Search Documents

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By Leonard A. Eros

In many mining applications it is not practical to use gravity takeups. In these situations hydraulic takeups are often utilized. Performance specifications are often compromised by designs which have inherently high internal friction and inefficient hydraulic designs. This results in performance which does not match the requirements of the conveyor system. A computer model has been built to check unit efficiencies and field measurements have been taken which verify the results.

Jan 1, 1993

Simple quotation of quantities of coal reserves neglects the relationship between qualities of coals and their efficient use. If exploitation of a deposit is contemplated, its life expectancy can be deduced only if its reserves are estimated according to the coal user's technological standards. A wide range in properties will satisfy a steaming coal, whereas a high vitrinite high rank coal would be preferred for coking and a low inertinite low rank coal for conversion. In competitive trading the buyer's commercial specification may require weighing against the producer's practical ideals, especially when beneficiation is critical. Differentiation of grades in quality of a deposit provides an intelligent understanding of the economic importance of the deposit. The Wongawilli seam of the New South Wales Southern Coalfield exemplifies the effect of quality criteria upon the extent of in situ, recoverable and marketable classes of economic reserves. Effective management of a deposit will result from simultaneous quotation of coal qualities and quantities in a statement of its reserves.

Jan 1, 1979

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

The grade (or value) to volume relationship which constitutes a target orebody is used to show that the concentration of diamonds in an economic deposit may be as low as O.Olg/t. Diamond valuations from an Indonesian deposit demonstrate that the largest 5% of the diamonds in the deposit contributed 25% of the mass of diamonds recovered and 70% of the value from the ore. The need to consider the large stone content and the probability of recovery is used to estimate that the sampling density is required to be as high as 4-10,000ppm for a VLC deposit. This is compared with an acceptable sampling density for a bauxite deposit of 700ppb. A case history of the discovery of a diamond bearing paleo-channel in the Ellendale field in Western Australia illustrates that the sampling task becomes impractical. It requires an excavation in excess of 300,000 bcm of material to prove a 5M hem ore reserve. The conclusion is reached that setting up a small scale mining operation is an appropriate method of proving such an ore reserve and that the Code of Reporting should allow a category of "Mineable Resource" to cover such a situation.

Jan 1, 1990

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

Underground space can be defined as space below natural ground level which can be used as an alternative to an above ground location. While many of our above ground structures inherently involve underground excavation for foundations and services, the term underground space specifically refers to organised development of underground openings and of the underground domain. For example, the services to a city such as power, gas, sewerage, water and communications are installed in a congested array which usually requires roads to be dug up when the services need to be accessed. An underground space installation of services would involve a well planned conduit which is easily accessed without any excavation. The concept of using this virtually untapped land resource to the advantage of our expanding cities is gaining considerable interest in Australia. Overseas, in the Scandinavian countries and some Asian countries, underground space has been used for centuries; in Great Britain, France and the United States of America over the last century and in Japan for over a decade. This paper focusses on the types of underground space usage which should be competitive with above ground use and suggests areas in which the competitive edge may be improved in favour of underground space. In particular, considerable advantage is seen by using well-planned underground space developments in major cities, where the strategic central location of the development takes advantage of proximity to potential users. However, the largest single factor affecting the acceptance of underground space is the high capital cost of construction, even though an underground space development may result in lower operating costs and reduced long-term maintenance costs. While excavation methods and associated costs are very much site-specific, the importance of applying the latest technology in rock breakage, with consideration of ground vibration, excavation rates and ground support, remains a major challenge to the development of underground space.

Jan 1, 1995

A wide variety of process streams are sampled for grade control in the mining industry. However, in many instances the overall precision of the resultant analyses is inadequate for the intended purpose, ie grade control and optimisation of resource utilisation. Consequently, special attention needs to be given to the sampling, sample preparation and analysis procedures in place to ensure that meaningful grade control decisions can be made based on the analyses generated. For example, it is virtually impossible to control a process to within, say, ¦0.2 per cent if the overall precision of the analyses is no better than 0.5 per cent. Hence, precision targets appropriate for the task need to be established and the overall precision achieved in practice monitored and controlled on an ongoing basis.

Jan 1, 2008

By Ralph J. Holmes

"An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and sold commercially is crucial to resource definition, effective resource utilisation, plant design, process control, metallurgical accounting and finally quality control to ensure that contract specifications are met and equitable payment is received for product sales. However, the responsibility for sampling is often entrusted to personnel who do not fully appreciate the significance and importance of collecting fully representative samples for analysis, and they seem satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. There is really little point in accurately analysing samples if they are not representative in the first place, because the resultant analyses can be seriously biased and the effort taken to carefully analyse such samples is largely a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts and significant revenue losses due to poor sampling practices at the point of sale. Consequently, it is critical that sampling is given the attention it deserves as the first important step in the quality measurement chain. The golden rule for correct sampling is that all parts of the ore, concentrate, slurry or other material being sampled must have an equal opportunity of being collected and becoming part of the final sample for analysis."

Jan 1, 2016

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Randy Wheeler

The importance of having full wave form information for recorded blast events cannot be overstated. Knowing the peak particle velocity and the frequency at the peak are the tip of the iceberg. This presentation will focus primarily on using the FFT (fast Fourier transform) for detailed frequency analysis. Employing linear superposition to evaluate timing effects on amplitude and frequency will be discussed.

Jan 1, 2005

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By Ronald R. H. Cohen, Margaret W. Staub

Two pilot scale bioreactors designed to treat acid mine drainage primarily using sulfate reducing bacteria were constructed underground at the Eagle Mine Superfund site in Minturn Colorado. The project was designed to test th applicability of microbiological treatment on water with high metals concentration and to test the process in an underground environment. Objectives were, 1) to compare metal removal, pH increase, and sulfate reduction in a single stage reactor with a double stage reactor of equal volume at varying flow rates; 2) to determine where within the substrate treatment occurs· and 3) to examine volume versus surface ara as a design parameter for optimizing metal removal processes. Results from the reactors showed that the single stage reactor and double stage reactor performed equally well for the removal of Cd, Cu, Pb, Fe, Mn, and Zn. pH increased above 6.5 in both reactors. Greater than 97% of metals were removed within the first ten inches of substrate. Volume proved to be a more useful parameter for determining removal rates than area. Using volume as a design parameter rather than surface area enables PMDT systems to be constructed as packed columns rather than broad wetlands, Thus, space requirements are significantly reduced.

Jan 1, 1993

By F. R. Archibald

IN a recent paper on Roasting of Beattie Concentrate (1), the importance of controlling the temperature, and the sulphur dioxide concentration was pointed out. It is the purpose of the present paper to present further information by which the most satisfactory conditions for roasting are more specifically defined. Incidentally, a method of illustration is developed for representing roasting curves on a three-dimensional diagram. The primary purpose of this investigation, as in the case of the earlier work, was the search for information that would be of practical value in improving plant operation and gold recovery. For this reason, emphasis is laid on the regulation of essential variables and on definition of their optimum values and limits for maximum gold recovery in the subsequent cyanidation process. Good roasting is considered at least as much an art as it is a science, and, in this light, theoretical consideration of the nature and sequence of the chemical reactions involved is of secondary importance. The presentation which follows includes a series of graphical illustrations, an interpretation of the graphs, some theoretical considerations, and a description of laboratory technique.

Jan 1, 1940

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022