. Rap-penecker2' determined the viscosity of gaseous isopentane at elevated temperatures. Day6 made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in.‡ to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart7 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington9 by the rotating-cylinder method. Kellstrom15 has rec,ently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made.

Jan 1, 1938

By J. H Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. H. Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By J. R. Coleman, G. L. Corrigan

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By G. L. Corrigan, J. R. Coleman

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By L. S. Reid, R. L. Hunntington

The study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating conditions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1l,2,3 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils. The work of Wyckoff and Botset4 has constituted a major step in the interpretation of heterogeneous fluid flow; especially their concept of

Jan 1, 1938

By Eldon N. Dunlap

Recently the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occurrence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of interstitial water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a correction is made for the volume of water that occupies a portion of the effective pore volume of the reservoir. Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also to his interest to know to what extent the presence of varying amounts of interstitial water influences the permeability of the sand to oil.

Jan 1, 1938

By H. E. Gross

Recently, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 Ib. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 Ib. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rams holding a back pressure of 2900 Ib. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe²O³) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district. Laboratory Study of Heavy Muds To foster the use of the plentiful and extremely heavy mineral, galena, research has been done recently at the University of Oklahoma to determine the mud-making properties of this substance. For comparative

Jan 1, 1938

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By E. Beril

This may be a most unnecessary paper—from what does crude oil come and how was it formed. Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important industrial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion. Older Theories There is no doubt that plants were the parent material of coals, but opinion is divided as to the parent material of crude oil and asphalts. One group of specialists believed that they were formed from dead fish. The hydrocarbons of crude oil were formed by the splitting off of CO² from fatty acids formed by the saponification of the fat (glycerides) of fish. Enormous quantities of crude oil are present in many places on the earth, very often in several nonconnected horizons at the same location. This could hardly be explained by the so-called "catastrophe theory," which states that fish died through the entrance of salt water into fresh water, and vice versa. Furthermore, this theory cannot explain the presence of aromatic hydrocarbons, which can be found in nearly all oils, especially in the oil of the Netherlands Indies, which has more than 50 per cent of aromatics. Geological and chemical observations both lead to the belief that the temperature of formation of asphalt, crude oils and coals, perhaps with a few exceptions, did not exceed 200° C. Chlorophyll and haemin derivatives, which decompose above 200° C., have been found in all these materials by Treibs and others. Thermodynamic considerations show that the temperature necessary for the conversion

Jan 1, 1938

By B. H. Sage, R. T. Carter, W. N. Lacey

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941

By W. N. Lacey, R. T. Carter, B. H. Sage

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941