Search Documents

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By Scott, Turner

IN 1933, the monetary metals were produced in a ratio of 6.7 oz. of silver to 1 oz. of gold, the lowest relatively for silver since the period from 1851 to 1865. At the beginning of that period, the virgin placers of California -and Australia began producing almost simultaneously; in consequence, there was an abrupt fall in the high silver side of the ratio that had prevailed through the centuries after America was discovered. The output from the Comstock and other silver-bearing lodes, located a decade after this influx of new gold began, soon restored the production ratio to its former proportion, that is, a relatively large weight of silver compared to gold.

Jan 1, 1934

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958

The development of reliable and accurate solution sampling systems plus on-line atomic absorption spectrophotometers and voltammetric analysers at Pasminco Metals - EZ's (PMEZ) zinc refinery at Hobart, Tasmania, has led to extensive implementation of On-Stream Analysis (OSA) throughout the hydrometallurgical circuit. These systems complement industrial autotitrator and colorimetric analysers and with the comprehensive use of a powerful integrated Distributed Control System (DCS), provide extensive monitoring and control of all the important in solution' parameters for the plant. Samples can be left unaltered, or filtered or settled, to remove solids. They are then precision diluted and pneumatically transported to analyser shelters, where they are analysed for zinc, acid, copper, cadmium, lead, antimony, cobalt, nickel, mercury and ferrous, ferric and/or total iron. The range of analyses depends on the sample itself. The results are used for feed forward and/or feedback control of reagents where possible, or simple trend monitoring and out-of-specification alarming when closed loop control is not practical. The overall system reliability and accuracy is such that many daily composite plant samples are no longer analysed off-line. Operator sampling has also been reduced, and in two places, autotitrators with automatic sample pre-treatment have been installed for preparing and analysing samples collected by operators.

Jan 1, 1993

By J. L. SCHUELER

THE writer has reread Mr. Ingalls' interesting article in the July, 1923, issue of MINING AND METAL- LURGY on "The Use of Spelter in Galvanizing." It seems that most writers, in commenting upon coatings of spelter on sheets and wire, dwell upon the thin coatings which these materials carry, and rightly so. However, they seem to forget that until very recently, in the case of wire, the manufacturer did not know how to apply a heavy coating of spelter to the wire, especially if the wire was to be woven into fence or fabricated in some other manner, because heavy coatings of spelter are exceedingly brittle. This is even true in the case of high-grade spelter, but to a lesser degree than with Prime Western. Because of this brittleness, it has been necessary for wire manufacturers to smooth the coating by passing the wire through tightly compressed wiping means of some kind, usually asbestos. This removes all of the excess spelter and allows only a thin coating to remain. The latter, as a rule, is malleable and the wire can be fabricated without material injury to the coating.

Jan 1, 1924

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By Yinan Zhang, Y. Luo

Most of the reported coal spontaneous combustion events occur in surface and underground mines where low rank coals (i.e., subbituminous and lower for this particular studies) are extracted indicating their high propensities for spontaneous combustion. Low rank coals have high moisture content (15 to 45%) and are capable of absorbing more moisture in dried condition. However, it is hard to induce the initial stage of self-heating process for the low rank coal using the current laboratory R70 testing method — a method widely used in the coal industry. Like a sponge, dry low rank coals can absorb water vapor in the air while the heat contained in the moist air is transferred to coal and served as the required activation energy to initiate the coal self-heating process. In order to prove this theorem and quantify the effects, the R70 adiabatic oxidation testing method has been improved to introduce a controlled moist flow into the coal reaction vessel. Tests using the new method and its setup on low rank coals showed that the initial self-heating process of coal sample can be greatly accelerated by the added water vapor — impossible with the regular R70 method. Once the self-heating is sustained, the removal of air moisture can further accelerate the process.

Sep 17, 2021

By Keith S. Liddell

Gold in many ores occurs in sulphides, which, if the gold is finely disseminated, renders the ore refractory and therefore not amenable to the simple process of milling and cyanidation. Traditional methods of treatment of these refractory ores is to produce a sulphidic flotation concentrate which is roasted to form a porous calcine from which the gold is recovered by cyanidation. The roasting process imposes a constraint of a minimum sulphur grade of the concentrate on the flotation plant, which may lead to a lower gold recovery being achieved in the flotation section. Thermal decomposition of the concentrate by roasting means that the sulphur contained therein has to be treated and disposed of in an environmentally acceptable manner; and, if arsenopyrite is present in the concentrate the environ- mental aspects will be worsened. It has long been recognized that finer milling of gold-bearing materials improves the liberation of gold, especially when the gold particles are very fine. After extensive laboratory and pilot plant investigations (Liddell, Patents), a suitable mill has been developed for the mining industry by Metprotech, which is capable of producing very fine grinds (down to 90 percent passing one m if necessary). In the course of the investigations it has been found that a large number of gold-bearing materials are amenable to fine milling. A specific advantage that fine milling of sulphidic materials has over oxidative processes such as roasting and bacterial leaching is that the sulphides are not decomposed and there is therefore not a sulphur disposal problem. Furthermore, the milled sulphides can become a future sulphur feed source, and can be reclaimed if necessary. A further feature of the Metprotech process is that it is possible to add cyanide to the mill feed

Jan 1, 1988

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981