Search Documents

By G. R. Drennan, N. J. Wagner, M. J. T. Sebola

The Soutpansberg Coalfield hosts South Africa's hard coking coal reserves. However, coals in this region are understudied compared to other coalfields in the country. This study characterizes the properties of fine-float fraction samples extracted from a wide diameter borehole core in the Makhado Project, Tshipise sub-basin, Soutpansberg coalfield. Conventional analyses were used to determine the coal quality, petrographic composition, mineralogy, geochemistry (including trace element and rare earth element composition), and free swelling index of samples from six coal horizons and three partings from the economic No.6 Seam. The coal samples are classified as medium rank bituminous C coals (0.88 %RoVmr, 0.92 %Rmax) and are highly vitrinitic in composition (97 vol% mineral matter free (mmf)). The samples show strong caking potential (FSI of 9). The total rare earth concentrations range between 570 and 3193 ppm in the ash samples. Preliminary analysis show all but two samples are promising sources of rare earth elements as the total concentrations exceeded the 1000 ppm cut-off grade. Further research is required to confirm these preliminary findings.

Aug 2, 2022

By D Craw, P V. Angus

Gold mineralisation at Macraes occurs as late quartz-carbonate veins within a body of sheared and hydrothermally altered Otago Schist, the Intrashear Schist. The alteration is characterised by the presence of rutile and the absence of epidote and titanite, indicative of an alteration fluid containing >10 mol per cent CO2. In areas of high strain, a fabric of black microshears develops, gradational to mylonitic cataclasite in the high strain zone adjacent to the hanging wall of the duplex shear zone. The microshears contain hydrothermal graphite, inferred to have been deposited from a methane-rich fluid. The mylonitic cataclasite is characterised by abundant pyrite, the absence of albite and extreme grain size reduction. Gold recovery in the CIL processing plant at Macraes can drop to 50 per cent or lower for some unfavourable ore types. Preg-robbing by a component in the ore, possibly graphite, was suspected as the cause. Mylonitic cataclasite was identified as the lithology responsible for the poor recoveries, with the capacity to bind about 30 ppm of gold in the leach tanks. A program of detailed geochemistry and quantitative grain-size measurement using Coulter analysis was undertaken to identify specific mineralogical factors associated with preg-robbing. The results indicate that pyrite, graphite, and extreme grain-size reduction are the factors associated with highly preg-robbing ores at Macraes. The evolution of the mylonitic cataclasite is accompanied by strong potassium enrichment, as muscovite, and depletion in sodium as albite is removed. This suggests that a simple powder XRD ratio of the albite to illite peaks would suffice to distinguish the preg-robbing ore for grade-control purposes.

Jan 1, 1999

By J. M. Barnard, M. P. Brandt, L. E. Korwin-Kossakowski, W. H. Smith

Petrographic analyses of coal rank and maceral-group composition are widely used in the characterization of coal. This paper describes the use of an image analyser (IBAS Kontron) for fuly automated measurements of the rank and maceral groups of seam coals. The rank is then derived from reflectance histograms, or 'fingerprints', of coal reflectance distributions (being expressed as the mean random reflectance of vitrinite). The volume proportions of the maceral groups are calculated from the histograms. The results obtained with the IBAS were generally in agreement with those obtained by conventional methods of reflectance measurement and point-count analysis. However, the results were inconsistent for coals with a bimodal character or a wide V-class distribution. The rank of the analysed coals ranged from 0,50 to 1,10 per cent mean random reflectance. The lowest reflectance that can be analysed with the IBAS is 0,4 per cent. The speed, objectiveness, and repeatability of this technique make it exceptionally suitable for use in the quality control of large numbers of samples.

Jan 1, 1990

By B. Valentim

Policies for reducing NOx emissions have led power plants to restrict O2, resulting in high-carbon fly ash production. Therefore, some potentially useful fly ash, such as the economizer fly ash, is discarded without a thorough knowledge of its composition. In order to characterize this type of fly ash, samples were collected from the economizer of a Portuguese power plant burning two low-sulfur bituminous coals. Characterization was also performed on economizer fly ash subsamples after wet sieving, density and magnetic separation. Analysis included atomic absorption spectroscopy, loss-on-ignition, scanning electron microscopy/energy-dispersive X-ray spectroscopy, optical microscopy, and micro-Raman spectroscopy. Key words: Fly ash; Petrology; Petrography; Economizer fly ash

Jan 1, 2009

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

By Cousens DR, Benhamou M, French DH

Techniques appropriate to petrographic image analysis are being developed using digitized backscatter electron images of well characterized mineral assemblages obtained from a Cameca scanning electron microprobe. Emphasis is on developing descriptors for size, shape and association of mineral grains as these all convey important information concerning the nature of rocks and the processes that have operated upon them. Processes, for example, that could indicate the proximity of mineralization. For convenience, the work is being carried out on the PDP11/73 host computer of the electron micropt be, although it is recongnized that such a multi-user environment is not appropriate for practical image analysis. The eventual aim is to develop a low-cost microcomputer-based package for quantitative description of mineral textures and rock fabrics as an objective aid to the petrographic analysis of ores and host rocks.

Jan 1, 1989

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

By Marion Rice

THE copper-mining district of Jerome, Ariz., is of such economic importance that the following brief notes may be of interest. The ore deposits are said by Ransome1 to be pre-Cambrian, and are contained in the pre-Cambrian schists of the region. In the vicinity of the mine (the United Verde) the schist stands nearly vertical .and strikes a little west of north. At least three varieties are distinguishable-(1) a green rock, schistose, on its margins but grading into massive material, which is evidently an altered dioritic intrusive; (2) a rough gray schist with abundant pheno-crysts of quartz, apparently an altered rhyolite; and (3) a satiny, greenish gray, very fissile sericitic schist that may be a metamorphosed sediment. The ore occurs in varieties (2) and (3), the main belt of dioritic rock (1) lying just west of the orebodies. The ore is said to follow as a rule the layers of fine sericitic schist. T. A. Rickard2 says that the ore at the United. Verde Extension mine is found at the contact of diorite and schist, that both diorite and ore are earlier than the regional metamorphism, and that the quartz porphyry (" rhyolite" of Ransome) is of post-Cambrian age.

Jan 9, 1918

By D. A. Lowrie

Environmental concerns and increasing mine development costs have created a need for early information on gold recovery from its host environment. The habit, association, and approximate abundance of minerals which contain unacceptable metallic ions which may be released during process of concentration of gold should be identified in exploration drill core. One case of a "clean" gold orebody is described to show that early petrographic studies contributed to a rapid decision to mine a small deposit by open pit and to custom mill the ore in an already restricted effluent environment. A second example describes identification of an undesirable mercury content and resulting action taken.

Jan 1, 1985

By A. N. Winchell

Petrographic studies of over 1400 rock and mineral samples, and studies of their field relations, show that there is a complete gradation between sandstone and limestone; the lime-silicate rocks were produced by recrystallization of limestone; mineralization and silicification occurred after silication and at considerably lower temperature; carbonation occurred at still lower temperatures. IN CONNECTION with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Bingham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance.

Jan 3, 1924

By Li Shibo, C. Halls

The compositions of olivine, pyroxene and chromite from the Proterozoic ultramafic complex are analagous to those of cumulate ultramafic rocks of tholeiitic origin, suggesting that the parent magma may have been tholeiitic rather than komatiitic. The complex contains economically significant Ni-Cu sulphide mineralisation. The high sulphide/silicate ratio is best explained in terms of the segregation of sulphides from a large volume of magma, of which all but the ultramafic cumulate fraction has since been eroded. Platinum-group minerals that have been identified include sperrylite, moncheite, native platinum, froodite, merenskyite, michenerite and Pd-rich pentlandite lamellae exsolved from pyrrhotite. They are characteristically found in close association with chalcopyrite, either along the contacts between hydrosilicate and sulphide grains or in cracks within pentlandite and chalcopyrite, which may also be intergrown with galena. Crystallisation from a Cu-rich residual magmatic liquid also enriched in Pt, Pd, As, Sb, Bi, Te, Zn and Pb is postulated.

Jan 12, 1993

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

By Walter Gaby

L. C. GRATON, Cambridge, Mass.-May I ask, in connection with one point in the summary, to what extent the author regards actinolite equivalent to tourmaline as an index of high-temperature and presumably magmatic conditions of deposition of the accompanying sulphides? W. E. GARY.-I merely advanced the idea that the mineral actinolite might have some such significance. In the copper deposit at Braden in South America, the ore occurs in an andesite breccia which is cemented by a matrix of sulphides, quartz, and tourmaline. Tourmaline is a high-temperature mineral, and when we find it associated with ores, these are regarded as having come from a volcanic or deep-seated source, hence a primary hypogenetic deposit. Thus we can count on greater continuation of the ore with depth than in some other kinds of deposit, and I thought that the actinolite, being also a high-temperature mineral, might have some such bearing in the case of Mount Morgan. I did not advance this idea as a final conclusion from a study of such phenomena, but thought that it might bear some discussion in view of the fact of the peculiar occurrence of this mineral in a notable orebody. It also occurs with the copper ores at Ducktown, Tenn., and in both cases may only be due to general regional metamorphism.

Jan 12, 1916

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By G. J. Jansen

Introduction Coal petrography is the microscopic study and description of coal and other organic substances in terms of the microscopically recognizable organic constituents and of the rank of the material. Petrography studies of coal and other organic substances are useful in themselves, and have a number of practical applications. Some of these include determining coking quality of coal, estimating yields of methane from coal beds, and assisting in coal preparation. Petrography studies can also help in mine planning, in source rock studies, in combustion problems, and in synthetic fuel applications. Most recently, petrography has been found to be useful in studying sediment-hosted ore deposits. Microscopic constituents-macerals Under the microscope, coal is a heterogeneous assemblage of the coalified remains of woody matter and plant remains from the swamp or bog from which the coal was formed. The individually recognizable materials making up the organic mass are termed macerals by petrographers. They are the organic equivalent of the minerals that make up rocks. Coal petrographers can examine coal in two ways. Those interested primarily in the microscopically transparent macerals or in the study of very low rank materials, lignites for examples, like to use transmitted light microscopy where light passes through a microsection about 3 to 6 µm (0.0001 to 0.0002 in.) thick (Fig. 1). The dominant red color of the section in Fig. 1 is inherent, not a stain or produced by a filter. Distinct suggestions of textures in the reddish constituents can be seen. The red material is vitrinite and is thought to be the coalified remains of woody tissues. The yellow, lenticular substance is exinite. It is what remains of the waxy coating on a spore. Also seen are white dots of mineral matter and black opaque material that is better seen and described in polished sections. A polished microsection is prepared by grinding and polishing to a mirror polish a compact of coal and embedding resin or a coherent chunk of coal. The resulting microsection is then examined in a reflecting microscope. High magnification, 200X to 400X, and an oil immersion lens are needed to resolve fully the macerals of the organic matter so prepared. Figure 2 shows two macerals, an even gray vitrinite, unstructured and fusinite, a whitish, more or less cellular constituent. Fusinite is thought to represent more or less completely carbonized cellular material. Coal petrographers appreciate that coal is a heterogeneous material. Figure 3 is a view of another section. The generally structureless gray material is vitrinite. The bean-shaped dark constituents are exinites. The long, narrow, somewhat scalloped dark constituent is cutinite. Cutinite is thought to be derived from leaf coatings. Some coal petrographers would describe the large white, structureless mass as micrinite. Others might prefer the term macrinite. A few fragments of fusinite can also be seen. Figure 4 shows a coalified fungal remain, termed sclerotinite. It is surrounded by vitrinite and crushed fragments of fusinite all floating in a sea of embedding resin. Sometimes the microscope reveals the great heterogeneity of coal even on the microscope scale. Figure 5 shows a section with semi-fusinite, inertodetritinite, vitrinite, and micrinite. The nature of the heterogeneity may be judged by noting that the long dimension of the photomicrograph is about 70 µm (0.0027 in.). Measurement of rank Hoffmann and Jenkner (1932) discovered that measuring the reflectance of the vitrinite constituent of coal in a polished section gave a good measurement of the rank of the coal. In practice, a photomultiplier is used to mea-

Jan 9, 1987

By Walter Miller

The remarkable strides which have been made in recent years in the art of petroleum refining are not fully apparent until we attempt to compare the scientific status of the industry today with the basic conditions existing a decade or so ago. The spotlight has played so strongly on the development of cracking that many of the wonderful steps brought about in other departments have crept upon us unawares. A number of causes have contributed to this highly accelerated rate of progress. Constant effort by both companies and individuals to obtain the honors and prizes rewarding new discoveries has played its usual important part in our industry as in others. Competition has applied its continuous pressure on the refiner to reduce costs and losses and increase the proportionate yields of the higher-valued fractions. Advances in the engineering professions and growth in chemistry and allied sciences have contributed much. But there are other factors which deserve particular mention. The rapid development of the internal combustion engine, with the rigorous quality requirements and large quantity consumption of both fuel and lubricants has been a tremendous influence in adding impetus to natural progress. The teaching of petroleum principles and practices in many of our best universities and technical schools, and the calling into the industry of ever greater numbers of scientifically trained men to supplement the efforts of the practically trained operators, as well as to apply at close hand the fundamentals of science as a life work, has had and is having an incalculable influence. Important Improvements Let us consider briefly some of the most important improvements: First, distillation, which constitutes the greatest single phase of refinery operations, even with cracking excluded; that phase of distillation being handled as an individual subject in this symposium. Today we are distilling crude oil and redistilling by-products at a rate very much faster than was possible with the lesser knowledge of the art which we possessed

Jan 1, 1927

By A. E. Wells

In this paper are described various comparative tests made on cracked and straight run gasolines. The results of these tests may be briefly summarized as follows: Samples of 54 to 55° Bé. gravity cracked gasolines, with end point of about 442° F., and with a somewhat larger proportion of the less volatile fractions than conformable to government specifications, were used in a single cylinder variable compression engine under the same conditions as were samples of straight run gasoline of 58 to 59° Bé. gravity, and of which one had a greater proportion of the more volatile fractions than called for in government specifications. The cracked gasolines showed decidedly less tendency to knock, hence could be used at higher compression ratios and thereby developed from 10 to 20 per cent. more power than did the straight run gasolines. These figures may be taken as one measure of the superiority of the cracked gasolines under test with the straight run gasolines. It is not claimed that all cracked gasolines are superior to all straight run gasolines to the extent indicated by the above tests; cracked gasolines vary as do the straight run products. Cross's work and that of others have indicated that certain cracked products may have a much greater superiority over straight run than that determined above. From various sources and by different methods of testing data are being obtained to show the definite and generally quite considerable superiority, as an anti-Cetonating fuel of cracked gasolines over straight run gasolines. It is now becoming generally recognized that by increasing the production of cracked gasoline motor fuel from those heavier petroleum fractions, which otherwise would be used for burning purposes, the petroleum industry is not only working in the interest of the conservation of the world's supply of petroleum, but is at the same time making available to the gasoline-consuming public a product distinctly superior to the straight run gasolines.

Jan 1, 1927

By Charles Parmelee

When Professor Silliman made his first examination of the newly-discovered Pennsylvania rock oil in 1859, he noted that different rates of heating produced different results in fractionation—longer heating produced larger percentages of light fractions. In 1862, it was found that when petroleum vapors are condensed in the still crown and dropped back into the hot liquid, the result of the distilling operation is materially modified. These early dates mark the beginning of what is called cracking petroleum and is explained as separating the component parts of the hydrocarbon molecules into more and smaller groups of the same elements. The phenomena were utilized for the next 30 years to increase the yield of burning oil. The procedure was that regularly practiced today in dry or destructive distillation. Considerable scientific study was given to the subject from 1862 to 1905, and a number of patents were obtained, but the work done was not continuous or intensive until about 1905, when the increasing demand for gasoline attracted attention of petroleum refiners to the possibilities of cracking. The first equipment built and operated essentially for cracking petroleum on a large scale was placed in successful operation in 1912. The commercial practice is, therefore, less than 15 years old. Comprehensive intense study of the controlling factors during this period has resulted in rapid increase in our knowledge, and material improvement has been made in the practice of the art. It is the purpose of this paper to outline briefly the state of our knowledge and to suggest some of the questions which are attracting attention of researchers at the present time. The major purposes for which petroleum hydrocarbons, including natural gas, are or have been cracked are: 1. To obtain products used to increase the heat value and illuminant content of artificial gas. 2. During the World War, to increase the supply of toluol. 3. To increase the amount of products capable of conversion into industrial chemicals. 4. To produce pure carbon.

Jan 1, 1927