Search Documents

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

By Donald E. Cummings

Measures appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-l9 has accumulated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors—the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Control of the danger arising out of prolonged contact with pernicious airborne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects—one, medical; the other within the province of the engineer. I—Factors Comprising Degree of Individual Susceptibility Thorough investigations conducted among miners who have labored for years in the presence of recognized silicosis hazards usually reveal an impressive difference in the injury incurred by men whose exposure to dust has been nearly identical. After a quarter century underground, one individual is short of breath and incapacitated with miners' complaint, while a fellow workman suffers no pulmonary embarrassment and is in good health. Physicians ascribe this oft-observed difference in reaction to individual susceptibility and express a universal regret when they deplore the fate that chose to make the predisposed youth a miner rather than a farmer. To trust the health of miners to fate at the present time is even more unfortunate, because many of the factors that influence man's susceptibility to dust are known, and can be accurately determined by competent medical methods. Among the most important factors comprising susceptibility to injury by dust are the anatomical peculiarities of the individual's respiratory mechanism, his physiological response to the inhalation of dust, his previous dust, exposure, the existence of pulmonary infections or other pathological processes in his lungs, his age,

Jan 1, 1940

By Donald E. Cummings

Measures appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-l9 has accumulated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors—the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Control of the danger arising out of prolonged contact with pernicious airborne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects—one, medical; the other within the province of the engineer. I—Factors Comprising Degree of Individual Susceptibility Thorough investigations conducted among miners who have labored for years in the presence of recognized silicosis hazards usually reveal an impressive difference in the injury incurred by men whose exposure to dust has been nearly identical. After a quarter century underground, one individual is short of breath and incapacitated with miners' complaint, while a fellow workman suffers no pulmonary embarrassment and is in good health. Physicians ascribe this oft-observed difference in reaction to individual susceptibility and express a universal regret when they deplore the fate that chose to make the predisposed youth a miner rather than a farmer. To trust the health of miners to fate at the present time is even more unfortunate, because many of the factors that influence man's susceptibility to dust are known, and can be accurately determined by competent medical methods. Among the most important factors comprising susceptibility to injury by dust are the anatomical peculiarities of the individual's respiratory mechanism, his physiological response to the inhalation of dust, his previous dust, exposure, the existence of pulmonary infections or other pathological processes in his lungs, his age,

Jan 1, 1940

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By J. T. Burwell, J. Wulff

As is well known, the alloys of iron containing 18 ± per cent chromium, 8* per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composition (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff,1 it was decided to investigate the phenomenon by electron diffraction methods. Apparatus The apparatus used (Fig. 1) was a hot-filament type employing movable slits, similar to that described by Germer.2 The sample-to-photographic plate distance was 69 cm. and the accelerating voltage 30 kv. Since electrons do not in general follow geometrical paths, it is necessary that either the electron source or the sample be movable in a plane normal to the beam. In this case the sample is fixed and the electron source is movable. The source is adjusted until the shadow of the sample appears in the brightest part of the beam as viewed on the fluorescent screen, then the slits composing the two pinholes are inoved into position one by one. The system is evacuated by means of a mercury diffusion pump backed up with a Cenco Hypervac oil pump. Pressures lower than 10- mm. of Hg are read on a calibrated ionization gauge.

Jan 1, 1939

By J. T. Burwell, J. Wulff

As is well known, the alloys of iron containing 18 ± per cent chromium, 8* per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composition (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff,1 it was decided to investigate the phenomenon by electron diffraction methods. Apparatus The apparatus used (Fig. 1) was a hot-filament type employing movable slits, similar to that described by Germer.2 The sample-to-photographic plate distance was 69 cm. and the accelerating voltage 30 kv. Since electrons do not in general follow geometrical paths, it is necessary that either the electron source or the sample be movable in a plane normal to the beam. In this case the sample is fixed and the electron source is movable. The source is adjusted until the shadow of the sample appears in the brightest part of the beam as viewed on the fluorescent screen, then the slits composing the two pinholes are inoved into position one by one. The system is evacuated by means of a mercury diffusion pump backed up with a Cenco Hypervac oil pump. Pressures lower than 10- mm. of Hg are read on a calibrated ionization gauge.

Jan 1, 1939

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By L. W. McKeehan, W. C. Elmore

The magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined1, "or investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators:' have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement ill the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. Specimens The following list describes the specimens used in the present investigation. Designation Description A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which lie gave the following typical analysis: C, 0.05; P, 0.038; S, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick. By X-ray analysis angles between disk normal and [100] 75o, [0101 76" [00l] 21o. A2 Same as A1 except: diameter 0.75 cm. A, Same as A1 except: diameter 0.68 cm.

Jan 1, 1936

By L. W. McKeehan, W. C. Elmore

The magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined1, "or investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators:' have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement ill the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. Specimens The following list describes the specimens used in the present investigation. Designation Description A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which lie gave the following typical analysis: C, 0.05; P, 0.038; S, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick. By X-ray analysis angles between disk normal and [100] 75o, [0101 76" [00l] 21o. A2 Same as A1 except: diameter 0.75 cm. A, Same as A1 except: diameter 0.68 cm.

Jan 1, 1936

By Charles S. Barrett, Robert F. Mehl

The system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that developed by Bijl l (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1930

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942