Search Documents

By B. Tiryaki

Longwall shearers usually suffer from excessive pick and pickholder consumptions and severe wear of the back plate of the clearance ring section of shearer drums. In practice, most of the drums were seen to be withdrawn from the face due to the abovementioned problems, while vane picks and their holders were intact due to the improper lacing design of the clearance ring picks. However, few underground investigations and their results on the effect of lacing arrangement of clearance picks on the service life of shearer drums have been published. Nevertheless, the pick consumption characteristics of shearer drums were not investigated in detail, since these are fewer pick consumptions with shearers when compared to roadheaders. This paper is concerned with the comprehensive in situ trials on the effect of lacing of clearance ring picks on the lifespan of shearer drums, and the pick consumption characteristics of longwall shearers at Cayirhan Coal Mine in Turkey. The lifespan of shearer drums employed with shearers in this mine increased 70 per cent, while the consumption rate of clearance ring picks decreased threefold through using an alternative lacing for clearance picks, indicating the significance of utilizing proper design techniques for clearance ring picks for the service life of shearer drums. Statistical analyses carried out, using the raw pick consumption data, implied that the clearance ring picks experienced much higher loads than vane picks, revealing that special attention must be paid to designing clearance ring picks. An average maximum consumption value of 41 was determined for clearance ring picks, with corner-cutting picks having the most replacements, while it was 35 for vane picks, on three-day based pick replacements.

Jan 1, 2004

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By Edwin B. Johnson

The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but no appreciable tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962.

Jan 3, 1963

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By F. Heivilin

If the past is the key to the future, we will have ?tough? times maintaining Industrial Mineral reserves we have and proving new reserves around our plants and in new locations. The tough times will come from resources being more difficult to find, more hoops to go thru to make them Proven or Probable reserves. As always, Industrial Minerals require competitive quality, location, and costs. Since in most cases the market has suppliers, you will have to take away customers from their present supplier. This may take years or not happen even with lower cost higher quality raw materials. To determine the finished cost for a new deposit you need to design, determine capital costs, and operating costs for a new plant . Stripping, mining, hauling, processing, and transportation costs are part of the equation. After satisfying that your costs are in line you will need to do production tests to make sure the process works on the ore. You may want to complete permitting before purchasing the property. If you are new in the business you will have to prove you can deliver the right quality, the right quantity, on time consistently year after year at lower cost to take away a customer. Without being in the market this will be hard. The cut off grades to enter a market may be much lower than sale indicates because a competitor often lowers the price to keep you out of the market. We have many more items to check before the new deposits can be put on reserves. Our old reserves will require drilling to check for new products and prove that they do not contain items that would make them unusable for our product line or cause permitting problems. Archeological checks, wetlands, more water discharge testing, county zoning, and endangered species are among many items that have been added to mine permits. There will be more. A 4-6 page mining permit becomes 30-300 pages and consists of 5-15 permits, any of which might be a fatal stumbling block. It is not guaranteed that we can mine what we have on reserves. We may fight and lose. Oil-Dri?s loss in Reno and LaPort?s in England are examples where permitting failed. The NOx, sulfur, and carbon problems are just starting. Dioxin is in the background requiring monitoring on food products to Europe. What other anions, cations, endangered species, and land types are going to be problems in the future are guesses now. What new products are we going to have to test for and cause out of balance reserves? If there are none we probably won?t be here. We are competing for land use with ?Endangered Species?, wetlands, farming, forestry, cities, roads, and hunting. We?ve mined the best quality, low overburden, easiest to mine and process raw materials. The price of land and taxes are increasing. Old royalties are 2-3 times the present acre value instead of 8-10 times the property value when leased. Land taxes are up. It was and is best that we get the land in Fee Simple Title. This isn?t always possible. However, plants are closing and people have overlooked, made mistakes in drilling or interpretation of deposits. These may be opportunities. China is eating up high quality ?Industrial Minerals ?which have caused prices to rise. We may need to change our cutoffs? in terms of smaller pit sizes and higher overburden ratios. This is money in the bank. Overburden ratios and other items increasing cutoff costs need to be rethought. Suddenly doubling cutoff ratios for overburden and decreasing pit sizes are good alternatives to looking elsewhere where we might not be able to mine for a number of reasons. The higher prices make them competitive, especially when a competitor goes out of business. However, our low overburden ratios and short hauls around our plants are not safe from new roads, condemnation by county or city governments (N. J.), zoning changes (Reno, FL., CA, and environmental regulation changes (Buffers GA, MS). New roads ?Interstates? can take reserves, increase hauling distances and reduce tons per load. Let?s combine the Refractories, fullers earth, and bentonite industries and use the last 40 years as a guide to the future looking for problems and opportunities. Some or most of the following will apply to other minerals. WHERE DO WE LOOK? First, on our own properties, those next to our properties and on properties near our competitor?s plants. Where the profit margin has increased, the distance from the plant and thickness of overburden we can use is increased. The thickness of clay is decreased. For new locations we pick the ideal location and look at deposits and closed or open operations in ever increasing distances away from that location. We need to be aware of: 1. Increased transportation costs a. Access to Roads -Backhauls b. Haul with doubles and triples c. Railroads - Loading on sidings - Ability to get switches - Cars/backhauls versus rates 2. Cost of building a new plant 3. Cost of infrastructure 4. Cost of repair or new equipment when purchasing an operating or shutdown plant. 5. Local, state, and federal mine and environmental permitting. When exploring around an established operation expect that property acquisition, drilling, mining, stripping, and hauling costs will be greater due to them having second, third, or even fourth the pick of the deposits. I found this in New Jersey looking for refractories and around Quincy, Florida looking for attapulgite. You may be able to get some better properties because the operating company has angered some land owners, their drillers missed the clay, or the property wasn?t available when they were actively exploring for reserves. You may have some product lines your

Jan 1, 2009

By W. E. Wallace, V. Robinson, M. F. Keane, V. Vallyathan

"An in vitro study of the biologic responses of surface-modified and native silica and kaolin was made to provide comparative information on the supression of cytotoxicity by pulmonary surfactant. The release of alveolar macrophage cytoplasmic enzyme, lactate dehydrogenase (IDH), and lysosomal enzymes B-N-acetylglocosaminidase (B-NAG) and B-ghucuronidase (B-GLUC) and sheep blood-cell hemolysis were moni¬tored as indicators of cell membrane damage and cytutoxicity. Surface modification of silica and kaolin with dipalmitoyl lecithin (UPI) resulted in complete abrogation of cytotoxicity of both minerals. These findings indicate that surface modification of minerals with different adsorption properties by pulmonary surfactant generally lessens their prompt adverse effects.INTRODUCTIONAcute and chronic silicosis are well-characterized clinical and pathologic entities resulting from the inhalation of crystalline silica (Morgan and Seaton, 1984). Kaolin, a layered aluminosilicate clay frequently mined and used in manufacturing, contains tetrahedral silica alternately layered with alumina octahedra. Kaolin is relatively .inert biologically, and distinctly greater pulmonary burdens are seen in patients with kaolinosis than are seen in patients with silicosis. Crystalline siliea (quartz) induces a significantly greater degree of fibrosis in exposed animals in vivo than does kaolin (Hamilton and Hardy, 1974; Parkes, 1982; Hunter, 1976; Sheers, 1964; Warraki and t-lerant, 1963; Lynch and Mciver, 1954; Lapenas et al., 1984).This difference in pulmonary disease associated with the two types of dust is not reflected by in vitro cytotoxicity as Jetermined by pulmonary macrophage bioassays or erythrocyte hemolysis. Cytotoxicity studies using crystalline silica and kaolin of similar size fractions show comparable bioassay response on a mass basis. These cellular bioassays, therefore, do not correlate with the relative in vivo pathogenicity of silicates."

Jun 1, 1988

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By Kumar Ashish, Shukla Akhilesh, Kr. Rokkam Kiran, M. Sheeba, S. Sombhatla Sundar

"Purification of zinc leachate plays a predominate role in zinc leaching refineries, to produce impurity free cathode sheets. As a part of such purification sequences, copper cementation with zinc dust is the preliminary step, since the presence of copper will preferentially deposit during zinc electro deposition and has the effect of reducing current efficiency. The cake thus produced is being accumulated as an inventory, due to invariable market and leading to space constraints & hazardous ambience. Hence, a project has been taken up for in-house generation of copper sulphate solution through ammonical leach followed by solvent extraction process and utilizing it as an active promoter for zinc sulphide flotation in Hindustan Zinc’s own captive mines. Cold purification cake majorly contains copper (30-40%) along with zinc (10-20%) and cadmium (2%). Confirmation to the above statement, photomicrographs of purification cake also confirmed the major presence of copper in metallic or oxidized form. In present work ammoniacal carbonate leaching of purification cake followed by solvent extraction using diketone based solvent has been studied under the influence of various parameters viz., temperature, agitation, pulp density, ammonia, CO2 dosages, solvent concentration, and impact of w/s zinc on leaching and solvent extraction. Leaching kinetics determined based on shrinking core model. Chemical reaction at unreacted core was found to be the rate controlling step. The estimated activation energy was found to be 24 KJ/mol. Leached copper has been extracted by solvent extraction with a ß diketone based solvent and is stripped with sulfuric acid as concentrated copper sulfate solution. The above established R&D findings are successfully implemented in the Commercial plant with a treatment capacity of two tons of cold purification cake per batch. Till now 500 MT of Purification cake has been treated, and generated 6500 MT of copper sulphate (55 g/l Cu), with final Cu recoveries between 87-90%."

Jan 1, 2018

By Robert W. Roscoe

For over a century, St. Joe Minerals Corporation in Southeast Missouri has been sinking shafts for their lead mining operations. Upon discovery of the Viburnum Trend, or "New Lead Belt", St. Joe brought its experience and expertise in shaft sinking to the area. Eleven shafts were then sunk in an 18 year period, ending in 1972. In 1981, St. Joe began sinking a new shaft in the Trend with hand-picked employees from the four operating lead mines and service facilities. The paper describes the general history of St. Joe shaft sinking methods and equipment, focusing on the current development of the Viburnum No. 35 Shaft.

Jan 1, 1983

By A H. Gray

Gekko Systems Pty Ltd engaged in the test work, design, manufacturing and commissioning of the pre-concentration plant at Silver Standard Resources Inc’s Pirquitas mine in the north western Jujuy province of Argentina. Testing of the ore at coarse feeds of between 2 and 12mm returned probable recoveries of up to a total of 95% silver into 50% of the mass fed to the InLine Pressure Jigs (IPJ’s). The plant has been designed and built based on the test results to include a preparation screen to bypass the fines that are naturally higher in grade and repulping of the coarse which is then pumped to three parallel trains of 2-stage IPJ roughing-scavenging. The target 50% yield to concentrate passes over a dewatering screen and the solids are returned back to the mill feed conveyor. The IPJ tails are transferred to a dewatering screen and solid rejects are stockpiled off the end of a transfer conveyor. All dewatered underflow products are processed via hydrocyclones to recover dirty water for use back into the IPJ circuit and return entrained fines to the fines bypass line.With the sulphide orebody being processed, the results from operations to date have shown that plant performance is matching the original laboratory sulphide ore testwork data. The objective of the pre-concentration step is to both reject gangue and achieve grades between 300-400g/t Ag to the float circuit as flotation recoveries are maximised within this range. The plant currently achieves overall upgrades of approximately 150% of feed grade with the IPJ only circuit producing an average 180% increase from calculated feed grade.

Aug 8, 2011

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By D. R. Babich, R. A. Allwes, L. V. Wade

The design of a longwall entry system is discussed in this Bureau of Mines paper. This is done primarily through the results of an in-mine case study made of two sets of longwall entries utilizing the stiff- yield pillar design concept. The rock mechanics instrumentation plan used in this case study is shown, including a description of the instrumentation layout and the types of instruments used. The analysis of the stress changes in the abutment and yield pillars is presented in detail as the longwall panels were mined. Conclusions concerning when the pillar first started to experience significant stress, pillar stress history as the longwall face approached and moved past the pillars, stress distribution within the pillars and relative stress changes between yield and abutment pillars are discussed. The paper concludes with a discussion of the redistribution of stress in the vicinity of the long- wall panel.

Jan 1, 1982

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By Scott W. Harrison, Richard E. Aaseng

In 1993 Ispat Inland Mining Company began mining its Laurentian ore reserve, which has six distinct ore types that are extremely variable. Initially batch processing was necessary to optimize mining equipment utilization. The variability as found in the ground was compensated for in plant operation, which proved ineffective. When the last of the six ore types was introduced in 1997, production, quality, and cost were seriously impacted. In-pit blending was the solution developed by the process management team to provide the plant feed required to economically process all six ore types in the Laurentian reserve.

Jan 1, 2000

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017