Search Documents

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

By D. U. Deere, F. D. Patton

Introduction A close relationship exists between the geologic investigation and the stability analysis of the slopes of an open pit mine. One significant result of this relationship is that the stability analysis is no better than the assessment of pertinent geologic factors that enter into the analysis. In some slope stability problems the engineering solution becomes obvious once the geologic framework is established. In other cases, establishing the geologic framework is only the first stage in the process of analysis. However, even in these cases the geology should not be neglected once the analysis is made. The geology should be periodically reviewed when new slopes are excavated. This will help ensure that the basic assumptions for the analysis have not changed and will permit changes when new conditions are encountered. In recent years improved methods of stability analysis have been accompanied by advances in laboratory testing techniques and new knowledge of the shear strength of rock discontinuities. At the same time there have been improvements in field geological descriptions. As more experience is gained in analyzing and predicting the stability of rock slopes, the importance of certain geologic factors has become more apparent. Some of these factors were described in a paper given at the Open Pit Mining Symposium in Johannesburg, South Africa in September 1970 (I). This paper includes many of the points covered at that meeting but with additional emphasis on the significance of the major geologic structures. Other papers given at the South African symposium also considered geological and hydrogeological factors in slope stability analysis (2) (3) (4) (5) (6). This paper first describes the approach to a slope stability problem including assessment of the relative roles of field geology studies, laboratory testing, stability analyses, and continued slope monitoring studies. Next, is described a framework which has been found useful for classifying or separating the several types of slope stability problems encountered in open pit mines. The principal geologic factors in slope stability problems in rock are discussed and brief comments are made on how these factors distinguish stability problems in rock slopes from those normally encountered in soil slopes. The over-riding control of major geologic structures, especially faults, in most slope stability problems is emphasized. In this regard the relative importance of statistical studies is contrasted with knowledge of the positions of key structural

Jan 1, 1971

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

By Malcolm Heyburn

Airborne and ground magnetic surveys were made over and in the vicinity of the Sanford Hill ore body at Tahawus, Essex County, New York. These geophysical surveys served to: l. delineate, lithologic and structural features associated with the ore bodies; 2. indicate a major extension of the Sanford Hill ore body; and 3. guide a drilling program to prove this extension. The titaniferous magnetite ore body at Sanford Hill is associated with gabbro occurring in anorthosite. The contrast in the magnetic susceptibilities of these rock types, reflected in the magnetic measurements, allows geologic-mapping showing rock types and inferred structural features. The anomalous magnetic high of the airborne magnetometer survey indicated a southern extension of the Sanford Hill ore body. Diamond drilling, guided by the airborne and specifically the ground magnetic results, substantiated this interpreted ore extension to be of major magnitude.

Jan 1, 1961

By T. E. Wayland

Bentonites are clay materials composed principally of minerals in the montmorillonite group. Distinctive physical properties of the montmorillonite minerals are responsible for selected bentonite deposits having become the raw materials source of industrial clay products which are virtually essential to the maintenance of high production standards in the petroleum, foundry, taconite and other basic industries. These versatile materials have no suitable substitutes in either their major applications or in hundreds of speciality products, The economics of the bentonite mining industry follows closely the established pattern of other non-metallic raw materials. Aggressive competition, advanced technologies, progressive marketing techniques, substantial reserves, and vast unmeasured resources insure the continued supply of high quality bentonite to industry at bargain prices. The purpose of this paper is to discuss the geology and economics of bentonite deposits, summarize both major domestic mining districts and foreign deposits, and report significant results of research and development.

Jan 1, 1970

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By Alan C. Noble

Ore reserves are often less than 30% of geologic resource estimates that are initially prepared by exploration geologists. Differences of this magnitude between resources and reserves can lead to serious . problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves and are later found to be misleading and gross overstatements of ore reserves. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery, and economics early in the project and by using appropriate qualifiers in the resource statement Examples using typical deposit characteristics are used to demonstrate how cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1992

By A. C. Noble

Ore reserves are often less than 30% of the geologic resource estimates initially prepared by exploration geologists. Differences of this magnitude can lead to serious problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves but are later found to be misleading and gross overstatements of the actual ore tonnages. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery and economics early in the project and by using appropriate qualifiers in the resource statement. Examples using typical deposit characteristics are used to demonstrate how the cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1994

By M. R. Hegge

The Jabiluka One and Two uranium deposits occur in Lower Proterozoic metasediments of the Cahill Formation, which is part of the Pine Creek Geosyncline in the East Alligator River area, Nothern Territory. The Jabiluka One deposit coincides with a "window" through unconformably overlying Middle Proterozoic sandstone of the Kombolgie Formation; Jabiluka Two is completely covered by that sandstone. The observed part of the Cahill Formation exhibits four horizons which are favourable hosts for uranium mineralization. These have been folded into an east-southeast-striking, gently plunging, open asymmetric syncline-anticline structure. The host rocks are mainly chlorite and/or graphite schists and their brecciated equivalents which have undergone initial regional prograde metamorphism to the amphibolite facies, then retrograde metamorphism to the greenschist facies. Mineralization consists of pitchblende, mainly filling open spaces and to a lesser extent in disseminated form. Chlorite, pyrite and quartz are commonly associated with the uranium mineralization. A portion of the Jabiluka Two deposit contains economic concentrations of gold. Structural preparation with low-pressure conditions at these sites appears to be the most significant ore control. Genetic hypotheses favour initial deposition in Lower Proterozoic sediments, followed by remobilization during later orogenic events. The deposits bear a marked similarity to some pitchblende deposits in central Canada.

Jan 1, 1977

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

"The rocks of Notre Dame Bay form part of the Central Paleozoic Mobile Belt (Williams, 1964) of the Newfoundland Appalachians. The Central Paleozoic Mobile Belt of the northern part of the island consists predominantly of Lower and Middle Ordovician rocks overlain by Silurian elastic and volcanic sequences and underlain in the marginal zones of the belt by polydeformed metamorphic rocks of the Gander Lake Group (Kennedy and McGonigal, 1972) in the northeast and the Fleur de Lys Supergroup (Neale and Nash, 1963; Kennedy, Phillips and Neale, 1972) in the northwest. The Ordovician rocks of the Central Mobile Belt have been subdivided into a number of local groups in different parts of the region. The Lush's Bight Group was first defined by MacLean (1947) . Recently Marten (1971) has revised the definition of this group, as shown in Table 1 and his revised definition is accepted in the present paper. Plate tectonic models that have been proposed for the development of the Newfoundland Appalachian System have indicated that the mafic volcanic rocks of western Notre Dame Bay represent oceanic crust (Bird and Dewey, 1970; Dewey and Bird, 1971; Church and Stevens, 1970) which marks the remnants of the proto-Atlantic Ocean first proposed by Wilson (1966) . Such models infer that the mafic volcanic rocks constitute the upper part of an ophiolite sequence. Analyses of the lavas show that they are tholeiitic and support this conclusion (Papezik and Fleming, 1967; Smitheringale, 1972) . A complete ophiolite sequence, consisting of peridotites overlain by gabbros, overlain by a sheeted diabase dyke complex which passes upward into pillow lavas, occurs at the base of the Snooks Arm Group (Upadhyay et al., 1971 ) . Sheeted diabase dykes are known to underlie the lowest mafic pillow lavas of the Lush's Bight Group at several localities in Notre Dame Bay (Strong, 1972, and pers. comm.) . However, several conflicting points about the geology of this region suggest that although a typical oceanic crustal sequence of Lower Ordovician age is present, older rocks occur within the ophiolite terrane in several places (Williams, Kennedy and Neale, 1972) ."

Jan 1, 1972

By Joseph W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles, as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain.

Jan 3, 1960

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Richard I. Grass

The White Pine Mine is located 4- 1 /2 miles south of Lake Superior in the western part of Michigan's Upper Peninsula. The orebody occurs in tabular, gently dipping Keweenawan sediments. GEOLOGY The orebody outcrops beneath 30-50 feet of Pleistocene clays and dips to the east and northeast to a depth of 3, 000 feet in five miles. It lies midway between the Porcupine Mountains and the Bergland Hills, both of which are steeply dipping felsite and coarse porphyry intrusives, extrusives and sediments (Figures 1 and 2). The orebody sediments were deposited in the Keweenawan basin during mid- and upper Keweenawan times. Mineralization occurs in the basal 20 to 25 feet of the Nonesuch formation, which is made up primarily of laminated siltstone s. Native copper, chalcocite, and silver are the ore minerals. The ore is mined by trackless room-and-pillar methods.

Jan 1, 1967

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979