Search Documents

By Shulin Nie

The detonability of a chemically gassed emulsion explosive has been studied in recent tests, after the study of three micro-balloon sensitized emulsion explosives. Blasting experiments in steel pipes and computer simulation have been carried out. This study showed that the gassed emulsion explosive and the micro-balloon sensitized emulsion explosives have different desensitization features. Namely, the gassed emulsion explosive can recover its detonability very rapidly after the pressure vanishes, in contrary to the micro-balloon sensitized explosives.

Jan 1, 1997

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980

By Frank Miller

THE lower cost of producing oil from naturally flowing wells compared with pro-duction costs accruing from artificial lifting methods has stimulated much research, with the joint purpose of extending the natural flowing life of wells and of increas-ing the productivity of small wells. The laboratory investigation described herein was made to determine the effect of a slotted liner on the pressure gradient in the vicinity of the wall of a flowing well. Flow restrictions caused by the liner induce energy losses between the oil-bearing for-mation and the inside of the liner, which may be reduced by improved liner design, and thereby the flow capacity of wells may be increased. These losses have been evalu-ated for rectangular slots of different sizes, and means are suggested for reducing them. The dearth of information concerning the nature of the flow of fluids from uncon-solidated sands through small openings in the walls of pipes-as represented by the flow of oil from an oil sand into a slotted liner-is acknowledged. Although the bene-fits to be realized by operators through the use of optimum liners is just beginning to be recognized generally, Coberly1 in 1937 pointed out that the functioning of screen casing is an important factor in the pro-duction of oil. From his study on the selection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string de-serves continued study, especially with respect to the selection of perforations. The growing use of gravel packing result-ing from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded.

Jan 1, 1940

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By Aaron Miles

THE pressure distribution in a producing oil or gas reservoir has been obtained mathematically in a limited number of special cases where the boundary of the reservoirs are simple geometric figures with the wells conveniently located within them. Using some of the previous work as a basis, it can be proved that a number of additional problems of pressure distribution can be solved by use of soap film. This method is particu-larly applicable to a reservoir drained by a number of wells, or to a reservoir of irregular shape, or to both. Since this method obtains the pressure distribution, it also establishes the drainage boundaries of the wells. This paper derives the analogy between the equation representing the pressure distribution in a reservoir and the equation of the deflected membrane. It also describes the apparatus and the method of operation. The experimental method is employed to solve a problem whose mathe-matical solution is known and the results compared. These are found to be in good agreement. The method is applicable to any homogeneous liquid, compressible or incompressible, or to a gas, flowing in a reservoir of uniform thickness, permeability and porosity. The flow state may be either the steady state or the transient state wherein the density or pressure of the fluid in the reservoir declines at a constant rate.

Jan 1, 1938

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By Gray N. B, Floyd J. M

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By R Deshaise, B Mbhanty

The importance of controlling density of commercial explosives, and the various means to achieve it are described. m e field conditions responsible for density changes during blasting and their effect on blast results are examined. Understanding of the behaviour of density control ingredients such as gas bubbles, glass and plastic microballoons under pressure, is considered essential to predicting explosives performance. Both static and dynamic pressure effects have been studied for typical donor-receptor cartridge configurations. The amplitude and temporal characteristics of dynamic pressures inside receptor explosives have been studied by means of the underwater test, and guidelines developed to limit density changes due to external pressures.

Jan 1, 1989

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By Francis R. S, Campbell J. J

Aberfoyle's Hellyer Division has filtered very fine flotation concentrates using two different makes of pressure filter. At the Luina concentrator a Larox pressure filter was used to treat a combined Pb + Zn or bulk concentrate. At the Hellyer concentrator two Lasta pressure filters are being used to filter copper/silver, lead, zinc and bulk concentrates. Operating parameters and performance at both operations are described. In both concentrators it was found that correct cloth selection was critical and that cloth failures contributed significantly to downtime. Thorough preventative maintenance progammes were required to ensure adequate availability of both makes of filter.

Jan 1, 1989

Extensive reserves of kaolin of the type suitable for use as a high quality paper coating exist on the Weipa Peninsula. In 1986 a commercial processing plant was constructed to produce 100 000 tonnes per annum of coating quality kaolin targetted principally for export. A number of processing difficulties have limited the production capability of the plant. The prime area being the pressure filtration operation with achieved cycle times being around 50-60% of design. The rate determining steps being press filling, press unloading and filter cloth washing. This paper details and summarises testwork and results from our attempts at decreasing the filtration cycle time.

Jan 1, 1989

By A. V. Quine

FOUR years ago several mining operators shook their heads and predicted that Goldfield Consolidated Mines Co. would never be able to mine the zinc-lead ores from the 550 to 650 level areas of the Deep Creek mine. Their prediction was not without apparent justification, for everywhere one gazed, water was spurting or dripping; every hole that was drilled produced more and more water under pressures of 220 to 250 psi, all from apparently unrelated channels. When the volume of water from one level alone reached 2200 gpm with a possible flow of 5000 to 6000 gpm if the area were fully tapped, development work was brought to a halt and the few holes into the water area were grouted off under contract. As zinc prices had completely deteriorated, the workings were allowed to flood. Upon reopening the mine, in late 1950, it was discovered that the relatively few sacks of cement used in the previous grouting operation had done a tremendous amount of good. Consequently it was decided to systematically drill test holes with a longhole machine and diamond drill and to seal all holes with a cement grout solution. After 30,000 ft of drilling, and the pumping of over 20,000 sacks of cement, 15,000 of which were placed in the supposedly impossible 650 level, the company was successful in literally forcing the water out of the ore zones and opening up large tonnages for subsequent extraction.

Jan 3, 1954

By Peter G. Mason

Over the last 15 years numerous Pressure Oxidation and Pressure Leach plants have been installed throughout the world. The technology is no longer regarded with awe and trepidation as plants designed to treat a wide range of feedstocks continue to be successfully brought on line. Important aspects of the design of such plants include feed preparation, slurry pumping, heating and heat recovery, pressure control and let-down, vessel design, safety and provision of associated services.

Jan 1, 1999

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008