Search Documents

By S. S. Clarke

Late in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of Jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of Jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1949

By John G. Tate, George W. Nicolson, James L. Bruce

For more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.' From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. Description of Ore Bodies The shape Of the Ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions) extending from unknown depths below the bottom level at elevation 250 ft below sea level) to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the Ore body extended to surface and was Mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the Ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upper-side of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and Clay sedimentaries of Miocene and later age, The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-Stained by the descending meteoric waters, It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pet Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pet. on the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main Ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. 'This probably can

Jan 1, 1949

By S. M. Moore

Each year more than 400 coal miners are injured (fatally and nonfatally) by rock falling from between or around roof supports. Many of these injuries can be prevented by the installation of roof screen. However, many coal mines are reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential savings in workers' compensation (W C) premiums that can be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by Illinois and Kentucky were investigated in this study. Using data obtained from the Mine Safety and Health Administration, national and state WC bodies and individual insurance companies (e.g., average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), baseline mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state's actual WC rate-setting formulas, a sensitivity analysis was conducted to determine the total savings in WC costs after a three-year period. Annual savings in WC premiums ranged from $41,000 to $326,000 for the 67-person mine, and $96,000 to $843,000 for the 150-person mine. An economic analysis of the cost of a roof screening program at a 67-person mine was also conducted. The annual cost of a roof screening program here was estimated at $240,000. At this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By F. R. Archibald, C. M. Nicholson

The present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay, There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity hut they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the Property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time priding review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3,460,000 The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time Operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1949

By W. R. Seyfried

The problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. The Process as Planned In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the company, first drafted a process in July of that year—five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or lour-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F). (b) The roasted ore would then be leached with hot aqueous ammonium bi-sulphate to form a slurry. In this way the

Jan 1, 1949

By J. D. Edwards

When Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipmerits through the caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. Bayer Process The Bayer process has been almost universally used for the production of alumina from bauxite. This process, in outline, comprises the digestion of hely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium alumi-"ate and the impurities—oxides of iron, titanium and silicon—remain undissolved. The undissolved residue, known as "red mud,'' from its color, is separated and run to waste. AluKlinum hydrate (A12O3.3H2O) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the Process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1949

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Robert Maddin

The application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure generallv has been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. Experimental Procedure and Results Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,' were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 120° apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual x and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.³ In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig I shows the initial and final positions of the specimen axes of the crystals. At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to One another' Fig 3-57 photographed On different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1949

By G. Sachs, E. J. Ripling, J. J. Lynch

It is general practice to evaluate the strength properties of a particular metal from its stress-strain (s1 — el) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress," (s), and a certain limiting strain, the "ductility" (es), before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (I) the shape of the neck and (2) average values of the stresses and strains over the cross-section at the moment of fracture. However, for the pur. pose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusiom also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locos of failure. In this paper, the effects of straining (at room temperature) by various methods on the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to Our present knowledge, any such prestrainitlg results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain,'' from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1949

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By James T. Kemp

Some interesting and, to American eyes, rather unusual processes for refining impure aluminum derived from scraps were found by American and British investigators who went into Germany in 1945 for the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. What was found was recorded in a series of reports (see page ), many of which have been released for general reading. This paper gathers under one title and summarizes the German work in refining light metal scrap. Reference must be made to the original reports for greater detail. Basically, the occasion and stimulus for the German developments in treating light metal scrap were hard necessity. Germany needed the metal for a rapacious war industry. Adequate supplies of new aluminum from reduction works were not assured. Great quantities of airplane and other light metal war scraps were forecast. It was evident that the scrap metal would have to be reabsorbed by the producing industry and would have to be kept of good quality. The normal current production of manufacturing scrap was being and could be consumed as generated. It offered no technical problem. The mixed scraps, especially those arising from crashed and decommissioned airplanes, however, presented problems of another kind. Airplane Scrap The recovery of usable aluminum alloy from the mixed assemblies that made up the piles of airplane scrap was attacked in different ways by different groups and with differing degrees of success. Three procedures actually were used on a commercial scale, one was in pilot-plant stage and another had come to a halt in the laboratory a year before Germany collapsed. Four of these five processes actually involved "refining"; that is, some measure of purification of the metal after melting. Sorting and Separation on a Sloping Hearth The simplest procedure for utilizing airplane scrap involved no refining in the strict sense of the word. This was the practice adopted by two representative plants visited by the author, the Leipziger Leichtmetalle Werke, Rackwitz, Saxony, and the Vereinigte Leichtmetalle Werke, Hanover. These firms did essentially the same thing that was done in England but not with equal success, to judge by their shorter experience, the smaller tonnage handled and by the number and quality of alloys produced. The two German firms named rough-sorted scraps by their easily recognizable alloys, essentially by part and shape. They used hand labor to chop and hack and tear apart. The easily separated heavy metal and nonmetallic scraps were discarded as they were found. Steel and the higher-melting-point metal parts riveted to aluminum or built into

Jan 1, 1947

By James T. Kemp

Some interesting and, to American eyes, rather unusual processes for refining impure aluminum derived from scraps were found by American and British investigators who went into Germany in 1945 for the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. What was found was recorded in a series of reports (see page ), many of which have been released for general reading. This paper gathers under one title and summarizes the German work in refining light metal scrap. Reference must be made to the original reports for greater detail. Basically, the occasion and stimulus for the German developments in treating light metal scrap were hard necessity. Germany needed the metal for a rapacious war industry. Adequate supplies of new aluminum from reduction works were not assured. Great quantities of airplane and other light metal war scraps were forecast. It was evident that the scrap metal would have to be reabsorbed by the producing industry and would have to be kept of good quality. The normal current production of manufacturing scrap was being and could be consumed as generated. It offered no technical problem. The mixed scraps, especially those arising from crashed and decommissioned airplanes, however, presented problems of another kind. Airplane Scrap The recovery of usable aluminum alloy from the mixed assemblies that made up the piles of airplane scrap was attacked in different ways by different groups and with differing degrees of success. Three procedures actually were used on a commercial scale, one was in pilot-plant stage and another had come to a halt in the laboratory a year before Germany collapsed. Four of these five processes actually involved "refining"; that is, some measure of purification of the metal after melting. Sorting and Separation on a Sloping Hearth The simplest procedure for utilizing airplane scrap involved no refining in the strict sense of the word. This was the practice adopted by two representative plants visited by the author, the Leipziger Leichtmetalle Werke, Rackwitz, Saxony, and the Vereinigte Leichtmetalle Werke, Hanover. These firms did essentially the same thing that was done in England but not with equal success, to judge by their shorter experience, the smaller tonnage handled and by the number and quality of alloys produced. The two German firms named rough-sorted scraps by their easily recognizable alloys, essentially by part and shape. They used hand labor to chop and hack and tear apart. The easily separated heavy metal and nonmetallic scraps were discarded as they were found. Steel and the higher-melting-point metal parts riveted to aluminum or built into

Jan 1, 1947

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,&apos;&apos; while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

It is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4.5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik&apos;s tests will be discussed later Such torsion does not readily yield actual stress and strain values. Therefore a pre- liminary study was made of the effects of repeated direct stresses, that is, tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluniinum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension rest This alloy permitted, therefore rather accurate cont.rol at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this invest~gation appear sufliciently interesting to extend the method of attack in various directions It is intended to study (11 the effects of cycles up to a tew thousands and (2) the effects of strains of different magnitude in tension and compression respectively &apos;The latter variable also includes a. a special case the effects of compressive strains.

Jan 1, 1949

By A. H. Geisler, F. Keller

Although the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron Microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the Precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstatten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged a1loys.l The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will sufficc to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. Preparation OF Specimens The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously,¹,² Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen, The specimen is polished accordillg to the usual procedure for microscopic examination.³ he specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended, Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens, The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet PoliShing operation are generally used, but frequently the as-rolled surface is Suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1947

By F. Keller, A. H. Geisler

Although the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron Microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the Precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstatten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged a1loys.l The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will sufficc to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. Preparation OF Specimens The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously,¹,² Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen, The specimen is polished accordillg to the usual procedure for microscopic examination.³ he specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended, Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens, The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet PoliShing operation are generally used, but frequently the as-rolled surface is Suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1947

By Yves Dardel

The literature concerning the remelting of alunlinum and its alloys is very rich. Unfortunately the majority of the papers on this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges, and the atmosphere of the furnaces bring into the bath during the successive remelt-ings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, or others, if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H², O2, H²O, co², CO, CH,, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of sieverts3 as a function of its partial pressure PH2 in the atmosphere m = K vPH² [I] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Rijntgen and Braun4, RÖntgen and M611er5, Bircum-shaw6 and Winterhagerl have rendered it possible to determine the value of K, when the temperature is less than 1.000°C. One obtains: log K = - 4,702.5T + o 238 [2] Besides its usual significance, the term Ph~ represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is1 when no gas exchange Occurs between the two phases, the Pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary Occurs, the quantity of H² should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature decreases, the internal pressure of H² increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a a depending On the hydro- static pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However1 even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1949

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949