Search Documents

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By Mark C. Malamphy

MAJOR JUAREZ TAVORA, who recently accepted the post of Minister of Agriculture in Brazil, has reorganized his department. Not least among those sub: divisions of the "Ministerio" which underwent radical changes in the general reform was the Serviqo Geologico e Mineralogico do Brasil. This well- known organization was declared extinct, and in its place was created a new cleparttnent ' termed "Departamento Nacional cle Producqao Mineral," which immediately took over all the work of the olcl Servico Geologico ill addition to certain new duties. Dr. .. Domingos Fleury- da Rocha, former head of the School of Mines of Ouro Preto, was called to Xio to assume the newly created post of Director General of the department of Mineral Production. His department will have live divisions :

Jan 1, 1934

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By L. K. ARMSTRING

ANYONE doubting prosperity in the mining industry should visit the Kootenays of British Columbia where the West Kootenay Power & Light Co. is kept busy running new power lines and connecting mines and mills with lines already in service. Quoting from an inspired statement "The four hydro-electric plants of the West Kootenay Power & Light Co. on Kootenay River have been in continuous operation." At the recent 35th annual meeting of the Eastern' British Columbia Boards of Trade held in Nelson, a two-day session indicated unusual activity. The following information was obtained through personal contact, through the press, and by hearsay. Much of it has been checked and proved accurate. Reversing the order of the flowsheet. Secretary J. R. Hunter reported as fol¬lows regarding the value of the 1934 production of the Consolidated Mining & . Smelting Company's metallurgical, plants at Trail and Tadanac:

Jan 1, 1935

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of eomposition at the temperatures from 850K to 1050K. An alloy was vaeuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By S. N. Sinha

The distribution coefficients of lead and silver between copper and matte phases have been measured at two different temperatures. Experiments covered the ranges of 0.009-1.8, 0.07-0.13, and 0-11 wt pct lead, silver, and iron in matte, respectively. The distribution coefficients of lead have been measured at 1405 and 1505 K and correlated with lead and iron concentrations in metallic copper and matte. The values of the distribution coef¬ficient of lead between copper and iron-free matte, at infinite dilution of lead, have been determined to be 3.60 and 4,06 at 1505 and 1405 K, respectively. The distribution coefficient of silver between copper and iron-free matte is independent of silver concentrations and has been measured to be 2.13 and 2.21 at 1400 and 1500 K, respectively. For an iron-bearing matte, the distribution coefficient of silver has been correlated with iron concentration in the matte at both 1400 and 1500 K. From the measured values of distribution coefficients, the Raoultian activity coefficients of PbS and AgS0.5 in copper-saturated matte have been calculated. At infinite dilution, the following equations correlating the Raoultian activity coeffici¬ents of PbS and AgS0.5 with matte- composition and temperature have been obtained: log Y° PbS =1.515 + 1080/T 0.14 NFes lbS Fog YAgS = -0.074 - 425/T + 0.09 NFes. - 0.5

Jan 1, 1983

By Liwen Hu, Jianxun Song, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

The subchloride titanium was prepared by sponge titanium and titanium tetrachloride in the CaCl2 at 1173 K. The species were detected are mainly titanium dichloride, and the average valent in the melt are 2.05. The accurate equilibrium constants were obtained for the reaction 3Ti2+ = 2Ti3++Ti after the accurate activities of titanium chloride were evaluated with emf method, and the observed deviations from ideal behavior are discussed.

Jan 1, 2015

By G. H. Lind

This paper discusses the traditional costing approach currently used in the underground coal mining industry. Activity Based Costing (ABC) is identified as being a potentially more effective manner in which to cost underground coal mining systems. With the use of a costing framework developed by the author incorporating new thinking to eliminate the shortcomings identified in the traditional costing approach, a comparison of two types of underground coal mining systems, viz. continuous miner and longwall, is conducted. It is found that under certain criteria, in all cases, irrespective of the way in which the systems are costed, the continuous miner system is currently the better investment. It is also observed that when a system is costed using ABC that better investment decisions result when compared to costing the same system using traditional costing techniques. It is further seen that traditional costing techniques tend to overestimate the total costs of a mining system. This paper shows one application of ABC that can be incorporated as a management tool.

Jan 1, 2001

By Shinya Otsuka

Activity coefficient of oxygen in sulfide-rich and metal-rich melts in copper-sulfur binary were determined at 1423 and 1523 K by means of a modified coulometric titration technique using the following cell: 0 ( is Cu-S melts) I Zr02 (+Ca0) I air, Pt The activity coefficient values obtained in the present study increase rapidly with sulfur composition in the vicinity of xs = 0.3333. The data obtained for the matte saturated with the metal-rich melts are in good agreement with those obtained by Kuxmann and Benecke, Schmied 1, and Eguchi and Yazawa. Those obtained for the metal-rich melts are in good agreement with the results of Sano and Sakao.

Jan 1, 1983

By Lester Guttman

THE connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermo-dynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall&apos;s statistical method resembles closely that called by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulae for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß-brass; 2. a- brass; 3. AuCu3; 4. AuCu. When the temperature is so high that no long-range order exists, these formulae reduce to the same form for all lattice types, namely: [ ] Here the symbols have the following meanings: [F-Helmholtz free energy E-energy S-entropy k-the gas constant per molecule z-coordination number, (e.g. 12 in. a-brass). N-total number of atoms c-atomic fraction of A] VAA, VBB, VAB-energy per bond of the corresponding bonds log means log, throughout The superscript 0 denotes the thermo- dynamic function in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition [ ] The free energy may also be written in terms of µA and µB, the chemical potentials or partial free energies per atom:

Jan 1, 1948

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering materiaL Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to dcsign new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass speetrometer.

Jan 1, 2003

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

As discussed previously, total cost is the sum of the direct materials, direct labor, and production overhead costs. The assignment of direct materials and direct labor costs to individual activities is generally straightforward. The assignment of overhead often is not. Overhead costs frequently contain allocations that only approximate the demand the activity has made o; the overhead resources. The inaccuracy of the overhead calculation can create erroneous production cost information and lead to suboptimal management of the operation. This problem is particularly acute when determining the production cost of individual products in multiproduct firms. Pricing, process management, and product mix decisions are especially susceptible to errors in product costing. The problem of properly determining production cost is complicated by the fact that few if any alternative methods exist to identify the inaccuracies in overhead allocation. To avoid errors, some firms simply ignore overhead costs in their product cost calculations, particularly those resulting from marketing and distribution of the final product.

Jan 1, 1999

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019