Search Documents

By R. L. Templin

In treating a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum. Factors That Must Be Considered Simultaneously with Cold Working So many other factors affect the physical properties of a metal that it is necessary to consider these factors simultaneously with cold working; their effects vary in magnitude with the amount of cold work present. The most important of these factors are: (I) chemical composition, (2) structure, (3) temperature of working, (4) character of working, (5) rate of working, and (6) methods used for measuring results. For

Jan 1, 1930

By Howard Scott

Invar is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100" C. and soon reaches the value of copper. Guillaumel met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detrimental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

By Edmund S. Davenport

The production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium. Materials and Methods The thorium employed in this investigation was made from pure thorium oxide (ThO2) by the Ca-CaCl2 reduction. The washed and dried metal powder was pressed into bars approximately 0.160 in. dia. and 10 in. long, at a pressure of 75,000 Ib. per sq. in. The bars were heat-treated in vacuum at 1175' C. for 1 hr. This treatment yielded ingots sufficiently dense and coherent for mechanical working. Thorium has been successfully worked without a protective metallic covering, but for the purposes of this investigation it was more convenient to inclose the ingots in soft iron tubes and swage or roll cold to the desired sizes. The iron sheath was dissolved with nitric acid, leaving the cold-worked thorium exposed. Chemical Analyses Analyses of typical samples of the material used in this work arc given in Table 1. Thorium powder oxidizes in moist air, even at room temperature; no unusual precautions were taken to prevent such oxidation of the material used in this investigation. A certain amount of oxidation probably takes place during pressing; certainly during heat-treating unless a very slow heating schedule is employed. These factors account

Jan 1, 1930

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By H. L. Brunjes, G. B. Gould

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

By R. S. Bradley, B. K. Miller

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

By B. K. Miller, R. S. Bradley

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By Thomas R. Cunningham, A. B. Kinzel

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By A. B. Kinzel, Thomas R. Cunningham

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By James Norman, Oliver C. Ralston

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by Froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each or clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1942