Search Documents

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By K. Taniguchi, Y. Inada

When underground openings are excavated in rock mass for storage of Liquefied Natural Gas, hereinafter referred to as L.N.G., as its temperature is -162o C, steep temperature gradients and thermal stress occur around the openings. That is, the plastic zone and cracks around openings will expand with time. In this paper, the range of cracks which were obtained by the Crack Analysis Method and the range of the plastic zone which was obtained by the No Tension Analysis Method were investigated and compared.

Jan 1, 1986

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By K. W. Edwards

The formulation of a theoretical basis for the evaluation of in-situ coal through the use of geophysical logs is outlined. This involved the development of an approach to the interpretation of resistivity in environments having multiple conductive and non-conductive components. Utilizing this approach and other conventional interpretation techniques, a program was developed yielding accurate determinations of the in-situ percentages of coal, water and ash for the evaluation of coal deposits. Basic information obtained from the CWA program can be utilized in numerous aspects of total mine planning . Some examples of the practical application of this method are included.

Jan 1, 1978

By Y Wang

Inadequate goaf gas control may lead to gas exceedances in the ventilation return air, which will trip power in longwalls and cause production stoppage. To effectively control gas emissions, Australian mines heavily rely on drilling vertical goaf holes to capture coalmine methane before it migrates to mine openings. The wide application of goaf gas drainage may change the goaf pressure distribution, lead to more ventilation air leakage, and consequently increase gas explosion and spontaneous combustion risks. This paper focuses on analysing goaf gas drainage production data from a case study longwall mine in Australia. The correlation between suction pressure, total flow rate, gas flow rate and air leakage rate were analysed in detail as the face-to-hole distance changes. Suction pressure is found to be positively correlated with total flow rate, and their correlation also varies at different goaf locations due to various goaf compaction and flow resistance. This paper also proposed a theoretical method to calculate the goaf resistance of ventilation air leakage pathways. Based on several basic assumptions and different goaf drainage scenarios, the leakage airflow pathway resistance in the goaf at different face-to-hole distances can be calculated. The model results suggested that the resistance of air leakage pathways from the working face to individual goaf holes increased with the face-to-hole distance. The resistance results can also be used to calculate the corresponding permeability at the same position, which can be used as input data for CFD or Ventsim models.

Oct 12, 2022

By C. J. Hall

An investigation of multi-shaft airflow problems by the author in 1976 (1) was presented in the hope of arousing considerable written comment, but in fact-. only one contribution (2) was forthcoming. The investigation in this paper is taken several stages fur¬ther, because the matter is of major importance in many American hard rock mines with complex networks extending over thousands of meters vertically. The examples used have all been generated thermodynamical¬ly and checked by motive column (denisty) calculations. Dry air has been used to reduce the amount of time spent on the rather complex calculations, but it has been shown (3) that the principals developed apply equally well to air/vapor/water mixtures. Initially the subject is investigated using both thermodynamic and motive column analyses. The latter part of the paper concentrates on a motive column presentation. Both methods are, of course, equally valid and give identical answers to any situation when correctly applied, as is shown in the worked examples.

Jan 1, 1980

By J. N. Hummel

THE methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view, The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic.

Jan 1, 1931

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By L. B. Lindemuth

To those who are in a position to carry the thought to a conclusion; I would like to present a theory for the cause of blisters in galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered because the reason for their formation is entirely obvious. Blisters that occur periodically with no apparent system of ocation, number, size or grouping, and then disappear with no. apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pressure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or washing and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening where it entered as moisture.The pressure so generated forces the sheet apart along those lines of lamination ;hat may be found in practically all flat sections of steel rolled comparatively cold. The increase in volume. from moisture to steam at 800° F. is 2244 times the original volume of the moisture. The pressure generated by ;he moisture heated to 800° F. and entirely confined would be enough to expand or explode any container. This would explain the source of sufficient pressure to cause a sheet to blister.

Jan 3, 1927

By C. P. Crawford

Bureau of Mines Technical Paper 172, by S. H. Katz and H. C. Porter, entitled "Effects of Moisture on the Spontaneous Heating of Stored Coal", says at the outset, "Spontaneous fires in storage piles of bituminous coal' have been the source of trouble and loss since the industrial utilization of coal began. In Europe the idea arose that spontaneous combustion is more liable to happen during wet weather than during dry. Statements favoring or opposing this idea have crept into the literature. Conflicting conclusions, based on experiment as well as opinions based on observations of various degrees of reliability, are given in most of the recorded discussions of the subject. "Because of the uncertainty of the effect of moisture and its seeming importance among the conditions that affect spontaneous combustion in stored coal, the work described in this paper was undertaken by the Bureau of Mines. The experiments showed that a coal from Illinois oxidized faster when dry, whereas a sample of Pittsburgh coal oxidized faster when moist. These discordant results and similarly inconsistent results from the observations of different investigators may be coupled with the fact that under actual conditions of, storing, both coal and air always contain a considerable amount of moisture." The foregoing report of the investigations of the Bureau demonstrates that the mystery of spontaneous combustion has not yet been solved. This fact adds to the fascination of the subject. I became interested in the matter about ten years ago in observing what was probably one of the best exhibitions of this phenomenon. The old dump at Castle Gate No. 1 Mine contained boney coal and track cleanings generally. In winter when snow fell upon this old dump, the snow was soon melted by the heat of the dump which was comparatively warm at all times. Within 48 hours afterward little blue flames were in evidence on the surface of the pile. Few of the gas feeders were sufficiently constant to maintain a steady flame at any given point, but shifting emissions of gas were ignited one by another, resulting in a continuous popping and apparent running about of the flames. Another interesting exhibition of spontaneous heating was to be seen a few years ago in the storage coal piles of the local sugar factories. This coal was piled in concrete lined pits and the latter were filled with water. However, or this occasion the coal extended above the surface of the water. At every plant where this condition existed the coal was affected heating, and in each case the affected area was in a plane horizontal to and from 8 to 1.4 inches above the water level. The height of the hot area above the surface of the water appeared to be affected by the fineness of the coal. It is well known that oily rags have a tendency to heat when allowed to accumulate in some location protected from free air circulation. For some reason, as yet unknown, this does not apply to petroleum or its derivatives. Now, the most common explanation of spontaneous combustion is that the combustible material oxidizes by being brought into contact with air in the presence of moisture, the theory being that the moisture acts as a catalytic agent. My theory is that spontaneous combustion is due to oxidation of combustible matter by free oxygen carried in solution by a liquid, the oxidation taking place only as, when, and at the place where this oxygen is released from solution by the evaporation of the liquid. Also, this oxidation takes place to some degree regardless of the condition of the combustible-whether it be lump coal, coal dust, straw, wheat flour, coke, or any other combustible but, as the speed of oxidation is directly influenced by temperature, it follows that spontaneous combustion only becomes noticeable or serious in cases where the resulting heat' cannot escape as fast as it is generated.

Jan 1, 1925

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By S. Gopalan, J. D. Milshtein, S. N. Basu

Production of syngas is proposed utilizing the W/W03 redox system and employing a solarpowered two-step thermochemical cycle. Three chemical reactions occur in two chambers. Assisted by a solar concentrator, a high temperature reaction reduces W03 powder to metallic tungsten in both chambers. Subsequently, the temperature in one of the chambers is lowered and H2(g) is produced via re-oxidation of the tungsten powder using steam. The temperature in the other chamber is simultaneously lowered to an intermediate temperature and CO(g) is produced via oxidation of the tungsten powder using C02(g)· The gas streams coming out of the two chambers result in the syngas production. A complete thermodynamic analysis of the system is described. The W/W03 redox cycle offers greater gravimetric fuel productivity compared to previously proposed systems, and the entire cycle can be operated below 1273K.

Jan 1, 2013

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983