Search Documents

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By George W. Little, John Councilman

"The selection, evaluation, and modification of contractor mix designs for self-hardening seepage barriers, completed by the slurry trench excavation method, can be one of the most critical and challenging tasks to ensure the cutoff wall meets the design performance criteria. Contractor mix designs should incorporate all available geotechnical data, including subsurface soil characteristics, groundwater information, and potential site contaminates. However, the pre-construction mix design can have limitations if subsurface data is limited or shows variability from initial investigations. Placement of the seepage barrier material needs to be evaluated during construction to identify in-situ performance. In one particular case study, the self-hardening cutoff wall mix design was evaluated over a one year period followed by a year and a half installation period, in which, a number of adjustments were made to the laboratory mix design during construction due to performance in the field. Installation for the selected mix was monitored on a real-time basis, using quality control data, as well as early strength and permeability results to determine if adjustments to the self-hardening mix were necessary. Evaluation of early results and relationships between strength and permeability were used to make adjustments prior to achieving the final test results for 28-day strength and permeability. Test results of the installed mix illustrated a direct correlation between strength and permeability. Achieving a minimum unconfined compressive strength was necessary to meet the minimum permeability of the seepage barrier. Other determinations conclude that the thorough development of a pre-construction mix design can have limitations even when all geotechnical data and site conditions are taken into account. Understanding early indicators and key strength and permeability relationships are necessary to determine seepage barrier performance and limitations.IntroductionThe evaluation of contractor mix designs for self-hardening seepage barriers was reviewed for one particular case study where a mix was developed using available geotechnical background information, including considerations for impacted groundwater. Following development of the laboratory mix design, the seepage barrier wall was installed over a one and a half year period, where the contractor mix design was evaluated and modified to accommodate field conditions affecting performance. The objective of the project was to cutoff and collect impacted groundwater and prevent the migration of contaminants to the creek running adjacent to the project. The self-hardening seepage barrier wall was installed using the slurry trench excavation method along 4700 ft of alignment and extended to depths ranging from 20 to 85 ft below ground surface, where it tied in with a low permeability stratum or competent bedrock."

Jan 1, 2016

By K. E. Robinson

During operation of tailings impoundments, water is lost through decanting, evaporation and seepage. Techniques have been developed to regulate or control each of these components. Collectively implemented, these techniques form the basis of tailings impoundment management. Regulation of the rate and level of decanting influences the size of a free water pond, and, thereby, the amount of evaporation and seepage, which are both area-dependent. Conversely, the encouragement of seepage and/or evaporation could also be used to reduce decanting requirements. Management of one of the components of a tailings impoundment's water balance is reflected in changes in the other components. The seepage component has the greatest potential impact on the environment, and consequently requires the closest scrutiny. Water percolating through tailings backfill transports heavy metals and other dissolved solids from the impoundment into the local groundwater regime. Depending on the seepage volume and concentration of contaminants, seepage from impoundments could exceed environmentally tolerable limits. Once mobilized, seepage-borne pollution is much more difficult to treat, mainly because of the problems in collecting the diffusive transportation medium. Pollution abatement measures relative to tailings impoundment seepage depend on seepage prevention or reduction. Seepage control measures include constructing barriers to flow, pump-back systems of interception and restricting the supply of water available for seepage.

Jan 1, 1987

By Carlon C. Chambers

INTRODUCTION Manufacturer sponsored research over the past three years has proven the suitability of styrene-butadiene/ asphalt membranes in many waste disposal seepage control applications for the mining industry in general and uranium mining and milling in particular. The class of membranes that have been tested are SBR/asphalt blends containing up to 68 weight percent asphalt, the balance being elastomeric polymers, fillers and phase compatibility promoters. These membranes are classified as thermoplastic, elastomeric materials and can be hot spray applied to any moderately dry substrate at 177°C (350°F), and placed in service within one hour of application. The properties of this membrane that make it suitable for use as an engineering_ material in these applications are discussed. These properties include chemical resistance, bacterial resistance, UV light resistance, permeability, stress/strain characteristics and bonding data. The favorable economics of the system are also discussed. The preliminary raw test data on the above properties were reported in a previous paper, (Chambers, 1980) and most will not be repeated here. Instead, this report considers the original data in relation to subsequent data and concentrates on interpretation of the trends for engineering purposes. However, several of the pictures contained in the original paper are reproduced in this report for illustration purposes. BACKGROUND Asphalt alone has a long history of use as a water-stop material. Its limitations of becoming brittle when cold and soft when hot, however, are well recognized. The service temperature for common grades of asphalt is usually in the 4° to 49°C (40° to 120° F) range. Modifications to the base asphalt can generally improve its performance at the high end of the temperature range by raising its softening point, but only the addition of one class of modifiers, elastomeric polymers, improves low temperature flexibility as well and also adds resilience. Both of these properties are of extreme importance if the waterstop material is to maintain its integrity when used on substrates which are unstable, non-cohesive, discontinuous or have significant expansion/constraction coefficients. Although there are many elastomeric polymers which can be used with

Jan 1, 1980

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By J. F. Whelan, B. D. Marshall, Z. E. Peterman, J. B. Paces, L. A. Neymark

Observations of calcite and opal in cavities in the unsaturated zone at Yucca Mountain indicate that: 1) seeps are not regularly spaced in underground workings and not all fractures sustain flow, 2) many cavities represent sites of seepage that have remained stable for millions of years, 3) typically there is no evidence (such as dripstone) for seepage dripping into cavities from their ceilings, and 4) seepage is not likely to be greater than about 1 liter of water per year (per 5-m-long drift) based on calcite abundances observed in the ESF. This estimate of seepage is significantly lower than that used for performance assessment.

Jan 1, 2000

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By D. B. McWhorter, J. D. Nelson

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1981

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By C. D. Hebert, T. Gregor, M. Ghazi, G. J. E. Kramer

This paper describes the recent application of gasketed, precast concrete segmental lining design that has improved tunneling productivity and quality. The speci?c segment arrangement includes: six-piece ring with equal 60 degree gasketed segments, juxtaposed key and counter-key segments, trapezoidal and parallelogram shaped segments, inclined and skewed radial joints and plastic circumferential joint connectors. This allows rapid, but accurate ring erection, reducing mine cycle times. The design avoids cruciform joints, minimizes potential gasket damage and eliminates the need for separate left and right ring molds. The implementation on the Los Angeles ECIS and NEIS sewer projects is described.

Jan 1, 2003

By Stefan Mede

Robot Supported Moulding—this is the name of Herrenknecht Formwork’s entry to the world of automated segment production. What had been considered impossible for a long time, has been achieved by Herrenknecht experts together with the Swiss company Marti AG: unmanned segment production on the working line. The moulds open and close autonomously with the help of a hydraulic system. A robot cleans and greases the moulds at one work station and inserts the injection sockets at another. The next step will include further automation and digital networking of all processes from production to installation in the tunnel.

Jun 13, 2021

By Botond Beno, Dave Watson, Danny Read

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing I-64 four-lane bridge-tunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. The design-build contract was awarded to Hampton Roads Connector Partners with HDR and Mott MacDonald retained as lead designers in a Design Joint Venture. This paper will highlight some of the e challenges related to the design of the twin bored tunnels from spaceproong, tunnel enabling wors, segmental lining design and durability considerations.

Jun 23, 2024

By L Drowley

The Adelaide Desalination Plant (ADP) draws raw sea water into the facility and returns saline concentrate to the Gulf St Vincent via subsea conduits. This paper describes the detailed design and construction methodologies developed for the cross connection tunnel excavation. The paper concentrates on key design elements which include:· lateral breakout support of the segmental tunnel lining,· ground improvement grouting in the zone of the cross connection tunnels due to extremely variable and weak ground conditions, and· excavation methodologies and proposed support types of the riser to tunnel cross connections.The design process consisted of developing concepts, detailed risk assessment, three-dimensional (3D) finite element modelling and structural analysis for temporary support of tunnel lining; functional design of the ground improvement grouting and the temporary support; and permanent lining design of tunnel to ocean riser connections in a mixed soft ground/hard rock environment.The paper also presents conclusions of the design based on construction data available, and highlights the close collaboration between the design team and construction team.

Mar 8, 2011

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By Iván Espinoza

El yacimiento de Horizonte es un sistema de vetas auríferas de qz ± sulfuros del tipo mesotermal, que está emplazado en el Batolito de Pataz, un intrusivo Mississipiano localizado en el margen occidental de la cordillera Oriental de la parte norte de los Andes Peruanos. En ese sentido, el presente trabajo describe la exploración geofísica realizada en el primer trimestre del año 2008 en Parcoy, con la finalidad de encontrar nuevas zonas de mineralizaciones potenciales y completar el modelo estructural en la zona. Para ello, se elaboró el proyecto de exploración PD para Parcoy, a través del método IP, el cual es usado en la búsqueda de mineralización de oro, así como el uso de sondajes diamantinos a las nuevas zonas detectadas por la geofísica. Como resultado de ello, se determinó 6 zona anómalas de interés prospectivo para ser analizado por el departamento de exploraciones.

Sep 14, 2009

By M. L. Fuller

IN connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segre-gate structures of the Widmanstätten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith1 the plane of segregation in the matrix con-tains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the literature.2 The increasing com-mercial importance of zinc alloys containing copper makes this funda-mental study of value to the metallography of zinc alloys.

Jan 1, 1933