Search Documents

By Behrouz Ohadi, Kamran Esmaeili, Bibhu Mohanty

In most metalliferrous open pit mines with heterogeneous orebodies, blast-induced rock movement is a crucial outcome that has unfavorable impact on ore and waste segregation in the post-blast muck pile, resulting in either ore loss (the ore is misclassified as waste and sent to the waste rock dump) and/or ore dilution (waste is misclassified as ore and sent to the processing plant). While many studies have been carried out to assess the influence of blast design parameters on blast-induced rock movement, the influence of rock mass characteristics in these studies have been overlooked.

Jan 1, 2018

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By Siyuan Zhang, Lu Lin, Yanping Bao, Wei Xiao, Chaojie Zhang

In order to decrease high aluminum consumption in Interstitial-Free (IF) steel production in a steel plant, Ruhrstahl Heraeus (RH) process data from 2428 heats were analyzed by statistical methods. The results showed that the blowing oxygen quantity and oxygen activity, before the RH and before deoxidization, have positive correlations with aluminum consumption, especially the blowing oxygen quantity. Waiting time before refining also has a positive correlation with aluminum consumption when it exceeds 7 min. On the contrary, steel temperature before RH has a significant negative correlation with aluminum con sumption, when it is between 1600 and 1630 °C. According to the statistical results, the RH refining process was optimized when the steel temperature before RH was controlled between 1630 and 1645 °C, waiting time was controlled at less than 7 min, blowing oxygen quantity was controlled to less than 100 m3, and the oxygen activity before RH was controlled between 0.050–0.075%. After optimization, the reduction of aluminum consumption was remarkable. Average aluminum consumption decreased from 1.45 to 1.17 kg/t steel.

Mar 1, 2017

By Kristie D. Tarr

Ideally, in situ monitoring would supply the input data for numerical modeling of backfill material property requirements. However, clue to production requirements and costs of conducting field tests, input data are often based on small-scale laboratory tests. The size of test samples is known to play an important role in the laboratory assessment of the behaviour of geotechnical materials, including backfill. There are observed differences between the mechanical properties of laboratory-scale samples and those of in situ materials, and these are generally attributed to the differences in scale. Various scaling factors have been proposed for converting laboratory observations to anticipated in situ conditions for soil and rock materials. With regard to mine backfill, very limited studies exist which have involved the effects of sample size on material properties. The literature indicates that reported backfill strength data are based on a variety of test sample sizes and in some cases, specimen geometries. Carefully determined laboratory scale effects could play an important role in estimating the potential backfill behaviour in the field, especially when developing new backfill systems. Laboratory studies were conducted with sample diameters ranging from 50 to 300 mm. Scale factors relating specimen size to strength were developed wherever possible, and are presented in this paper

May 1, 2008

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Francis O. Otuonye

The results of an ongoing study to determine the response of full contact rock bolts to shock waves due to blasting are presented. A time domain systems modeling and analysis technique was used to identify the axial and bending response of the bolt when explosives charges are detonated at close-in distances.

Jan 1, 1993

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

By Xie Zhang, Chongyang Zhao, Qingyun Huang, Bing Xie, Xiaopeng Zhen

"Extracting vanadium from vanadium containing hot metal into vanadium slag by BOF is the main vanadium production process in China. In this paper, the influence of Si content in hot metal on the quality of vanadium slag is analyzed. Synthetic vanadium slag with different SiO2 content were melted at 1673 K and then cooled to 303K at the cooling rate of 3?/min. Optical microscopy, SEM, EDS and XRD were used to analyze the mineralogical phases and crystallization behavior of vanadium slag. The results show that vanadium slag mainly contains spinel phase and silicate phase; V is enriched in the spinel phases while Si is concentrated in Fe2SiO4 CaFeSi2O6 and (Fe,Mn)2SiO4 as silicate phase. The melting point of slag increases gradually with the addition of SiO2; whereas viscosity decreases with an addition of 15~19% SiO2 and increases with an addition of 19~27% SiO2.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys. The major vanadium products include FeV, V2O5, V2O3, VN and Al-V-Ti alloy. Furthermore, vanadium slags are mostly produced by oxidizing the elements in V-containing hot metal during a duplex refining process. Therefore, the process of removing vanadium from hot metal has its significance on the subsequent process[1].The extraction of vanadium is greatly affected by the mineralogical composition of vanadium slag[2], the distribution of the elements between the spinel and silicate phases and its physic-chemical properties. These characteristics of vanadium slag have been studied in some details. It has been reported that Si mainly exists mainly in the form of silicate which wraps the spinel crystals while small amount of Si stands as phosphorus quartz or diopside[2]. Chen et al.[3, 4] points out, when SiO2 content in vanadium slag increased every 1%, V2O5 decreased 1.48%. Moreover, silicate phases would embarrass the oxidation of V-containing spinels through decreasing the exposing probability[5]. Meanwhile, melting point and viscosity of vanadium slag has been greatly influenced by the SiO2 content. Therefore, this work attempts to analyze the above-mentioned questions systematically."

Jan 1, 2012

By H. C. Kenny

THE annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200° to 350° C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet-though several investigators, beginning with Caesar and Gerner1 in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper-data are lacking on the problem: What is the specific influence of different amounts of silver on this tem-perature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it-is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also signifi-cant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered.

Jan 1, 1934

By Shuqiang Guo, Gonghui Yang, Xingxing Zhang, Yuyang Bian, Song Chen, Weizhong Ding, Yinhe Liu, Lan Jiang

One of the most promising refractory materials for application is zirconia in melting superalloy. In this work, the properties and phase composition of magnesia partially stabilized zirconia ceramics (MgO-PSZ) under different sintering temperatures were systematically investigated. Commercial magnesia partially stabilized zirconia (MgO-PSZ) powders were selected as the starting materials. The magnesia partially stabilized zirconia phase composition was measured by X-ray diffraction (XRD), the density of sintered samples was tested by vacuum density instrument, the thermal expansion were obtained by thermal dilatometer from ambient temperature up to 1450°C, and the microstructures of MgO-PSZ were characterised by scanning electron microscope (SEM). The results indicated that the properties of thermal expansion, densification, microstructures and phase composition were significantly affected by sintering temperature. Densification was consistent with SEM micrographs of MgO-PSZ at different sintering temperatures.

Jan 1, 2015

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the' shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress 'system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical' specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

INTRODUCTION Conventional roof support methods such as mechanical and resin bolting provide adequate support for a wide variety of coal mine roof conditions. However, roof falls remain the single largest cause of death and injury in underground mines and seriously hamper production in many operations, demonstrating that these methods of roof support are not universally effective. One of the most recent and successful advances in coal mine roof control has been the introduction of the roof truss. Although past work on roof trusses (Gambrel1 and Haynes, 1970; Sheory, et al, 1973) shows little quantification of this support technique, numerous field examples have been cited where the truss effectively supported roof which could not be controlled by either mechanical or resin bolts (Kegel, 1969). The truss combines the advantages of both inclined roof bolts and post-stressing the roof. However, the full benefits of roof trusses will only be realized when design criteria to optimize support capacity are determined. The number of trusses required for a given roof condition can then be minimized, reducing installation time and making them economically more feasible. The purpose of this research is to develop roof truss design criteria based initially on laboratory studies of gravity-loaded multi-layered photoelastic mine models. Laboratory test results will then be modified where necessary following future field testing. The ensuing relationships should provide the field engineer with a reliable means of calculating optimum truss configuration, capacity, and spacing for a set of known roof conditions.

Jan 1, 1977

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905