Search Documents

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969

By Somasundaran P., M. Vasudevan, Z. Dai, D. R. Nagaraj, T. Bhambani, P. Patra

Historically, efficient beneficiation of ultramafic ores has been challenging, partly due to a lack of clear scientific understanding of the effects of Mg silicates, particularly fibrous serpentines, on selective Ni recovery. Recent research at Columbia-Cytec as a part of a Vale JDP project has led to new insights into the mechanistic aspects of the adverse effects of Mg silicates. Our research has provided strong evidence to support the hypothesis that the adverse effects of Mg silicates are mediated through their large influence on pulp rheological properties, far more than any other pathway. The severity of the effect of Mg silicates is predominantly dependent on the aspect ratios of Mg silicates. For example, the pulp viscosity increases dramatically with increase in the fibrous nature of the gangue mineral leading to poor Ni separation. Various ways by which the suspension rheology affects flotation sub-processes, with implications for remedy are discussed. The insights and results have served to develop (or construct) a phenomenological model to adequately explain all of the ore flotation data, particularly the Mg silicate transport to the froth phase and the concentrate.

Jan 1, 2011

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

By S. Renslow, G. Wang, L. R. Moore, Y. Xiong, J. Gu

"Clays are known to contribute to a wide range of mineral processing challenges. These challenges can haunt a plant from the pit, through the beneficiation plant and even to the tailings pond and process water. Each step that the clay is present potentially experiences significant and costly impacts to the process efficiencies. The effect of clay minerals on the performance of phosphate flotation was investigated. The investigation led to an understanding of the movement of clay through the beneficiation plant, the impact on reagent usage, and the overall flotation performance. INTRODUCTION With the decline in mineral feed grades, mineral processing will continue to face challenges. One significant challenge would be obtaining high recoveries of industry specified quality mineral concentrates with lower quality raw minerals. Other challenges may be the handling of the excess tails and process water being produced to maintain a mill’s production volumes. For example, increased levels of clay have been, and will continue to be, a topic of concern for many mines. Some of these concerns include environmental regulations associated with water storage and discharge, as well as beneficiation. Gonglun Chen reported that clays produced in the phosphate industry are generally colloidal and fine (90% < 45 µm) (Chen, 2006). As such, these clays can take 20-30 years to settle, in the absence of polymeric assistance. The settling of these clays is essential as an accidental discharge can lead to substantial impacts to the wildlife and ecosystem. The Environmental Protection Agency (EPA) has referenced cases where the discharge of water can result in fines in the tens of millions of dollars, and at times causing the processing plants shut down, depending on the volume and quality of this discharged water (EPA, 1997). The turbidity discharge criteria will vary from state to state. Florida’s Department of Environmental Protection has listed a turbidity maximum of 29 NTUs, or 60 mg/L total suspended solids, above the natural background condition (Florida Department of Environmental Protection, 2016). A lot of the literature has been focused on the impact of high levels of clay (>10%) on mineral processing. Farrokhpay has reported the significant impact of clay minerals on froth stability in copper flotation (Farrokhpay, 2012). He reported that clays can form a hydrophobic slime coating on the surface of bubbles, which can yield an increase in froth stability. Clay concentrations as low as 5% can have significant impacts on the rheological properties or slurry viscosities. Increased slurry viscosities can lead to either elevated pumping/processing energies being required, decrease in flotation efficiencies due to a decrease in bubble mobility through the pulp, or decreased throughput to manage these viscosities (Tu, 2005; Farrokhpay, 2013; Burdukova, 2014)."

Jan 1, 2017

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016

By Thomas J. Keefe, O&apos

Results of metal electrodeposition experiments conducted at the University of Brussels and University of Missouri-Rolla over the past few years are reviewed in terms of the relationship and impact on industrial processes. Examples are cited from common electrowinning, electrorefining, or electroplating operations for copper, zinc, nickel, cobalt and silver. The following topics are considered : metallographic structure, crystallographic texture, surface morphology, nucleation and growth, additive monitoring and effects, high current density, substrate related properties including adhesion. The studies were conducted on a variety of scales from laboratory beaker tests to full sized pilot and industrial operating plants.

Jan 1, 1993

By M Bilodeau, G Caro, R Beaudoin, D Labrie

In 2005, Dyno Nobel Canada Inc, DynoConsult and CANMET-MMSL used their pool of expertise in blasting, ground control, open pit and underground mining, mineral processing, information technology and applied mineralogy to launch a research project aimed at evaluating the role of electronic detonators in the development of a sustainable energy-efficient rock reduction process. The overall objectives were to improve health and safety in a mining environment and reduce energy consumption and greenhouse gas (GHG) production in the Canadian mining industry. The study was conducted in a quarry located in Nova Scotia, Canada, with the objective of taking advantage of the higher accuracy and flexibility of electronic detonators towards improving blast efficiency and measuring its impact on productivity in a quarry environment and energy savings. Optimising the blast sequence was the first aspect to be considered before starting to look at designing bigger blasts and achieving productivity improvements, without creating additional environmental concerns, as the quarryÆs location was representing a challenge in itself in the surrounding community. The use of high-speed cameras (500 fps) was an improved means of analysing blast dynamics during the firing sequence. Seismic monitoring and linear superposition techniques were also applied to validate the sequences to be tested in all three specific geological areas. The combination of field measurements allowed to identify the optimal blasting sequences that would then be delivered accurately with the electronic initiation systems. The data from 12 blasts (six with electronic detonators and six with pyrotechnic detonators) carried out in three different geological formations (soft, medium and hard rock) showed that the electronic blasting technology could increase rock fragmentation by 15 to 20 per cent. A more uniform distribution of rock fragment size was also obtained. Blast improvements on downstream processes resulted in a five per cent productivity increase in rock excavation and transportation, a ten per cent energy reduction in primary crushing and a 15 per cent increase in the primary crusher throughput. A prototype soft-sensor based on primary crusher data (eg energy consumption, throughput, feed and product size distribution) and a simplified computer process model were developed for online measurement of a rock operating work index. Furthermore, rock samples were collected and specimens were prepared in order to determine the tensile and compressive strength of the rock materials, evaluate the aggregate crushing work index and examine the development of micro and macro-fractures under binocular and scanning electron microscopy (SEM). Blast-induced rock damage was evaluated at the end of the laboratory testing program. A reduction in rock hardness by about 30 per cent was observed after blasting. However, the impact of the blasting method (eg using electronic versus pyrotechnic detonators) on the induced rock damage was either absent or not perceptible within the measurement technique accuracy and the number of samples analysed.

Jan 1, 2007

Major underground gold mine developments are not common in Australia especially when they are totally owned and hence financed by a relatively small public company. Ballarat Goldfields Limited with its Ballarat East Project is such a company. Financing a $20m underground exploratory access programme in a poor economic climate places added importance on the quality of the project. Critical factors such as ore reserves, environment, planning and the development program are of immense importance in devising and implementing a workable finance package that satisfies both the shareholder and the project&apos;s needs.

Jan 1, 1990