Search Documents

By A. R. Rule

Research was done by the Bureau of Mines to determine the effect of a low-molecular-weight polymer on wet grinding of quartz, dolomite, and a copper ore. A 5-in ball mill equipped with a torque sensor for precise measurement of input energy was used for batch grinding tests. Grinding parameters were determined from size distribution data on the feed material and ground product. Zeta potential measurements were made to determine the effect of the polymer on the surface properties of the three materials, and a viscometer was used to measure the effect of the polymer on slurry viscosity. The addition of the polymer caused a sharp increase in the negative value of the zeta potential for all three materials, indicating that pronounced adsorption was taking place. At a constant slurry percent solids, addition of the polymer caused a similar reduction in slurry viscosity for each material. For quartz, dolomite, and the copper ore, grinding efficiency, as measured by kilogram of product per kilowatt hour passing a given screen size, was not affected by the addition of the polymer. However, the lowering in slurry viscosity caused by addi-tion of the polymer permits grinding at a higher slurry percent solids.

Jan 1, 1985

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By R. H. Lien

The Bureau of Mines investigated a roast-leach process for recovering a marketable lithium product from a montmorillonite-type clay deposit located on the Nevada-Oregon border. The clay sample treated in the investigation contained 0.6 wt pct Li. The lithium recovery process consisted of several unit operations. The lithium silicate compounds in the clay were converted to Li2SO4 by roasting a pelletized mixture of clay, limestone, and gypsum at 900° C in a direct-gas-fired rotary roaster. Water--leaching the calcine at 40 pct solids extracted the Li2SO4. Lithium recovery from the leach solution involved concentrating the solution by evaporation, adding Na2CO3 to the concentrated solution to precipitate Li2CO3 , and filtering the slurry to obtain the product. The product filtrate was recycled to the evaporator following a crystallization step. About 80 pct of the lithium in the clay was recovered as 99-pct-pure Li2CO3. Process operating costs were estimated at $2.12/lb Li2CO3 produced; the current Li2CO3 selling price is $1.48/lb. Raw materials. accounted for 30 pct of the total operating cost.

Jan 1, 1985

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By Michael J. Beus

This Bureau of Mines report describes a field experiment involving the sinking of two test shafts to directly compare the deformational behavior of circular and rectangular shapes. Results show that the circular shape is less sensitive to geologic discontinuities and applied stress field. Also, the rectangular shape is subject to a variety of behavioral modes, including beam bending and buckling. Geologic discontinuities around circular and rectangular shapes influence displacement significantly. Simple, two-dimensional elastic finite-element modeling, simulating circular and rectangular shapes in a biaxial stress field, shows that the structural response of a shaft is largely controlled by geologic structure. Consideration of anisotropy may be required for realistic analysis of a deep shaft.

Jan 1, 1985

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

The objectives of this research were to examine and to laboratory performance of several brands of rigid urethane een brands, produced by 13 manufacturers, were examined. was performed in a laboratory under controlled conditions. document the foam. Eight-All testing Preliminary laboratory tests included flame spread evaluations, flame penetration, ignition temperatures, air permeability, and adhesion. Having established arbitrary cutoff values, the original 18 candidates were narrowed to 8. More specialized tests followed. The effects of water immersion and dry aging on flame spread performance and other physical properties were then examined. This Bureau of Mines report was written to provide information for those concerned with using rigid urethane foam as a sealant. Its intent is to describe the various laboratory evaluations performed and to delineate the performance of each candidate. This report neither promotes nor discourages the use of rigid urethane foams. It presents results that will enable those responsible for using or enforcing the use of rigid urethane foams in underground mines to make informed decisions.

Jan 1, 1985

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985

By Gary L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from low-grade domestic chromites, which contain silicon and aluminum impurity levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten sodium hydroxide (NaOH) under oxidizing conditions to form sodium chromate (Na2Cr04). The reaction product is leached with methanol to remove the majority of the unreacted sodium hydroxide, then with water to remove the sodium chromate and the remainder of the sodium hydroxide. The sodium chromate product is recovered by evaporative crystallization from the aqueous solution. This report presents results of laboratory tests to determine the optimum fusion conditions and the chromium extractions obtained from several domestic chrotdte concentrates. These concentrates are from a variety of sources, including the Stillwater Complex in Montana, Kanuti River-Caribou Mountain, Red Bluff Bay, Kenai Peninsula, and Kodiak Island areas in Alaska, deposits in northern California, and a nickel-cobalt laterite from southern Oregon. All of these concentrates were successfully treated by the Bureau procedure. The best chromium extrac-tions obtained for each of these materials ranged from 69.5 to 98.9 pet.

Jan 1, 1985

By D. L. Sawyer

The Bureau of Mines studied alumina extraction from uncalcined, kao-linitic clay at temperatures from 1000 to 2500 C using 20-or 27-wt-pct-HCI concentrations and with an acid-to-clay ratio of from 0.8 to 1.4 times stoichiometric. Autogenous digestion pressures ranged from atmospheric pressure to about 900 psia. Extraction of 96 pct of the alumina was obtained by HCI leaching at temperatures and leaching times that varied from 1000 C for 120 h to 2000 C for 15 min. Hydrochloric acid stoichiometry of the reaction A1203&apos;2Si02&apos;2H20 + 6HCI + 2AICl3 + 2Si02 + 5H20 was studied at different temperatures and leaching times in a 750-mL tetrafluoroethylene-polymer-lined autoclave. A combination of high temperature and 20 wt pct excess HCI promoted rapid and almost quantitative extraction of alumina (99 pct in some tests). Additional Bureau data obtained with 35-mL tantalum bombs and leach-ing tests with added fluoride are also provided. At high temperatures, the addition of fluoride did not result in a significant improvement over HCI alone and was deleterious to the filtering properties of the digest residue.

Jan 1, 1985

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By D. G. Collins

As part of its effort to develop ways to maximize resource recovery, the Bureau of Mines investigated the extraction of vanadium from Western phosphate beneficiation tailings with H2S04 and/or H3P04. Dissolution of the vanadium was accomplished by digesting a mixture of acid and a 50-pet-solids, tailings-water slurry. In the most effective method investigated, vanadium and phosphorus were leached by digesting the slurry at a constant boiling temperature (1000-1100 C) in a stirred reactor. In batch tests, maximum vanadium dissolution was 95 pet. In continuous-circuit tests designed to further evaluate vanadium dissolution at con-stant boiling temperature in a continuously stirred reactor, vanadium dissolution ranged from 70 to 85 pet. An economic evaluation of the process demonstrated that H2S04 consumption is the major cost factor. Based on the value of the vanadium product with no allowance for a phos-phate product, the cost of producing the V205 is more than twice its value. The potential for profit would depend upon the value of the phosphate fertilizer produced from the impure H3P04 remaining after vanadium extraction.

Jan 1, 1985

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine&apos;s ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985