Search Documents

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By W. M. Rutherford

A knowledge of the limits of miscibility between reservoir oil and possible injection fluids is required for selection of the optimum miscible-injection fluid. Limits of miscibility can be estimated from the results of equilibrium phase-behavior experiments. They can also be determined by means of displacement experiments conducted in a high-pressure sandpack. This paper describes the equipment and procedure which have been developed for determining miscibility conditions by stable displacement. A systematic series of displacements of a West Texas reservoir oil was carried out. The results indicate that, at constant pressure, miscibility is a function only of the pseudocritical temperature of the injection gas. This fact, together with improved experimental methods, makes the displacement technique a rapid, reliable means for determining miscibility conditions. In conjunction with the displacement experiments, phase diagrams were constructed for the oil with dry gas and propane and with dry gas and ethane. Phase behavior of the methane-ethane-propane system was determined at 110°F. The experimental work demonstrates the feasibility of using ethane-rich gases to reduce cost and pressure requirements for miscible displacement. INTRODUCTION In recent years, interest in the miscible displacement of oil by light hydrocarbon mixtures has been high. Many pilot and a few field scale projects have been started.1 These projects have made use of various methods for achieving miscibility: (1) the LPG-slug process, (2) the enriched-gas-drive process and (3) the high-pressure gas-drive process. Some field projects have been successful; the results of others are debatable. In general, projects which have performed best have involved the injection of an appreciable fraction of a pore volume of miscible material. Economical application of miscible displacement depends strongly on the cost of the miscible-injection fluid. If an appreciable fraction of a pore volume of material is required for successful application of these methods, a precise knowledge of the minimum requirements for miscibility in terms of composition of injection fluid is essential. Therefore, reliable experimental methods for determining miscibility conditions are important, and a procedure for estimating these conditions from the composition of the reservoir fluid is highly desirable. The subject of this paper is the problem of determining conditions which result in miscible displacement of oil by light hydrocarbon mixtures. Miscibility conditions can be estimated by means of equilibrium experiments conducted in a PVT cell, or they can be determined by means of high-pressure displacement experiments. This paper describes the equipment and procedure which have been developed for the determination of miscibility by high-pressure displacement experiments. These methods have been applied to the displacement of a West Texas reservoir oil with mixtures of dry gas, ethane and propane. In conjunction with the displacement experiments, triangular phase diagrams have been constructed for mixtures of the oil with dry gas and propane and with dry gas and ethane. The effect of injection-gas composition on conditions for miscible displacement in high-pressure sandpacks and cores has been the subject of several published papers.2-5 The experimental methods used in these investigations were such that displacements were unstable, and the effects of fingering and/or gravity layover are clearly evident in the results. Miscibility conditions were probably correct in spite of the instability phenomena, but the experiments evidently were time-consuming, and limited data were reported. Systematic high-pressure flow studies which would support a correlation of miscibility conditions have not been reported; however, Wilson5 has proposed the use of pseudocritical temperature of the injection gas as a parameter and Benham, et al,6 have based a miscibility correlation on observed and calculated equilibrium data.

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By H. H. Rachford, D. W. Peaceman

A system of partial differential equations describing miscible displacement of fluids in porous media is derived The system takes into account the influence of gravity, the spatial distribution of permeability, diffusion, and fluid viscosities and densities. A numerical procedure for approximating solutions to the differential systems has been tested for a horizontal two-dimensional geometry. In end-to-end displacements of oil with less-viscous solvents, the numerical solutions exhibited fingering qualitatively similar to that observed in laboratory models. Small random spatial variations in permeability about the mean value are sufficient to initiate fingering. Quantitative comparisons of computed results with laboratory data show good agreement. INTRODUCTION Miscible flooding of oil by solvent is receiving increasing consideration for field use.1-4 Unfortunately, such floods potentially present severe problems in loss of recovery through the by-passing of oil by expensive solvent. Consequently, their economic evaluation requires sound techniques for predicting recovery. The purposes of this work are to present a finite-difference method for calculating the multidimensional displacement of oil by solvent and to investigate the validity of the method by comparing results of calculations with data from displacements in laboratory models.5 The formulation of the method to simulate the model experiments treats a case of limited scope in the description of solvent flooding in the reservoir. The model experiments were carried out with fluids that were assumed to form an incompressible, ideal, two-component system with constant diffusivity. Establishing the validity of the method even in its present form provides a major step toward the goal of quantitatively evaluating individual solvent flooding projects. First, it demonstrates the fea- sibility of calculating the course of displacements which are dominated by an inherent macroscopic instability, i.e., viscous fingering. In addition, the method provides almost the only practical means of examining the effect of the size and extent of reservoir inhomogeneities on the development and propagation of the fingers, taking into account the important influences of diffusion and gravitational segregation. It might be inferred that such studies cannot yield results of practical value because in displacements dominated by macroscopic instability the pattern of finger development and the resulting performance should depend critically on small variations in the geometric distribution of reservoir inhomogeneities. The present method offers the capability inherent in computational techniques of predicting performance reproducibly with any arbitrary distribution of reservoir properties and, as such, provides a means of evaluating the sensitivity of behavior to uncertainties in reservoir definition and, thus, assessing the reliability of prediction of performance. THE PHYSICAL PROBLEM DATA USED FOR QUANTITATIVE TESTS OF CALCULATIONS In this work, a calculation for treating the miscible-displacement process is tested by comparing calculated results with experimental data. The experiments chosen for comparison have been described in detail,5 and the quantitative features are summarized in a later section. Briefly, oil was flooded by solvent of equal density from a thin rectangular channel in Lucite packed with uniform Ottawa sand. Under these conditions, two-dimensional geometry is considered adequate to represent the process. Inasmuch as the present work is concerned with testing of the method by comparison with specific two-dimensional data, the system of equations presented in the succeeding section will be oriented to defining the physical system specifically. THE DIFFERENTIAL EQUATIONS Suppose x, y to be a Cartesian co-ordinate system and define h(x, y) to be the height of a point above a horizontal reference plane. It will be assumed

By B. H. Caudle, L. G. Loncarie

Pilot flooding is one method of evaluating a proposed secondary recovery project. However, the amount and rate of oil recovery from an unconfined pilot area is not usually the same as from an equal area in a large-scale flood. This is true because fluids are free to move across the boundary of a pilot area. The result is that some of the oil produced in a pilot flood may come from outside the designated area and some of the displaced oil may leave the pilot area completely. This paper presents the results of fluid-flow model studies on a five-spot pilot flood. Mobility ratios between 0.1 and to have been studied. The effects of changing the ratio of injection to withdrawal rates are shown. INTRODUCTION A small-scale field test, or pilot flood, is an accepted method for evaluating the applicability of a secondary recovery operation and the economic potential of that operation for a reservoir. The pilot flood is carried on in the same manner, with the same injected materials and at the same pressures as would be used were the secondary recovery program to be expanded to a larger area of the field or to the entire field. If the reservoir fluid and reservoir rock properties are the same in the pilot area as in the rest of the reservoir, the production, injection and other pertinent data associated with the pilot test will represent and measure what should be expected from a full-scale development of this secondary recovery program. There is one major exception which, unfortunately, has been overlooked by many and which has been awaiting quantitative definition. This is the sweep-out pattern the reservoir engineer must use in interpreting the pilot flood and in extrapolating it to the full-scale development. The sweep-out area in a pilot flood is not contained within the five-spot pattern. Further, there is oil flow into and/or out of the five-spot during a pilot test. Thus, production data from pilots must be interpreted with this different flow system and sweep pattern in mind. We have studied the sweep-out pattern that will exist for some conditions of operation of pilot flooding a single five-spot (four injection wells and one producer). In our study, reported here, we have assumed that the reservoir is relatively homogeneous and of uniform thickness in the pilot area. The results of this study en-able the engineer to predict the recovery, injection requirements and project life for a full-scale operation from the pilot flooding data. The effects of various injection to withdrawal-rate ratios and mobility ratios in a relatively gas-free (10 per cent pore volume or less) system are shown. Experimental Method The technique used in this study was the same as that for the X-ray shadowgraph studies of sweep-out pattern efficiencies.' The model of the pilot and surrounding area was made from a uniform packing of round-grain sand consolidated with an epoxy resin. Fig. 1 shows the relation between the model and the pilot area. Only one-eighth of the pilot area had to be represented in the model because we assumed equal injec-

By C. C. Templeton, J. C. Rodgers

A key step in feed water treatment for generating wet steam for thermal oil recovery is the removal of calcium and magnesiunt hardness by cation-exchange series softening. Knowing the solubility of any scale forming salts in brines at elevated temperatures is necessary for fixing the level to which the feed water must be softened. Such calcium sulfate solubility data, previously not available above 392F, were determined by the authors in a flow equilibrium apparatus mud will be reported elsewhere. These data were used to develop a method for predicting the solubility of anhydrite in hot water or steam droplets for saturated steam pressures as high as 2,000 psig (637F). (The calcium sulfate solubility product is represented by a combination of two factors, one reflecting the effects of ionic strength and the other accounting for the effects of complex ion formation in either calcium-magnesium-rich or sulfate-rich brines.) The method is applied to a calcium-magnesium-rich brine If moderately high salinity from a pilot hot-water flood, I nd to several sulfate-rich, low-salinity feed waters and l lowdown (cooled steam droplets) samples from steam s ak operations. The predicted calcium hardness levels corresponding to the calcium sulfate solubilities agreed reasonably well with the results of laboratory solubility determinations run on the field samples. Further testing of the method is needed for brines of other composition classes. Existing field cation exchange softeners in the cases tested are performing adequately since all the samples were found to be undersaturated with respect to calcium sulfate at their operating temperatures. Introduction Prevention of scaling caused by precipitation of calcium sulfate (anhydrite) is of considerable concern in connection with thermal recovery processes using wet steam or hot water. To avoid anhydrite precipitation in a heated system, an engineer must keep the product of the calcium and sulfate concentrations in the water or steam droplets below the value of the solubility product of anhydrite for the temperature and brine composition in question. Usually it is most practical to keep the concentration product lower than the solubility product by keeping calcium low in the presence of high sulfate, or by keeping sulfate low in the presence of high calcium. This can be done by a choice of combinations of natural waters and water treatment processes (such as series cation exchange softening to remove calcium). Until recently, few anhydrite solubility data, particularly for solutions containing other salts, were available for temperatures above 392F (211 psig steam); Marshall, Slusher and Jones' studied the CaS0,-NaCI-H,O system up to 392F and surveyed the work of previous investigators. To model natural brines, one needs to study the solubility of anhydrite in aqueous solutions of sodium chloride, sodium sulfate, calcium chloride, magnesium chloride and their mixtures. Since steam pressures as high as 2,000 psig (637F) may be involved in thermal oil recovery projects, a solubility study was conducted between 482 and 617F.' Discussed in this paper is the application of these data to the prediction of anhydrite precipitation in some practical steam soak and hot-water injection projects. Any simple method for predicting the solubility of an inorganic compound over a wide range of temperatures and solution compositions must be based on some assumptions, and therefore must yield approximate results. On the one hand, natural brines contain too many ionic species for all to be included in a simple scheme; on the other hand, there is no adequate theoretical basis for the exact prediction of solubility in even simple solutions of mixed electrolytes. However, it is possible at a given temperature to base a reasonable prediction scheme on two phenomena:'-' the increase in solubility with increasing total concentrations of all ions (as measured by the ionic strength; see the Appendix), and an increase due to formation of cornplexes between calcium ions and sulfate ions and between sulfate and magnesium ions. Stiff and Davis' developed such a scheme for predicting the solubility of gypsum (CaSO, ¦ 2H,O) in brines at temperatures u~ to 212F. However, for the higher temperaturei of present interest, the stable solid phase is anhydrite (CaSO,). This study involves a two-part method for predicting anhydrite solubility products. First, one predicts a value K, for a given ionic strength I and a given temperature T corresponding to mo./msr, = 1 from data of the CaS0,-NaCI-H,O system. Second, one determines a group of factors F .= F(Ca) • F(Mg) • F(SO,), where the individual factors account for increases in the solubility product due to complex formation by high concentrations, respectively, of calcium, magnesium and sulfate. Combining the two parts, one obtains the solubility product in molalities as

Jan 1, 1969

By R. J. Blackwell, J. R. Rayne, J. R. Henderson, W. M. Terry, D. C. Lindley

This paper presents the results of a laboratory investigation of the efficiency of water-solvent mixtures in recovery of oil. These mixtures may have the high displacement efficiencies characteristic of solvent floods and the high sweep efficiencies characteristic of water floods. Thus, the water-solvent process may increase the number of reservoirs in which a miscible-type displacement can be used profitably. The experiments on the use of water-solvent mixtures for recovery of oil were conducted to find the general applicability of the process. These studies demonstrated that, in flowing through sands, water and solvent segregated into a solvent layer on the top and a water layer on the bottom rather than flowing through the sands as a uniform mixture. Calculations based on the simultaneous flow of the water and solvent in layers were used to predict the effective mobility of the mixtures and the optimum operation of the process in steeply dipping, homogeneous reservoirs. As most reservoirs are not suited for the operation of the process under ideal conditions, experimental studies were conducted with sand-packed models scaled to represent more realistic reservoirs. These studies included the effects on recovery of oil of rate of injection, viscosity of oil, variations of permeablity within a formation and variations in water-solvent ratio. For the range of con-ditions studied, higher recoveries of oil were obtained with water-solvent mixtures than with water or practical volumes of solvent alone. INTRODUCTION A group of intriguing—because of their great possibilities—new oil recovery methods at the disposal of the petroleum engineer are the miscible displacement processes. These processes (high-pressure gas drive, en-riched-gas drive and LPG bank driven by methane) displace all of the oil from the portions of the reservoir swept by the injection fluid. The key question confronting the engineer applying one of these techniques to a particular reservoir is, "What fraction of the reservoir can be swept by injection of a practical volume of solvent?"." Intensive laboratory studies have been made during the past several years in seeking answers to the question of the sweep efficiencies which can be expected in solvent floods.' - These studies provided the answer that low-viscosity, low-density solvents channel and by-pass oil in sands with no dip. In horizontal sands, solvent flooding becomes less efficient as the viscosity of the oil increases, the recovery of oil at solvent breakthrough decreases and larger volumes of solvent are required to achieve a given recovery. More efficient displacement of oil by solvent is observed under certain conditions in sands with dip.".' If the permeability and dip of the sand are sufficiently high, gravity segregation of low-density solvent injected updip can prevent channeling. At rates of depletion below a critical rate,"." no channeling occurs. Unfortunately, in many reservoirs, the critical rate is so low that production of oil at rates below this rate is not economically attractive. And at rates over four times the critical rate, channeling is almost as severe in sands with dip as in horizontal sands. These findings pointed out that, for solvent floods to be generally applicable in recovering oil from all types of reservoirs, new methods of improving their sweep efficiencies are needed. Simultaneous injection of water with the miscible fluid was suggested by Caudle and Dyes7 as a method for improving sweep efficiencies. They theorize that water flowing with the solvent would decrease the effective mobility of the solvent and cause it to contact more oil sand. If, indeed, the water and solvent flowed as a uniform mixture, the process should have the advantages of the high displacement efficiencies characteristic of miscible floods and the high sweep efficiencies of water floods. Thus, the method (at least in theory) would greatly increase the number of reservoirs in which miscible-type displacements would be feasible. A research program was conducted to probe the technical feasibility of the water-solvent process. It

By C. S. Matthews, J. L. Mahaffey, W. M. Rutherford

This paper gives results of an experimental study of the sweep efficiency of a miscible displacement in a five-spot. The study was carried out in a parallel-plate glass model in which effects of diffusion were scaled at or near the molecular diffusion level. The experiments show that very early breakthrough (25 to 35 per cent of pore volume (PV) injected) may be expected in miscible floods because of the unfavorable viscosity ratio. However after 1 PV of displacing fluid is injected, the sweep rises to a reasonable value (50 to 60 per cent). Photographs show that small slugs of less than 10 per cent of PV tend to dissipate before breakthrough. A minimum slug size of 15 per cent of PV would appear to be necessary even in a relatively homogeneous formation. Presence of a slug whose viscosity is inter-mediate between that of oil and gas increases the sweep efficiency of the oil-gas system. In a typical system the sweep at breakthrough rose from 26 to 37 per cent of PV for a 25 per cent slug. The increase in sweep brought about by use of a large slug could well pay for the extra deferment cost of the additional slug material. INTRODUCTION Most miscible displacement processes involve the displacement of oil with fluids of much lower viscosity and density. The displacement process at these adverse viscosity and density ratios is dominated by instability phenomena, i.e., viscous fingers and gravity tongues. These phenomena have highly adverse effects on oil recovery. Although a number of laboratory studies have been made to determine the effect of adverse viscosity ratios on five-spot sweep patterns,l,2 the scaling of diffusion effects is uncertain. In the series of scaled model studies reported herein, an attempt was made to scale diffusion. Model studies of miscible displacements in which molecular diffusion predominates are per-mitted by controlling the parallel plate spacing which reduces convective mixing to arbitrarily small levels. To decide how this scaling relates to any particular Geld displacement necessitates an estimation of diffusion effects for the natural rock being considered and conditions under which displacement will be conducted. The approach normally taken is to extrapolate data obtained from stable miscible displacements performed in the laboratory, such as those presented by Brigham et al.3 The validity with which such an extrapolation can be applied to an unstable flow system has yet to be established. If this approach is accepted, a family of oil recovery curves can be generated for a single viscosity ratio based on Brigham's observation that the magnitude of the dispersion coefficient is dependent, among other things, upon specific rock properties. Objective of our test was to define the lower limit of this range by presenting the case where dispersion effects were reduced to the molecular diffusion level in both the transverse and longitudinal directions.

Jan 1, 1967

By A. B. Cook

Gas cycling is generally considered a much less efficient oil recovery mechanism than water flooding. HOWever, recoveries from some fields have been exceptionally high as a result of gas cycling. Recovery from the Pick-ton field, for example, was calculated to be 73.5 perceni of the stock-tank oil originally in place. In evaluating pressure maintenance projects, determining how much of the recovery is due to displacement by gas and determining how much is due to vaporization of the imrnohile oil in the flow path of the cycled gas is very difficrilt. Even though most of the oil is recovered by displacetr~ent, the success of a project may depend on the amount of oil vaporized. A limited number of experiments have heen performed with a rotating model oil reservoir that simulates gas cycling operations and allows a separation of the oil from, tile free gas flowing into the laboratory wellbore at reservoir conditions, thus revealing which is displaced oil and which is vaporized oil. It Iras been determined that the amount of varporizatio'n is .significant if proper conditions exist These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized. Data from six experiments affecting vaporization are presented to illustrate reservoir condition that range from favorable to unfavorable. 111 these eaperitnenis recovery by vaporization ranged from 73.6 to 15.3 percent of /he immobile oil (oil not produced by gas displacerrlt). INTRODUCTION Between 1930 and 1950, gas cycling was a popular. oil recovery practice. especially for the deeper reservoirs. Later, with many case history-type studies published for both gas cycling and waterflooding, it was generally believed that waterflooding was far superior to gas cycling, even when gas cycling was conducted as a primary production procedure by complete pressure maintenance. A good example illustrating the advantage of water-flooding over gas cycling is given in a paper by Matthews' on the South Burbank unit where gas injection was followed by waterflooding. The author concluded in part that "Early application of water injection, without the intervening period of gas injection, would have recovered as much total oil as ultimately will be recovered by waterflooding following the gas injection, and total operating life would have been shortened". This appears to be a logical conclusion. However, it should not be applied to all fields. Pressure maintenance with gas in the Pickton field, as reported by McGraw and Lohec;' will result in a much larger percentage of oil recovery than was obtained in the South Burbank unit. The great success in the Pickton field resulted partly from vaporization of the immobile oil in the flow path of the cycled gas. The amount of vaporization is related to the following conditions: volatility of the oil as reflected by the APT gravity of the stock-tank oil; reservoir temperature; reservoir pressure during gas cycling; and the amount of gas cycled. Therefore, the U. S. Bureau of Mines is investigating these effects on vaporization in a research project using a model oil reservoir. Three different stock-tank oils having 22, 35 and 45" API gravities are being used as base stock to synthesize reservoir oils. Experiments are being performcd to determine vaporization at 100, 175 and 250F and at 1,100, 2,600 and 4,100 psia. This is a progress report showing the results from six experiments. Other Bureau of Mines reports"- concerning vaporization are listed. LABORATORY EQUIPMENT AND PROCEDURES The equipment ' consists of an internally chromium-plated steel tube packed with finely sifted Wilcox sand. The tube is approximately 44 in. long and has an ID of 13/4 in. The sand section contains approximately 570 ml of voids, has a porosity of 32 percent, and a permeability to air of 4.3 darcies. A unique feature of the laboratory reservoir (Fig. 1) permits the tube part to rotate at 1 rpm while the outlet and inlet heads are held stationary. The outlet end contains diametrically opposed windows to permit observatlon of the flowing fluids, and two valves, one on the top and the other at the bottom. Oil and free gas. when being produced simultaneously, can be separated by manipulating the two valves to keep a gas-oil interface in view through the windows. Thus, only gas is produced through the top valve and only oil flows through the bottom valve. The laboratory equipment was designed to study vaporization. Therefore, a uniform reservoir was made using dry sifted sand as opposcd to using a consolidated sand core with interstitial water. Furthermore. the reservoir was tilted to minimize fingering of gas. This tilting also in-

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By R. Siy, O. Neiman, B. Hilscher

"A full-scale prototype of “Jameson Downcomer” technology has been installed and tested on a Tailings Oil Recovery (TOR) vessel in Syncrude’s Mildred Lake extraction plant. Jameson Downcomers are a type of mineral flotation equipment used in the coal industry that Syncrude has extended to the recovery of secondary bitumen in the oil sand extraction process. The TOR vessels are currently being operated as single-gravity separation vessels, in series with the Primary Separation Vessels (PSV’s). We have developed a model to differentiate between “floating” and “non-floating” bitumen in the PSV’s, and then applied it to verify that the current TOR performance only captures the “floating” bitumen by simple separation. The existence of “non-floating” bitumen provides an opportunity for recovery enhancement by means of the Jameson Downcomers. To achieve bitumen recovery enhancement, middlings slurry is withdrawn from the TOR vessel, and passed through a number of parallel Jameson downcomers, within which the slurry is accelerated to a high-velocity free jet, and impinged upon the slurry surface inside the downcomer, in the presence of air. The aerated slurry is returned to the middlings zone inside the TOR, resulting in an incremental recovery improvement of bitumen in the TOR. The operation of the downcomers is thought to produce suitably small air bubbles for the flotation of bitumen, either by fluid shearing during the slurry jet impingement, and/or by micro-bubble nucleation. This full-scale prototype design has met or exceeded the recovery expectations of the original Research piloting, recovering at least 40% of the non-floating bitumen. In Syncrude Extraction, this provides high business value by a separation efficiency gain achieved with modest expenditure. As well, the system has demonstrated excellent operability and maintainability.INTRODUCTION Syncrude Overview Syncrude Canada Ltd. is one of the largest producers of crude oil from oil sands. Our crude oil production facility has the capacity to produce over 15% of Canada's total oil requirements. To do this, we surface mine oil sand, extract the raw oil known as bitumen from the sand using water-based processes, and upgrade that bitumen into sweet light crude oil by fluid coking, hydro processing, hydro treating and reblending. Our final product, Syncrude Crude Oil (SCO), is sent by pipeline to three Edmonton area refineries and to pipeline terminals which ship it to other refineries in Canada and the United States. The Syncrude operation is comprised of four major technology areas: Mining, Extraction, Upgrading and Utilities. As well, Syncrude invests more than $40 million annually in science and technology, and is among the top 50 companies in Canada for Research and Development (R&D) investment. Syncrude holds 21 active Canadian and U.S. patents."

Jan 1, 2012

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By T. S. Mackey

The industrial types, sources, and quantities of US tin residues are identified and the methods of treatment reviewed. The effect of a lower tin price, due to a current major world surplus of tin metal, is mentioned and covered in some detail. The names and locations of over 100 US firms recovering tin residues are listed. Current smelting and refining charges are included to convert the residues into tin metal and alloy. The impact of the complete with-drawal of the LME daily tin price since Oct. 24, 1985, and the collapse of the International Tin Council, which at one time supported the Buffer Stock Manager, are reported with comments.

Jan 1, 1987

By J. J. Cai

The status of fossil fuel and secondary resource in metallurgy industry in China were reviewed, and conversion efficiency of fossil fuel, utilization technologies of secondary energy were studied. Fossil fuel, accounting for over 90% of energy structure in metallurgy industry, took in the highest flight in China, and a great deal of which was converted to secondary energy through the equipment of blast furnace and coke oven. These secondary energy which were mostly made of blast furnace gas(BFG), coke oven gas(COG) and Lindz Donawitz gas(LDG) occupied about 30% of total secondary energy. The way enhancing fossil fuel conversion efficiency, secondary resource recovery and the secondary energy such as BFG, COG, LDG utilization promoted to save fossil fuel was discussed in this paper. And efficient use of lower caloric value fuel was studied, such as preheating combustion air and fuel, generating electricity power etc. and regeneration purposes of high-caloric fuel was also researched, for producing hydrogen, methanol or direct reduction iron etc. The using model of secondary energy at iron and steel works was presented as fuel and chemical materials. The results suggest that utilization of these energy efficiently and reasonably could help to energy saving and environment protecting.

Jan 1, 2014

By N J. Welham

This paper reports on an innovative professional development program for school science teachers run collaboratively between the Centre for Sustainable Resource Processing and Murdoch University. Ultimately the initiative aims at increasing the pool of school students with strong science and mathematics backgrounds while highlighting the challenging careers available in the mineral resource sector including the gold industry. The program is unique in that it seeks to develop a network of science teachers who may participate in a series of workshops, short courses and tours over several years. The objective is to raise secondary school studentsÆ awareness of potential careers within the minerals sector by exposing teachers to a real life, hands-on look into the mining and minerals resource industry. Though the program includes the breadth of the resource processing sector, the potential value to gold processing is in developing a greater pool of potential employees. The initiative allows teachers to develop a better insight into the practical applications of the theoretical sciences they are required to teach. The evolution of the program from the first trials with Western Australian teachers to the introduction of the initiative to Queensland teachers are reported on. Additionally, the results of a pilot study involving 40 participating teachers are described. This study used a questionnaire and follow-up interviews to gain quantitative and qualitative feedback from teachers. There is evidence that the professional development program has resulted in teachers acquiring a new found appreciation for the application of the fundamental chemistry and physics they teach within the school curriculum. Also reported are associations between teacher participation in this professional development program and changing attitudes towards the industry in a positive way. Finally, there is some indication that these positive teacher attitudes may result in their students developing a better understanding of the diversity and availability of career paths within this industry.

Jan 1, 2007

By Robert Adams

Secondary or scrap materials appear at all stages in the industrial process and in a bewildering variety of forms, grades, and values. It is useful to begin analyzing them by dividing the broad concept of "Secondary Supply" into three parts First, the concept must encompass the stock, or pool, of secondary materials. In the process of satisfying his wants, man produces desired products from the materials and natural resources found around him. As long as the rate of production is greater than the rate of obsolescence of a given product, the total stock or pool of materials embodied in that product will increase in size This stock concept relating to secondary materials is directly analogous to the "resource" concept used for primary raw materials in the preceding chapter, and includes all materials embodied in existing products (Obviously, this excludes those materials which are destroyed in the consumption process, viz , fuel oil burned to provide heat.) Consumption of a primary material in a productive process tends to reduce the resource base of that primary material In direct contrast, however, the production or use of products increases the resource base of the secondary material. Thus, we find that a country which has no resource of a primary material can, by importing products that contain the material, build up a large enough stock to provide a basis for secondary recovery. The estimated growth of the pool of copper in use in the United States through 1967 is shown in Table 5.B.1.a The estimate of 39 3 million tons at the end of 1967 includes only technologically recoverable copper and is, therefore, somewhat less than the stock concept described previously, which does not distinguish between recoverable and unrecoverable material. Nevertheless, Table 5 B.1 does give an idea of how a nation's secondary resource of a material can grow over the years. A second aspect of the concept of secondary supply is the generation of secondary materials. This includes materials generated as scrap in production as well as the movement of a material out of the stock of existing products via wear, damage, or obsolescence The quantity of materials generated is usually either nearly or completely independent of the technologic capabilities and economic forces which prevail in the secondary recovery market.b The justifications for and the qualifications to this statement are considered later. The final aspect of the concept of secondary supply consists in the secondary recovery process It is at this point that the technologic and economic forces of the secondary recovery market become the controlling fac-

Jan 1, 1976

By Erik Westman, Benjamin Mirabile

"Ongoing research is being conducted to evaluate secondary support performance in longwall ventilation entries. In a three-entry longwall gateroad, secondary supports are applied in the #2 entry to maintain a functional airway for the entirety of second panel mining. This airway represents a pathway for contaminated mine air to travel from the longwall tailgate to the mine bleeder system. The ground response curve concept may be used as a design basis for selection of appropriate secondary support in these ventilation entries. Two types of secondary supports are monitored for load and convergence in this project. These monitored supports are pumpable crib supports and interlocking wood crib supports. To evaluate the effect of support density, two installation patterns are monitored for each support type. Both a single-row, protected airway pattern and double-row, full entry support pattern are monitored for each support type. Load and displacement data is collected for all support patterns as second panel mining retreats past instrumentation sites. Data is collected for approximately 200-feet inby the second panel face or as long as safely possible. Load and convergence data collected will be used to calibrate numerical models that will simulate ground response curves for the #2 entry inby the second panel face.INTRODUCTIONWhen a bleeder ventilation system is used, the #2 entry of a three-entry longwall gateroad system is designed to function as a pathway for contaminated air from a longwall face to the bleeder system during second panel mining. The #2 entry is subject to substantial ground movement and loading during its function as an air course because it is a single entry between two longwall gobs. Secondary support is regularly applied in this entry to maintain air course functionality during second panel mining.Research on performance and design of secondary supports has been conducted extensively over the last 30 years (Barczak and Gearhart, 1993; Barczak and Gearhart, 1994; Mucho, Barczak, and Dolinar, 1999). This research has focused heavily on the application of secondary support in longwall tailgate, with little research on the application of secondary support in bleeders or other ventilation entries (Mirabile and Westman, 2018). Secondary supports in #2 entry are likely to experience similar loading and ground movement as those applied in the tailgate entry. However, the designed lifespan of the mine entry and the definition of acceptable ground conditions differs from mine entries where more extensive research has been conducted."

Jan 1, 2019

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By James Douglas

THOUGH liberality is not supposed to be a prominent trait of the Scottish character, Canada owes to a Scotchman, Sir Wm. Macdonald, more than to any other of its people, not only wise ideas, but pecuniary help towards extending education: and another Scotchman, in New York, has sumptuously housed under one roof three branches of the engineering fraternity, of which we are one. Having thus created us members of the same family-for the metaphorical meaning of house and kinship is identical-Mr. Carnegie expresses more emphatically than even he could in words, that, by affording facilities for closest intercourse, he in¬vites the mechanical, electrical and mining engineers to par¬ticipate in the freest interchange of idea and experience, and to correlate and combine the results of their studies and activi¬ties; and, being members of the same household, to banish re¬serve and secrecy. And now we, the members of the - American Institute of Mining Engineers, meet as though we were at home in a neighboring country. For whether we meet in Canada, in England, or elsewhere, the Institute is always received as though no political or geographical divisions separated its members from those of congenial associations in the land of its host. In truth, the title which we have assumed claims for the sphere of our activities the whole American continent, regardless of such trifling details as boundary-lines. The fact that we meet to communicate each other's experience, to discuss our difficulties, and to seek each other's aid in solving the intricate problems that so often present themselves in the course of our profes¬sional life, is an acknowledgment of our individual helpless¬ness; and therefore an argument for united effort. But no effort can be of any value if there is an underlying suspicion

Jan 9, 1907