Search Documents

T. R. HARRISON, Washington, D. C. (written discussion *).-Ad-vantage will be taken of this occasion to mention briefly a form of double potentiometer which has been used at the Bureau of Standards for about 2 1/2 yr. in calibrating thermocouples. The calibrations referred to are those made by comparison to standard couples. In order to insure equality of temperature between the couples, the junctions are fused together; consideration of fundamental principles will show that this introduces no error. Two separate potentiometers are used, one connected to each thermocouple, and each potentiometer is provided with a reflecting galvanometer. The two spots of light are reflected on to a single scale, the galvanometers being set in such a position that the spots coincide on the scale at a point marked zero when the circuits are open or when the potentiometers are balanced. By setting one potentiometer to a desired value and adjusting the other so that both spots pass across the scale together as the temperature rises or falls, simultaneous readings are obtained. By making observations first with a rising temperature and then with a falling temperature, the rates of rise and fall being approximately equal, and taking the means of the results found, several minor errors such as those clue to differences in the time lags of the two systems, etc., are eliminated or greatly reduced. The differences between the values

Jan 12, 1919

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By C J. Adams, H J. Campbell, T Popham, A Goodall

Pounamu is a MSori collective term for semi-precious stone scientifically referred to as nephrite, semi-nephrite, jade or bowenite (tangiwai) that is composed predominantly of metamorphic tremolite in a felted, fibrous texture. It is Aotearoa/New ZealandÆs icon mineral material. Ownership and management of this important taonga (treasure) has been vested in Te Rnnanga o NgSi Tahu as part of a Treaty of Waitangi settlement process. Increasing demand from the tourist, jewellery, fashion and sculpture industries, as well as cultural renaissance, has placed pressure on the pounamu resource. This had led to nephrite importation, allegations that foreign material is being marketed falsely as New Zealand pounamu, and wider concerns over the potential for exploitation/over-use and theft of genuine pounamu.   Research is underway to characterise different pounamu source regions by defining their ægenetic fingerprintÆ. The geological age and radiogenic isotopic composition of Aotearoa/New Zealand pounamu is distinguished from other nephrite jade occurrences overseas, due to relatively young cooling ages. Strontium isotope ratios distinguish pounamu from different source areas within Aotearoa/New Zealand (whakapapa), with signatures reflecting the host terrane rocks (their family) and their position in a sequence of metamorphic events (their generation). The research will provide a tool for archaeological research, trademark and resource protection.   Mineral resource assessments normally aim to define the total volume/tonnage present, which is generally assumed to be finite, applying drilling and geostatistical modelling. Pounamu resource assessment requires a different approach, as its intrinsic value is insufficient to warrant modern exploration methods (eg drilling, geophysics). Pounamu is only known to occur at a restricted few in-situ (hard-rock) localities. It is primarily found in transported (alluvial) detrital river and glacial outwash deposits, where collectable material has short term variability due to erosion and transport processes. A new methodology is being developed aiming to define: +        the total resource present, +        the relative rate of change in the availability of that resource through erosion and other geological processes, +        active areas where new material is likely to be exposed (eg by erosion), and +        appropriate extraction rates for sustainable use. The methodology will provide a holistic overview of the resource in different regions of Aotearoa/New Zealand, and may be applicable to other transient or restricted natural resources that occur within geologically active environments (eg supplies of driftwood on beaches).

Jan 1, 2005

By A McDowell

Pound Road Quarry is an alluvial gravel quarry owned and operated by Fulton Hogan Ltd. for the supply of aggregate in Canterbury, and is the largest quarry in the South Island in terms of production. It has evolved from three separate quarries, as a result of which extraction has occurred sporadically in a number of areas. Due to this factor, and the need to manage environmental impacts, a detailed quarry management plan was completed in 1995 which formed the basis for implementation of a certified environmental management system.   In December 1997, the quarry was the first in New Zealand to achieve ISO 14001 (TELARC) accreditation for implementation of an environmental management system. The main potential environmental impacts arising from the quarry operation include dust, noise and groundwater contamination, and visual landscape effects associated with gravel extraction, the mitigation of which is achieved by means of æbest practiceÆ methods. All quarry operations are controlled in terms of the environmental management system by means of regular (monthly and yearly) environmental reviews, appropriate auditing of environmental documents, and monitoring of environmental targets in accordance with consent and statutory requirements.

Jan 1, 1998

WHEN pouring concrete it frequently happens that space prohibits the placing of a mixer at the point, or points, where the concrete is to be used. Usually in such cases recourse is had to some form of pressure chamber, or concrete gun, to blow the mix by compressed air from the mixer to the point of pouring. Recently such a case arose at one of the western mines. The experience obtained there may be of benefit to others, not expert in the means of transporting mixed concrete, when they run up against similar situations. The first stage in pouring in this instance was a vertical drop of 100 ft. from the mixer on one level to the point where horizontal travel began on a lower level. Standard 6-in. pipe with flange joints was used, hung in the shaft space available. A standard 45" bend near the bottom directed the mix, with free discharge, into an air chamber for the horizontal stage of travel. With an air chamber at the mixer and pressure applied to the falling mix in the vertical section, jamming frequently occurred at the turn and the pipe would have to be taken apart for freeing. To obviate this difficulty the mix was poured slowly without the addition of air pressure, when it was found that the mix got through much better.

Jan 1, 1929

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By Shao Li, Chen Zhiming, Wu Jihong

In this paper,powder emulsion explosives,which have high sensitivity and strong detonation force,have been studied by applying emulsion technology to the production of the present powder ones.Under the condition of #8 industrial detonator initiation,the distance of air gap propagation is 110~180mm,brisance !3.5mm, lead block test value 325ml and detonation velocity 3000~4000m/s for small diameter (35mm) explosive cartridges.In addition to these,the factors effect on are investigated by experimental study and theoretical analysis.

Jan 1, 1991

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Douglas R. Burns

In New England, an area of the country where 3 ½" holes are considered large diameter,we are starting to experiment with 5" and 6" holes. The results are excellent in some areas and poor in others. The geology of rock is the major consideration to account for the blasting results.

Jan 1, 1997

By Frances H. Clark

DEVELOPMENTS in powder metallurgy have been disappointing in 1943. If any new part has gone into large-scale production, knowledge of it has been restricted by considerations of national security. Nor have any outstanding papers appeared to advance the theory of the subject during this period.

Jan 1, 1944

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By W. Rostoker

The process of diffusion alloying of mixed powders offers attractive possibilities both commercially and experimentally. It avoids the fabrication difficulties arising from high alloy contents. Indeed, the process is facilitated by larger alloy additions. The direct formation of the part or test piece and the opportunlity to perform machining operations under more favorable conditions are of no small importance. However, it is necessary to make only brief mention of the interesting features. As yet there have been few attempts to study this process in detail and to carry it to completion, if such is possible. It was intended not only to measure the intermediate and optimum magnetic properties of sintered alloys but to use magnetic testing itself as a means of following the progress of alloying under various condi-tions. Having established that alloys could be successfully synthesized by this tech. nique, the opportunity was taken to study the magnetic properties of several alloys of iron and silicon which had hitherto been too difficult to prepare in suitable test piece form. While avoiding some of the difficulties inherent in the fabrication of alloys by orthodox methods, the diffusion alloying process introduces a few of its own. The first of these is the evaluation of the approach to homogenization. In recent years some notable contributions have been made to this question, but considerable uncertainty remains in its definition and evaluation. This work has concerned itself with further study of this problem and it is hoped that more light has been shed on it. The second of these difficulties arises from the presence of porosity. It is inevitable that in the consolidation of a loose bulk of powder, there should remain some voids unless extremely high pressures are repeatedly applied. It was therefore of importance to investigate their effect on magnetic properties. Recently this effect has been studied and certain predictions made of its behavior. It is believed that the experimental results presented here provide a sound substantiation of the theoretical treatment. The attempt has been made to synthesize five alloys of the iron-silicon system and three each of the iron-nickel and iron-cobalt systems. A series of experiments was also conducted on some of these alloys to test their susceptibility to heat treatment. Some unfortunate experiences have provided opportunity to report data on the deleterious effects of nitrogen on magnetic properties when present as a a in protective atmospheres. MateRIALS, PREPARATION OF SAMPLES and Testing The purest materials available were em. ployed for this work. A specially purified,

Jan 1, 1949

By B. Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to he porous. In- deed, sponge iron, prepared by rcduction of the oxide in a reducing gas, is generally accepted as quite porous. with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig r shows commercial tungsten powder magni- fied at I0,000 X by the electron microscope,' both etched and unetched. In an earlier paper by one of the authors,* the existence of ports in tungsten powder was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these {pores} are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than IOO A. and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1949

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998

By Colin C. Harris, Jie Zheng, P. Sornasundaran

Powder surface and polymer structural changes during stirred milling have been studied as a function of grinding time, solid concentration and polymer molecular weight. It was found that specific surface area of limestone particles can be increased over 100% by using polymer additives. Particle surface and polymer structure were also found to change during grinding. Powder surface and polymer properties have been determined using Surface Tension, Fluorescence, TOC and HPLC/GPC analysis, and surface and polymer properties are correlated with operating variables and the mechanisms involved are explored. Particularly, the fragmentation of the polymer molecules was found to occur during long term grinding and this was beneficial for ultrafine grinding.

Jan 1, 1998

By E. H. Hamilton

WHEN starting a series of experiments on the use of powdered coal in lead blast furnaces to replace coke, I realized that in copper smelting the problem is simpler because the sulfur recovers the copper in the form of matte. In lead smelting there are greater difficulties because a reducing atmosphere must be maintained in the active, zone corresponding to each tuyere in order to get the best recovery of lead. Therefore, the feed of powdered coal must be quite regular, uniform and under control. The molten products issuing from the taphole are the resultant of the work of all the tuyeres and it can readily be con-ceived that one part of the furnace may be forming slag with a higher lead content than the slag formed in other parts of the furnace. At first, we used only one tuyere situated on the back of the furnace. This was for the purpose of getting all of our regulations under the regular operating conditions. We tried every known system of feed and found they were not dependable and our present system was finally worked out, and so far as we know, is the only working system that will give uniformly good saving in lead blast furnaces. We placed a Bristol self-recording thermometer on the feed floor. This gives a 24-hr. continuous record of the temperature of the gases leaving the furnace. We put a self-recording gage on the "15-lb." air used in the injector. A second recording Bristol gage was put on the low-pressure air (40 oz.). I realized that it was necessary that we should know the exact weight of coal going into each tuyere and that it should 'be under observation at all times. L. W. Kirk was assigned to the problem and developed the open sight feed and the distributor, so that we now have the coal being fed into each tuyere in sight of the men in charge. We have an apothecary's balance beside the furnace, and the operator takes the pan and inserts it under the stream of falling powdered coal for one minute, and places the pan on the scale, the other scale pan having weights indicating the desired amount to be fed to each tuyere per minute.

Jan 10, 1922

By A. W. Hahn

USE of gold leaf goes back to biblical and even to prehistoric times. Both gold and silver, as well as other metals, were employed in illustrating or illuminating manuscripts. The medieval monks also used bronze powders. Metals were subdivided as finely as possible by mechanical methods, or by granulation and then were pounded into finely divided flakes. Substances such as honey have also been employed, since early times to keep the flakes of metal apart during grinding. Stearic acid is a more modern agent used in flaking aluminum and other metals. Finely divided "blue powder" is a by-product in retorting zinc ores, and contains from 78 to 90 per cent of zinc metal. This has been used as a precipitant for precious metals in the cyanide process and for chemical reduction processes. The making of zinc dust by atomizing is a step well known in electrolytic zinc plants. The Thermit process of Goldschmidt also requires the use of finely divided aluminum.

Jan 1, 1937