Search Documents

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By C. Droun

"Low back pains account for about 13 per cent of all compensation claims made to the Quebec Workmen's Compensation Commission and cost the employers a sum exceeding ten million dollars. The frequency and cost of these health problems in Quebec metal mines are proportional to the provincial trends. An elaborate review of the literature on the causes, nature and prevention of low back pain is made in this presentation. A prevention program for low back pain has been designed in cooperation with a team of seven medical specialists and two physiotherapists for the Quebec metal mines. The program is especially designed for persons who have had low back pain, in order to prevent a recurrence, and for persons beginning to feel chronic difficulties. It is based on existing programs at the Hawthorne Plant of Western Electric Company and at Minnesota Mining and Manufacturing, but it requires a much different approach because of the nature of medical care available at the mining sites. The program is difficult because it involves a change of attitude for every employee and every supervisor. The program, so far, is beneficial because several men are now seriously engaged in an active program of reconditioning and because the problem of low back pain ie beginning to be seen from a new angle."

Jan 1, 1973

By D. C. Van Aken, O. J. Rajtora

A research effort sponsored by the Department of Energy (DOE) and several steel producers, is investigating the benefits of coating steelcasting nozzles with various materials. Coatings were applied to casting simulation nozzles made from industrial tundish nozzles (primarily of magnesia) and industrial submerged entry nozzles (SEN's) (primarily of alumina-graphite) in order to extend casting time prior to nozzle clogging. Nozzles were coated by air plasma spray (APS) using a 9M series APS system from Sulzer-Metco. The ability of these coatings to provide protection from clogging was evaluated using a steel casting simulation. Substrate-coating compatibility was characterized using optical and SEM microscopy.

Jan 1, 2004

By G. L. Spence

Prevention of cuprous and cupric oxide formation on stored ETP copper rod is a major concern for copper rod and wire producers. During normal storage periods copper oxide layers can increase from less then 100 A to more then 1000 A exceeding ASTM specifications and discoloring the rod surface. Various types of corrosion inhibitors are tested and compared in effectiveness for prevention of copper oxide formation on stored copper rod. Aromatic triazole compounds are also compared to a non-azole containing compound.

Jan 1, 2007

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

Scale build-up in titanium palladium alloy spent electrolyte heat exchangers in the residue treatment plant commissioned at Risdon, Tasmania in 1971 was shown to be a mixture of manganese dioxide and anhydrite (CaSO4). The manganese dioxide was deposited as a result of thermal decomposition of permanganate ions present in the spent electrolyte. It was shown that deposition of manganese dioxide and associated anhydrite scale could be prevented by prior reduction of permanganate ions to the manganous (Mn++) state by the addition of ferrous ions. In the plant this was conveniently accomplished by injecting into the inlet line to the heat exchangers sufficient zinc plant solution containing ferrous sulfate to decolourise the spent electrolyte. This action prevented deposition of such scale for another 21 years, until the heaters were finally decommissioned in March 1992. Measurements indicated that addition of the reducing solution lowered the anodic potential of the titanium alloy by 200 - 300 mV (depending on the solution resistance), but that it was still +300 to 400 mV with respect to a standard calomel electrode. It was shown that, if necessary, a small impressed current could be applied to provide anodic protection. Before scale deposition was overcome by the addition of ferrous sulfate solution, badly scaled heat exchangers were cleaned by recirculating a solution of hydrogen peroxide in spent electrolyte or dilute aqueous sulfuric acid, after laboratory testing of a variety of possible solvents for the scale. Corrosion tests indicated that attack on the titanium alloy by the acidic peroxide cleaning solution was insignificant.

Jan 1, 2005

By G. Van Weert

Refractory ores and concentrates containing silver tend to form Ag-jarosite during autoclave oxidation. Silver extraction from the oxidation products is therefore low, unless a hot lime treatment step to decompose Ag-jarosite precedes cyanidation. Since silver iodide is very stable but soluble in cyanide solutions, the formation and decomposition of Ag-jarosite in the presence of iodine species was studied. Results indicate that Ag-jarosite formation could be prevented in favour of H3O-jarosite and AgI while oxidizing Ag2S under industrial autoclaving conditions, when the total iodine species to Ag mole ratio exceeded 5. Lower ratios gave proportionally more Ag-jarosite and less AgI. Under these conditions existing Ag-jarosite was also found to decompose in H30-jarosite and AgI.

Jan 1, 1993

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Henry Howe

THAT the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First; each particle of any composite liquid, whether it be an aqueous solution or a molten metal; in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the, existing temperature, - and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already, solidified; A, Fig. 1. The other part is, fusible at the existing temperature and hence remains molten. In the case of carbon Open steel, the part. of each drop which actually j; Sea solidifies is poorer, in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying,. half-drop enriches . the other, half-drop in carbon, and Layer of Liquid thus. makes it unfreezable at the existing tem- Fig. 1.MECHANISM OF perature. SOLIDIFICATION. By this- mechanism there arises during solidification a " littoral" or shore layer- of liquid, B, Fig. 1, bathing the already solidified. walls, and more fusible than either those walls or the great remaining central mass of liquid or "deep sea," C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile. heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal

Jan 2, 1919

By Lu Jiam Zhang

Coal and gas outburst is one of the serious natural disasters in the coal mines of China. Since 1950, more than 10,000 coal or gas outbursts have occurred in more than 200 underground coal mines of different types. The outburst prone coal mines are widely spread out. It occurs in different types of coal -ma and is very serious in some areas. Most outbursts occurred at the time of roadway driving in coal seam, serious outbursts occurred mainly when entering the coal seam during the cross-cut driving; of the outbursts, coal and gas outbursts We UP major proportion, while pressing out and pouring out ah account for a large proportion; outburst. occur under different operating conditions, but mostly occur during shotfiring. This paper introduces the prevention and control measures as practiced in China and illustrates the three types of outburst cla8sification. Both technology and management are equally important in outburst prevention and control. Measurement of the volume of drilling cuttings and the initial gas outflow rate fm- boreholes have proven to be effective. A special team and organization must be set up to deal with the problems.

Jan 1, 1987

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By Arthur L. Hawthorne

10.1-1. Relative Position of Maintenance as Compared to the Overall Mining Costs. The basic issue regarding the importance of maintenance in the modern mining industry must be faced squarely by the top manage- ment of each company before any real progress can be made in organizing a maintenance program for optimum effectiveness. Just a few decades ago the maintenance at coal mines consisted primarily of a blacksmith for sharpening picks and shoeing mules; as a result, probably less than 5%of the total mining cost went to maintenance and some 80% was operating expenses (operating labor). With each succeeding advance in equipment design towards larger, more complex, and more productive units, the pendu- lum swings the other way. As an example, haulage trucks have progressed through various stages in the past 20 years from 15-ton units to a 240-ton truck now in the "shakedown" or experimental stage. The following com- parison between 15-ton, 50-ton, and 100-ton haulage trucks clearly illus- trates this changing cost pattern in terms of percent of overall costs for running each size unit. [Maintenance 24% 44 % 51 % Operating labor 59 % 33 % 16% Operating supplies (fuel oil) 4 %. 4% 3% Labor burden and vac. pay 6 % 4% 3% Depreciation Total] From the preceding figures it is interesting to note that, as a rule, operat- ing costs go down as the equipment gets larger and the maintenance costs increase with the larger units. This same trend in cost variation applies to nearly all mechanical equipment used in surface mining from the large

Jan 1, 1968

By J. B. Novak

The program describes preventive maintenance practices and controls applicable in situations where maintenance actions are triggered primarily by breakdown or part failure and specification and documentation of detailed maintenance practices are minimal or nonexistent. The presentation describes requirements of organization structure, program administration, implementation and operation, type of benefits expected, and actual benefits derived in selected areas. The principle objectives of the program are to provide quick, inexpensive, and effective controls over maintenance practices and requirements and to establish a nucleus of controls that subsequently can be expanded to cover all maintenance activities.

Jan 1, 1973

By Joseph B. Novak

In the last decade or so, the importance of effective preventive maintenance controls and practices has taken on a new and accelerated emphasis. Advances in technology and changes in equipment and product designs impose more precise and demanding standards of quality, productivity and customer service at a very rapid pace. Daily, it is becoming more apparent that in order to fulfill current requirements, existing manufacturing practices and associated control programs must also be upgraded and expanded. This is particularly true in the field of maintenance services. As production and quality standards become more demanding, effective equipment maintenance takes on more importance and becomes more difficult to sustain. In modern plants, the failure of a single equipment component can shutdown a complete production line causing interruptions to operating and shipping schedules that result in costly downtime, dissatisfied customers, and reduced profits. These costly experiences can be minimized with an effective maintenance program that provides maximum equipment reliability and minimum downtime and readily adapts to revision and change. A significant feature of an effective program is the provision of controls over activities generally identified as

Jan 1, 1971

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

By Charles H. McGuirk

The Port of Conneaut, the largest bulk material handling and storage facility on the Great Lakes, is using the latest electronic and visual testing devices to augment and enhance its well established computerized preventive maintenance system. The results of this comprehensive program have been impressive. The remaining life of components can be accurately forcast, and replacement can be programmed around operations, resulting in a significant improvement in system availability and reduced costs for the dock operator and its customers.

Jan 1, 1983

By S. Yerel

In a mineral processing plant, the determination of a preventive maintenance schedule is one of the most important maintenance policies. In this study, to determine the preventive maintenance schedule for the Emet Colemanite Mineral Processing Plant in Turkey, a mean quality control chart was constructed using the historical concentrate B2O3 grade data. The effect of preventive maintenance scheduling on B2O3 grades was monitored using the mean quality control chart. It was determined that recovery increased after each preventive maintenance scheduling. Close examination of the mean quality control charts indicated that there were three periods that showed different grade characteristics. These were identified as the period ?prior to preventive maintenance,? the period ?after preventive maintenance? and the period ?requiring preventive maintenance.? These periods were compared as two independent samples by using the Kolmogorov-Smirnov test. Application of this test for interpretation of the mean quality control chart enabled the authors to analyze the system effectively, and it showed that the preventive maintenance for this plant should be scheduled at four-month intervals.

Jan 1, 2007

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022